TANIX TX6S Allwinner H616 Android 10.0 TV Box 2GB/16GB 2.4G+5.8G WiFi LAN Bluetooth

[onlyonce]

Check the all information about the updateFW from AllWinner and the 3rd party,
BUT No One succeed on TX6S,
1,Pressed RESET BUTTON can not into flash mode.SO AllWinner PhoenixSuit cant find device
2,No Key file,SO AllWinner LiveSuit cant run update
3,AllWinner PhoenixUSB can not read & burn H616 FW file. SO TFcard update FW fail.
4,AllWinner DragonFace Tools cant open H616 FW file also.


UNTIL checking the IC development manual to found out how to setup into flashmode.

YES,buy a cable very easy,UPDATE FW very easy .The process of finding solutions is complex.

TX6S software system is very immature and full of bugs

[RiCkLaR_atvX]

Check the all information about the updateFW from AllWinner and the 3rd party,
BUT No One succeed on TX6S,
1,Pressed RESET BUTTON can not into flash mode.SO AllWinner PhoenixSuit cant find device
2,No Key file,SO AllWinner LiveSuit cant run update
3,AllWinner PhoenixUSB can not read & burn H616 FW file. SO TFcard update FW fail.
4,AllWinner DragonFace Tools cant open H616 FW file also.

UNTIL checking the IC development manual to found out how to setup into flashmode.
YES,buy a cable very easy,UPDATE FW very easy .The process of finding solutions is complex.
TX6S software system is very immature and full of bugs

Your comment is confusing, hard to understand your point of interest. Are you just saying how bad firmwares are? Or, Are you still having problems installing firmware, or connecting device to computer?

You know the Reset Button is hidden next to SDcard slot on side of device! (Reset button is not at rear of device, this will cause problems if you didn't know this). Best thing to do is dissemble TVbox and cut out the plastic fin that blocks the reset button so you can easily access the button when you put the case back together.

I always use Phoenix_USB_Tool on windows computer to Flash the different Allwinner Firmwares,
1) load firmware in Tool
2) click START
3) hold Reset button down
4) connect USB cable while you keep holding Reset down
5) Windows system makes confirmation sound that device is connected when connected, but the Tool doesn't start Burning firmware immediately, it takes some time, maybe 1 minutes for Tool to start showing progress.
6) plug and connect TVbox to TV and wait 5 minutes for new firmware to finish first-boot start-up processes.

[RiCkLaR_atvX]

Found a work-a-round for the Network issues of the TX6S, to get the best possible speed for Networking in this device you must use a USB-to-Ethernet adapter in the USB 3.0 connection. The adapter I used was TPlink USB3.0-to-Gigabit_Etherenet connector and the device can now connect at a maximum of 90-100 Mbps download speed.

[c,lei]

Hi ,

Nice to see , Risky Dude , hope both calm down , had 2 Flags because of it ,

Flagger did the right , good hope for the Future that they do it right now , we

all have Errors , nobody is pefect , but to know and change it is the best thing ,

i know it is frustrating to see , that there is no Support for the Box that bought ,

next Time they buy a Shield , or Ugoos or similar better supported China Boxes ,

greetings / gefattern

Check out youtube, see the comments about Nivida Shield from people who bought one before shelling out around $200 for one.

Not worth it, especially if you're not a PC gamer/Nivida fanboi.

[c,lei]

Your comment is confusing, hard to understand your point of interest. Are you just saying how bad firmwares are? Or, Are you still having problems installing firmware, or connecting device to computer?

You know the Reset Button is hidden next to SDcard slot on side of device! (Reset button is not at rear of device, this will cause problems if you didn't know this). Best thing to do is dissemble TVbox and cut out the plastic fin that blocks the reset button so you can easily access the button when you put the case back together.

I always use Phoenix_USB_Tool on windows computer to Flash the different Allwinner Firmwares,
1) load firmware in Tool
2) click START
3) hold Reset button down
4) connect USB cable while you keep holding Reset down
5) Windows system makes confirmation sound that device is connected when connected, but the Tool doesn't start Burning firmware immediately, it takes some time, maybe 1 minutes for Tool to start showing progress.
6) plug and connect TVbox to TV and wait 5 minutes for new firmware to finish first-boot start-up processes.

Actually, the best thing to do is take an old credit or similar card and cut a strip of plastic off it using scissors so that it will slide inside/into the vent slot in front of the reset button so you can press the button as you would using a paper clip or toothpick.

No need to damage or dissemble anything.

[c,lei]

Your comment is confusing, hard to understand your point of interest. Are you just saying how bad firmwares are? Or, Are you still having problems installing firmware, or connecting device to computer?

You know the Reset Button is hidden next to SDcard slot on side of device! (Reset button is not at rear of device, this will cause problems if you didn't know this). Best thing to do is dissemble TVbox and cut out the plastic fin that blocks the reset button so you can easily access the button when you put the case back together.

I always use Phoenix_USB_Tool on windows computer to Flash the different Allwinner Firmwares,
1) load firmware in Tool
2) click START
3) hold Reset button down
4) connect USB cable while you keep holding Reset down
5) Windows system makes confirmation sound that device is connected when connected, but the Tool doesn't start Burning firmware immediately, it takes some time, maybe 1 minutes for Tool to start showing progress.
6) plug and connect TVbox to TV and wait 5 minutes for new firmware to finish first-boot start-up processes.

Actually, the best thing to do is take an old credit or similar card and cut a strip of plastic off it using scissors so that it will slide inside/into the vent slot in front of the reset button so you can press the button as you would using a paper clip or toothpick.

No need to damage or dissemble anything.

This is what I came up with to acess the reset button on my MXQ Pro 4K and TX6 Type devices:

[bushrang3r]

Has anyone had an issue with this box where it won't power up if the reset button is being held down?

[dartyard]

hello this box is good or not? or bad firmware?

does anywant mod for atv?

[kokovi4]

TX6S OTA update 23.03

[dartyard]

TX6S OTA update 23.03

Latest?? How about temp??

[kokovi4]

Yes, from yesterday, So, little good , continue test .

[belloto]

it is the same shit (sorry), but in a higher version.
nothing works, and it's impossible to install apps.

Waiting for a new version.

[RiCkLaR_atvX]

TX6S OTA update 23.03

Any Changelog on this new update?

Or did you notice any significant changes with this new update?

[belloto]

Nothing.

[Turkmenator]

Somebody try Local Update - dynamic system update.Some people can update to 20200331 FW
I have 20200323 and system can't update