NAND Chip Mask ROM Mode Short Location

[victorsyt]

Dear friends, Who does know which pins have I to close for switch tv box ( T95ZPlus-3G3-v1073 ) to download mode.
In my T95Z Plus the memory chip is KLMBG4GEAC-B001. Datasheet https://datasheetspdf.com/parts/KLMB....pdf?id=911298
I can't understand.

[tteodor]

T95z plus v.1081 3gb where is pins to reset?

[victorsyt]

{"alt":"Click image for larger version Name:\timage_39169.jpg Views:\t0 Size:\t52.4 KB ID:\t794078","data-align":"none","data-attachmentid":"794078","data-size":"medium"}

T95z plus v.1081 3gb where is pins to reset?

Your case:

[tteodor]

Your case:

No, not work for me

[Jansley]

HELP.
What pins I shgould shortcut?

YOUIT - R98 - 4GB - 64GB
RK3318
Samsung klmbg4gend-b031
what is the right usb? USB 3.0 or USB 2.0? Bricked

someone?

[mkosta]

HELP.
What pins I shgould shortcut?

YOUIT - R98 - 4GB - 64GB
RK3318
Samsung klmbg4gend-b031
what is the right usb? USB 3.0 or USB 2.0? Bricked

Try short one of these two to ground...

[mkosta]

This one is for X88 PRO 4G/64G (RK3318)

[JansleySouza]

Try short one of these two to ground...

unsuccessfully

[mkosta]

unsuccessfully

Sorry about that...

Did you use USB2.0? install drivers?

On my X88 PRO (post above) I manage to find it using voltmeter.

I found pin (opposite side of NAND chip) with voltage (when powered ON) and then grounding it temporarily during boot.

Regards.

[JansleySouza]

Sorry about that...

Did you use USB2.0? install drivers?

On my X88 PRO (post above) I manage to find it using voltmeter.

I found pin (opposite side of NAND chip) with voltage (when powered ON) and then grounding it temporarily during boot.

Regards.

Thank you for your help I used the USB2.0 and USB3.0! Correct is USB2.0?
I have the voltmeter. How can I find the grounding pin?
Regards.

[uranium237]

Hi,
I have bricked mygica 1900pro by installing a beta firmware.
I have located Samsung KLMAG2WEPD-B031 emmc chip on the board, however I don't see a way to short any pins there.
Any help is greatly appreciated. I'm attaching front and bottom pictures:

[whcamera]

X96 Air sloution:

1. Insert the USB cable into PC, run USB_Burning_Tool software, select importing the *.img file, and click Start.
2. Clean the chip pins marked on the motherboard.
3. Short-circuit 2 of them (probably 4th and 5th pins). At the same time insert the USB into the USB3.0 interface.

If the short circuit is correct, your PC will immediately discover the device and start flashing the machine when the USB cable is plugged in. Otherwise, re-select the shorting point and plug in the USB.

Enjoy

[scottmu64]

There must be an easy way to identify the two pins to short on every board?

[nttuan]

Tanix TX9 Pro-P 2GB/16GB bricked due to wrong firmware flashing. Please help me to short the pin eMMC. Thank you very much!

[Lukkaz]

I dont know much about mine but it BRICKED due to a firmware flashing and wont appear on USB Tools anymore nor even shows up connected on my pc.. please help me find the short pins!!
It still shows the green light of power when i connect to the pc but also shows a red light at the optical part.