NAND Chip Mask ROM Mode Short Location

[mastermark]

Connect the two pins from the right pic

[davidluispires]

Did it. Thanks for your help but it didn't worked. I tried it with a screwdriver and with a clip... and nothing. :-(

[loulapirate]

Hello everyone !!!!

Can anyone help me and know the pins to reset my H96+ bricked? I found for the V2 but I can not find anything for the v1 ...
thank you all

Hello guys !

nobody has the v1 ?

[mastermark]

show your board

[jukyO]

Hello everyone !!!!

Can anyone help me and know the pins to reset my H96+ bricked? I found for the V2 but I can not find anything for the v1 ...
thank you all

Hello everyone !!!!

Can anyone help me and know the pins to reset my H96+ bricked? I found for the V2 but I can not find anything for the v1 ...
thank you all

I have the same board and the same issue.
Can anyone help to identify which pins to short on V1 LPDDR3 version?

[jukyO]

Hello guys !

nobody has the v1 ?

I have it, H96 Pro + , V1, LPDDR RAM (4K Ultra HD TvBox on top)

Managed to short connect pins.

Picture 1 shows side on which pins are.
Picture 2 shows position of pins on PCB (cyan).
Picture 3 shows two possible pairs ( blue or red pair).
Picture 4 shows V1 on other side of the board.

Steps:

1. Plug USB cable to USB connector closer to power supply connector and other side to PC .
2. Short connect blue or red pair as per pictures attached.

You'll hear sound of PC of detection of board.
Plug out usb cable, plug power supply or usb back, board should be alive now, and no need to short it again .

Then you have to play further with Amlogic USB burning tool or sdcard methods ( use of toothpick).

[Donk]

Hello Guys,
I ne ed some help with my board T9 4GB ram Rockchip 3328. can you tell me which pins I should stick. Thank you

[loulapirate]

I have it, H96 Pro + , V1, LPDDR RAM (4K Ultra HD TvBox on top)

Managed to short connect pins.

Picture 1 shows side on which pins are.
Picture 2 shows position of pins on PCB (cyan).
Picture 3 shows two possible pairs ( blue or red pair).
Picture 4 shows V1 on other side of the board.

Steps:

1. Plug USB cable to USB connector closer to power supply connector and other side to PC .
2. Short connect blue or red pair as per pictures attached.

You'll hear sound of PC of detection of board.
Plug out usb cable, plug power supply or usb back, board should be alive now, and no need to short it again .

Then you have to play further with Amlogic USB burning tool or sdcard methods ( use of toothpick).

Thank you very much guys !!!!!!!! Coooooooooool
I will try that today !!!

[Donk]

Hello Guys,
I need some help with my board T9 4GB ram Rockchip 3328. can you tell me which pins I should stick. Thank you

Guys , no sound when I plug to the computer only sptif socket lighting up and nothing more

[loulapirate]

I have it, H96 Pro + , V1, LPDDR RAM (4K Ultra HD TvBox on top)

Managed to short connect pins.

Picture 1 shows side on which pins are.
Picture 2 shows position of pins on PCB (cyan).
Picture 3 shows two possible pairs ( blue or red pair).
Picture 4 shows V1 on other side of the board.

Steps:

1. Plug USB cable to USB connector closer to power supply connector and other side to PC .
2. Short connect blue or red pair as per pictures attached.

You'll hear sound of PC of detection of board.
Plug out usb cable, plug power supply or usb back, board should be alive now, and no need to short it again .

Then you have to play further with Amlogic USB burning tool or sdcard methods ( use of toothpick).

Hello, I tried tonight but I did not succeed.
little question, with what do you bridge the two reds pins or the two blue pins ? I see lots of videos or they just press with a screwdriver. you solders ? or can I just take an electric cable?

thank you

[jukyO]

Hello, I tried tonight but I did not succeed.
little question, with what do you bridge the two reds pins or the two blue pins ? I see lots of videos or they just press with a screwdriver. you solders ? or can I just take an electric cable?

thank you

I used common screwdriver.
Try several times, plug out and in usb cable. Also try to plug in power adapter.

[syked69]

Hi,

Can anyone please assist with telling me what to short on Tanix TX9 pro with S912 and SDINADF4-32G eMMC. Currently not recognized in AML USB burning tool

images located here

[Guest]

Pins for X96Max:

[soldiaz]

syked69 : had same issue. I Connected male-male cable and Power. Then wipe over pins until beep sound

[ulas12]

https://i.hizliresim.com/jg83dj.jpg

https://i.hizliresim.com/Emg8jq.jpg

https://i.hizliresim.com/26r1pN.jpg

https://i.hizliresim.com/BarPjD.jpg

https://i.hizliresim.com/ZXZklk.jpg

Incorrect software installation does not see the computer device anymore


tried pins 5-6 6-7 7-8

HELP MEE!!!!!