NAND Chip Mask ROM Mode Short Location

[freddy]

where pin to short
i short 7-8 8-9 5-6 not work
thank somuch

First img
underside of board
2 copper pads
Looks like below Nand
Try there

Happy Testing

[phankhanh86]

where pin to short
i short 7-8 8-9 5-6 not work
thank somuch

[mAtvXk]

Pxelinux ...

I'm not familiar with the linux environment, probably a missing drivers...

[Seba75r]

Remove any mSD card / USB key attached to tv-box, you have to flash firmware .img with USB Burning Tool using USB male-to-male cable.

Yes, i know. But PC not detecting device.
Pxelinux its for network booting?

[mAtvXk]

Some things wrong

Remove any mSD card / USB key attached to tv-box, you have to flash firmware .img with USB Burning Tool using USB male-to-male cable.

[Seba75r]

X96 Max+

Some things wrong

[Seba75r]

X96 Max+

Thank You i WILL TRY

[mAtvXk]

... test point for this unknow x96 pcb. cpu s905x3

X96 Max+

[Seba75r]

Hello. Im looking for test point for this unknow x96 pcb. cpu s905x3

[ath156]

mmh...you mean light when powering up? Cant find picture, you have one showing nand? and those pins your friend shorted

Obviously he does not remember what exactly he did and what pins he connected....also obviously he must have done many (possibly risky??) tries....
Any way we already know which pins to short in most of the different versions of this TVbox (Beelink GT1 or Ultimate version). It is always at the same area. I will upload some photos if anyone will need them (I really hope noone will need this).
So the only question was to those that managed to brick this TVbox and managed to revive it : "When the GT1 was completely bricked and you connected the power adapter at it - Was any light ON or nothing???"

[soldiaz]

Because as already I said:
- This box is not mine, but a friend's TVbox.
- He thinks that he permanently damaged his TVbox by connecting the wrong pins
- He tried to revive it, but with no success
- He no longer has any kind of light (red or white) anymore. I think that even when the GT1 is completely "bricked", it still gives some light when you connect it to power or to the PC/laptop with the firmware cable. Is it so? Therefore the question to other users that bricked the GT1. Otherwise he most probably really damaged the GT1 by connecting some wrong pins !!

mmh...you mean light when powering up? Cant find picture, you have one showing nand? and those pins your friend shorted

[jalldoc]

G10max androidTV / p281 / Amlogic S905W / S905XQ4_V4.0 / SV6256P

[ath156]

Do not know but why not revive n flash and see?

Because as already I said:
- This box is not mine, but a friend's TVbox.
- He thinks that he permanently damaged his TVbox by connecting the wrong pins
- He tried to revive it, but with no success
- He no longer has any kind of light (red or white) anymore. I think that even when the GT1 is completely "bricked", it still gives some light when you connect it to power or to the PC/laptop with the firmware cable. Is it so? Therefore the question to other users that bricked the GT1. Otherwise he most probably really damaged the GT1 by connecting some wrong pins !!

[soldiaz]

To anyone that ever bricked his Beelink GT1.
When it was bricked did it still give a red light from the SPDIF port OR nothing at all?
This is to help a friend to decide if his GT1 is permanently damaged (i.e. due to shorting the wrong pins) OR if it is like this because of the brick state.

Do not know but why not revive n flash and see?

[vargapi]

This is X96 MAX plus 2/16 gb
Can you tell me where to short circuit?