NAND Chip Mask ROM Mode Short Location

[soldiaz]

Hello.
I have a Kiwibox S3 Plus SanDisk X505260971 .

Try shortening indicated area

[freddy]

Hi
Anyone knows test point location for X96 Air P3? Thanks

Hard to help without image of PCB both sides
Or reference to a thread with pics of board

Or anything more other than written text

Happy Testing

[the4anoni]

Hi
Anyone knows test point location for X96 Air P3? Thanks

[Light]

Hello.
I have a Kiwibox S3 Plus that I need to reflash but I don't know which pins to short. Can anyone help me?
It's a SanDisk X505260971 I think.
Thanks in advance.

[ath156]

Hello.
I've bricked my Beelink GT1 2gb/16gb with s/n S912BKLG90140, and i dont know which pins i have to short circuit.
I've googled and only found gt1 ultimate or gt1 but with a board diferent from mine.
Could anyone please help me?
Thanks

Try this

[CrazyHacker]

Hello.
I've bricked my Beelink GT1 2gb/16gb with s/n S912BKLG90140, and i dont know which pins i have to short circuit.
I've googled and only found gt1 ultimate or gt1 but with a board diferent from mine.
Could anyone please help me?
Thanks

[matrix55a]

You dont need maskrom mode

Install Terminal Emulator apk in Android
Type reboot/ recovery

Make sure UBT is running
You have loaded image
And hit start button.

Should recognize and start Flash

I install Termux and Qute terminal but reboot/ recovery dosn't work. Go to settings/about/system update and get acces to android recovey mode. Push start UBT and my img write to device.

Thank you for your help:-)

[freddy]

Thank you for your reply. I bridge tck and ground and nothing happend. Where is 4 test point in Image 3? I need maskroom because my reset switch dosn't work. In atvXperience_v2E firmware dosn't work remote tool and wifi. When i update OTG this firmware 20170215 mxq pro s905x软件 get acces to android recovey mode but i can't upload img. I don't copy my remote.conf because user not root :-(

You dont need maskrom mode

Install Terminal Emulator apk in Android
Type reboot/ recovery

Make sure UBT is running
You have loaded image
And hit start button.

Should recognize and start Flash

Img 3 if you expand for closer look the points are there right tight to edge of chipset
Upper n lower

Further good luck

Happy Testing

[matrix55a]

If you want to tickle the Nand

Third image
There are 4 inner test points right beside chip
Bridge the upper 2

Thank you for your reply. I bridge tck and ground and nothing happend. Where is 4 test point in Image 3? I need maskroom because my reset switch dosn't work. In atvXperience_v2E firmware dosn't work remote tool and wifi. When i update OTG this firmware 20170215 mxq pro s905x软件 get acces to android recovey mode but i can't upload img. I don't copy my remote.conf because user not root :-(

[freddy]

Hi, can you help me with MXQ PRO 4K. Short pin 6/7?
Thank you.

Man this is old board 2016...

First image below cpu heating are test points
3.3 volt
Tdi
Tdo
Tck
Gnd
And others

What happens if you bridge gnd and tck(test clock)

If you want to tickle the Nand

Third image
There are 4 inner test points right beside chip
Bridge the upper 2

Maybe will work

Are you sure you even need maskrom?

Can be many issues with UBT

Happy Testing

[matrix55a]

MXQ PRO 4K atvXperience_v2E android 7.1.2. Short pin 6/7 or 7/8 dosn't work for me. USB_Burning_tool v2.0.8 not detect Board

[matrix55a]

6-7 and 7-8 dosn't work for me:-( USB_Burning_Tool not detect device. MXQ PRO 4K firmware atvXperience_v2E Android 7.1.2.

[phankhanh86]

Hi, can you help me with MXQ PRO 4K. Short pin 6/7?
Thank you.

may be 7-8

[matrix55a]

Hi, can you help me with MXQ PRO 4K. Short pin 6/7?
Thank you.
PS. Sorry for repeating the post.

the short pin is 6/7 thanks

[matrix55a]

Hi, can you help me with MXQ PRO 4K. Short pin 6/7?
Thank you.