NAND Chip Mask ROM Mode Short Location

[freddy]

Anyone can help with this board?? (Amlogic S905W)

Hmmmmmm

2nd image bottom left is pinout for u-art
Square hole is gnd then tx rx vcc 3.3v
Looks like small line diagram with bridge at tx rx

Just to the right is a component
Bridge that
Maybe will work

Or connect u-art

Hope it helps

Happy Testing

[hiko25]

Steps:
1) Unplug the bricked TV Box from the power source.
2) Insert SD Card into SD card reader and plug it into your PC.
3) Open up PhoenixCard software, Select your firmware using the "image" button, Then check on "start up" button. Click on burn and come back in 30mins. It might look like its stuck at 24% but its running, trust me.
4) Open Phoenix Suite and charge the ROM.IMG
5) When your SD Card is ready, plug it into your TV Box. Take a stick/cotton bud and insert into the "AV" port and push down till you feel the button. Keep it pressed and insert the USB CABLE previously connected to your PC.

Then the flash procces should start. when finished unplug the USB cable and the micro SD memory.
Connect and test.

I hope this helps you.

thank you for reply this method doesn't working

[darkas]

Anyone can help with this board?? (Amlogic S905W)

[phankhanh86]

Hello every one please i want tje short pin of this box name is X96 mate

Steps:
1) Unplug the bricked TV Box from the power source.
2) Insert SD Card into SD card reader and plug it into your PC.
3) Open up PhoenixCard software, Select your firmware using the "image" button, Then check on "start up" button. Click on burn and come back in 30mins. It might look like its stuck at 24% but its running, trust me.
4) Open Phoenix Suite and charge the ROM.IMG
5) When your SD Card is ready, plug it into your TV Box. Take a stick/cotton bud and insert into the "AV" port and push down till you feel the button. Keep it pressed and insert the USB CABLE previously connected to your PC.

Then the flash procces should start. when finished unplug the USB cable and the micro SD memory.
Connect and test.

I hope this helps you.

[hiko25]

Hello every one please i want tje short pin of this box name is X96 mate

[Limberrb]

Muchas gracias me has salvado

[ath156]

To anyone that ever bricked his Beelink GT1.
When it was bricked did it still give a red light from the SPDIF port OR nothing at all?
This is to help a friend to decide if his GT1 is permanently damaged (i.e. due to shorting the wrong pins) OR if it is like this because of the brick state.

[phtp]

Anyone know where the Mask rom pins are for a Tanix Tx8 Max s912 3gb ddr4? The chip says it's a GCAI and I can't find anything diagrams related to it.

GCAI
GCBNA 1S08FC0-CD1
D10N61001A

[superceleron]

Tanix X4 (s905x4) Mask rom location.

View is from the TOP of board...

[Deses]

Hello!

I got this X96 Mini Plus using a S905W4 chip, and I can't flash it with anything. It always fails, so I wonder if shorting the pins would help. The problem is that I don't know which ones I have to flash.
Here are the pictures of my board. I hope you can help me.

https://imgur.com/a/g0oGld9

[mpalozis]

Hello guys. I'm trying to flash a new firmware to HK1 Mini+ but no luck. I have short the corrent pins and in Batchtool 1.8 its being recognized and a blue light shows in number 1, (which means the box is musrom mode) but when i press the upgrade button Download boot Succes, Wait for muskrom SUcces, But Test Device Fail. I don't know what else to do. In USB burning tool (in many different versions) the box isn't recognized. Just to add I'm using Driver Assistant 4.4.

Hi again
I have problem with A95X Pro a95xa1_V2_0 a1w 905w 6051p.Can someone help short pins pls?

[rex2323]

Как прошиться если китайцы кнопку reset не завезли (кнопка тупо не припаяна, выяснил при разборке)

[rex2323]

Hi guys, help me with the board below, pls
X96q need short pin for this model for installons atv9
And please send me link of original firmware x96q 4gb 32gb thanks

[dodbda]

Hi guys, help me with the board below, pls

Amlogic s905x - Q96 MINI (A95X R2)


Thanks!!!