NAND Chip Mask ROM Mode Short Location

[amitsan]

Hi nikos17m,

as per the image of your box, your board is Amlogic.

Pls try Amlogic burn card maker trick.

Follow the guide here : https://www.getdroidtips.com/downloa...rn-card-maker/

[nikos17m]

Hi nikos17m,

as per the image of your box, your board is Amlogic.

Pls try Amlogic burn card maker trick.

Follow the guide here : https://www.getdroidtips.com/downloa...rn-card-maker/

I am familiar with this method

the box is bricked and not working,first I must be able to connect to pc and then flash a correct firmware
I think it bricked because of the rom version I used
there are many varietions of this box and not all of them accept same Roms
thanks

[Guest]

...there are many varietions of this box and not all of them accept same Roms...

TANIX TX3 Max & Mini thread, post #194

If a bootloader problem you can shortcut the memory while you connect the USB cable and it should be detected by your PC:

[nikos17m]

TANIX TX3 Max & Mini thread, post #194

Thank you very much

[markshane]

Hi guys! So I bricked by HK1 Play 4/64GB flashing a ROM. The flash was successful using USB Burning tool, but the box was showing only red light when connected to TV. Tried to find the nand pins but failed and found this thread upon searching. Can someone please guide me how to short pin this box? It seems to be BGA board:

[Pandaii]

I have Z4 rk3368 2gb+16gb tv box.
While upgrading its bricked. now not detecting in PC.

Can someone help me with nand pin location?

[obiobcool]

I have a problem while I was flash tx3 mini


Help me to find short pin please

[zakariach]

Hi
can someone help me short pin Magicsee N6 Max RK3399

[jplam89]

Hi everyone!
I have a bricked mxq pro4k with a board s905xq4_v3.0
Does anyone know the pins or the points where do the short??


Thanks a lot!

Juan.

[JimmyD]

I have a problem while I was flash tx3 mini


Help me to find short pin please

I had the same problem, I found that this new TX3 mini comes with Amlogic s912, I flashed mine with S912_atvXperience_v2FF Normal + LPDDR.rar it works fine now,

LAN and display not working on this ROM
Check the attached pic for short pin.


Regards

[nith206]

Hello guys

I have an old tx3 mini without the mini logo on the box

the board is different from other tx3 mini board I’ve seen

it’s bricked do you know the pin location plz?

and what rom can I flash with this box

thank you very much and stay safe

Even I have the same board of Tanix tx3 mini hynix nand ver 1.1 , which pins to short ? I've bricked my box, please help

[obiobcool]

I had the same problem, I found that this new TX3 mini comes with Amlogic s912, I flashed mine with S912_atvXperience_v2FF Normal + LPDDR.rar it works fine now,

LAN and display not working on this ROM
Check the attached pic for short pin.


Regards

Thank you so much

but I think my device was fully bricked

[JimmyD]

Thank you so much

but I think my device was fully bricked

Are you using a male-to-male USB cable?

[nikos17m]

TANIX TX3 Max & Mini thread, post #194

I tried to do that

When I short the pins I hear a beep sound from the board and then it resets on windows because i hear the sound(connect dissconect sound) but it is still unrecognizable from the burning tools


so is my board fully dead?"
Thanks

[Guest]

You have to short pins while the UBTools is running.