Announcement

Collapse
No announcement yet.

USB Burning Tool Error restore firmware

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

    USB Burning Tool Error restore firmware

    I have TX3 Pro android box and it's bricked. I want to restore the firmware with usb burning tool but it always getting error when I start it. It stuck on 4% at download UBOOT. This is the error code :

    [17:16:46 906][HUB5-3][Inf]--Start burning...
    [17:16:46 961][HUB5-3][Inf]--------------ERASE BOOTLOADER------------
    [17:16:46 961][HUB5-3][Inf]--2-2-0-0
    [17:16:46 961][HUB5-3][Inf]-------------Download DDR.USB-----------
    [17:16:46 961][HUB5-3][Inf]--2-2-0-0
    [17:16:46 961][HUB5-3][Inf]--Control write pll reg1 0xd9000000:0x000000b1
    [17:16:47 466][HUB5-3][Inf]--Control write pll reg1 0xd9000000:0x00005183
    [17:16:47 967][HUB5-3][Inf]--Write initial succeed
    [17:16:47 967][HUB5-3][Inf]--Upload encrypt at 0xc8100228
    [17:16:47 967][HUB5-3][Inf]--ulValue = 0xadfc318c
    [17:16:47 967][HUB5-3][Inf]--Read encrypt value succeed
    [17:16:47 977][HUB5-3][Inf]--Transfer complete
    [17:16:47 977][HUB5-3][Inf]--Run at address 0xd9000000
    [17:16:47 977][HUB5-3][Inf]--RunInRam succeed
    [17:16:48 003][HUB5-3][Inf]--2-2-0-0
    [17:16:48 003][HUB5-3][Inf]--CheckFileRunState succeed
    [17:16:48 003][HUB5-3][Inf]--runResult:0x 0,paraMagic:0x7856efab
    [17:16:48 003][HUB5-3][Inf]--ddrCapacity:0x 800
    [17:16:48 003][HUB5-3][Inf]-------------Download UBOOT.USB-----------
    [17:16:48 003][HUB5-3][Inf]--2-2-0-0
    [17:16:48 003][HUB5-3][Inf]--ulValue = 0xadfc318c
    [17:16:48 003][HUB5-3][Inf]--Download DDR.USB buffer at 0xd9000000
    [17:16:48 014][HUB5-3][Inf]--Transfer complete
    [17:16:48 014][HUB5-3][Inf]--Download UBOOT.USB buffer at 0x0200c000
    [17:16:48 163][HUB5-3][Inf]--Transfer complete
    [17:16:48 168][HUB5-3][Inf]--DownCheckPara succeed
    [17:16:48 168][HUB5-3][Inf]--Run at address 0xd9000000
    [17:16:48 213][HUB5-3][Err]--generatedAddSum:0x9a08fe06;srcAddSum:0xf32140ea;ru nResult:0x e6;paraMagic:0x7856efab
    [17:16:48 213][HUB5-3][Inf]--ReadCheckPara failed
    [17:16:48 288][HUB5-3][Err]--[0x79730902]Unknown
    [17:16:48 288][HUB5-3][Inf]--Close device handle 0x000003e4

    OR

    [17:17:47 493][HUB5-3][Inf]--Start burning...
    [17:17:47 544][HUB5-3][Inf]--------------ERASE BOOTLOADER------------
    [17:17:47 544][HUB5-3][Inf]--2-2-0-0
    [17:17:47 544][HUB5-3][Inf]-------------Download DDR.USB-----------
    [17:17:47 544][HUB5-3][Inf]--2-2-0-0
    [17:17:47 544][HUB5-3][Inf]--Control write pll reg1 0xd9000000:0x000000b1
    [17:17:48 048][HUB5-3][Inf]--Control write pll reg1 0xd9000000:0x00005183
    [17:17:48 550][HUB5-3][Inf]--Write initial succeed
    [17:17:48 550][HUB5-3][Inf]--Upload encrypt at 0xc8100228
    [17:17:48 550][HUB5-3][Inf]--ulValue = 0xadfc318c
    [17:17:48 550][HUB5-3][Inf]--Read encrypt value succeed
    [17:17:48 560][HUB5-3][Inf]--Transfer complete
    [17:17:48 560][HUB5-3][Inf]--Run at address 0xd9000000
    [17:17:48 560][HUB5-3][Inf]--RunInRam succeed
    [17:17:48 586][HUB5-3][Inf]--2-2-0-0
    [17:17:48 586][HUB5-3][Inf]--CheckFileRunState succeed
    [17:17:48 587][HUB5-3][Inf]--runResult:0x 0,paraMagic:0x7856efab
    [17:17:48 587][HUB5-3][Inf]--ddrCapacity:0x 800
    [17:17:48 587][HUB5-3][Inf]-------------Download UBOOT.USB-----------
    [17:17:48 588][HUB5-3][Inf]--2-2-0-0
    [17:17:48 588][HUB5-3][Inf]--ulValue = 0xadfc318c
    [17:17:48 588][HUB5-3][Inf]--Download DDR.USB buffer at 0xd9000000
    [17:17:48 597][HUB5-3][Inf]--Transfer complete
    [17:17:48 598][HUB5-3][Inf]--DownRunPara succeed
    [17:17:48 598][HUB5-3][Inf]--Run at address 0xd9000000
    [17:17:59 246][HUB5-3][Inf]--Detect Device remove timeout
    [17:17:59 246][HUB5-3][Inf]--Device is connected
    [17:17:59 246][HUB5-3][Inf]--Close device handle 0x000004ec
    [17:17:59 301][HUB5-3][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#5&2b47b14&0&3#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x00000504
    [17:18:04 359][HUB5-3][Inf]--2-2-0-0
    [17:18:04 359][HUB5-3][Err]--CheckFileRunState failed
    [17:18:04 359][HUB5-3][Inf]--Failure : 1, FailureMax : 3
    [17:18:04 864][HUB5-3][Err]--[17:18:04 864][HUB5-3][Inf]--Failure : 2, FailureMax : 3
    [17:18:05 369][HUB5-3][Err]--[17:18:05 369][HUB5-3][Inf]--Failure : 3, FailureMax : 3
    [17:18:05 434][HUB5-3][Err]--[0x10303004]Romcode/Switch status/Identify/Error result

    I also tried to restore with SD Card but nothing happen. I can't reach recovery mode. The box still showing the red led. Please help me find the solutions. Thanks

    #2
    [UPDATE]
    I successfully reach 97% but it getting error again because out of range. What it's mean?

    Comment


      #3
      Did you tried a other USB cable, just in case

      Comment


        #4
        Hi MDafiR, Open USB Burn Tool and go to View then temperature setting and untick range.
        Hope this helps
        Cheers
        Kevin

        Comment


          #5
          hi MDafiR

          Its 3 days past your post but when you this error still have, try press "Start" in Burning Tool befor you connect the usb cable (or Power cable when you have reset button in AV hole) on the box, after that connect the box and the flash begins hope complett full.
          This methode works at my SCISHION V88 PRO box.
          I hope i can help^^ and sry for my bad english :/

          Comment


            #6
            I had succesfully doing this progress by change range rate from 20-40 to 20-60. And I try to press "Start" before or after connect the device, it's the same. Thanks for all for helping me.

            Comment


              #7
              I have the same problem. Could. You tell me how you reached 97%

              Comment


                #8
                Have you fixed it?

                Comment


                  #9
                  Originally posted by georgesurgeon View Post
                  I have the same problem. Could. You tell me how you reached 97%
                  Do you have TX3 Pro ?

                  Comment


                    #10
                    Originally posted by georgesurgeon View Post
                    Have you fixed it?
                    Yes. The problem was fixed.

                    Comment


                      #11
                      Originally posted by georgesurgeon View Post
                      I have the same problem. Could. You tell me how you reached 97%
                      Hi MDafiR,

                      Can you please tell me how you manage to get past 4%? I'm stuck there.

                      [20:25:13 049][HUB1-1][Inf]--Start burning...
                      [20:25:13 101][HUB1-1][Inf]--------------ERASE BOOTLOADER------------
                      [20:25:13 101][HUB1-1][Inf]--2-2-0-0
                      [20:25:13 101][HUB1-1][Inf]-------------Download DDR.USB-----------
                      [20:25:13 101][HUB1-1][Inf]--2-2-0-0
                      [20:25:13 101][HUB1-1][Inf]--Control write pll reg1 0xd9000000:0x000000b1
                      [20:25:13 602][HUB1-1][Inf]--Control write pll reg1 0xd9000000:0x00005183
                      [20:25:14 102][HUB1-1][Inf]--Write initial succeed
                      [20:25:14 102][HUB1-1][Inf]--Upload encrypt at 0xc8100228
                      [20:25:14 102][HUB1-1][Inf]--ulValue = 0xadfc318c
                      [20:25:14 102][HUB1-1][Inf]--Read encrypt value succeed
                      [20:25:14 112][HUB1-1][Inf]--Transfer complete
                      [20:25:14 113][HUB1-1][Inf]--Run at address 0xd9000000
                      [20:25:14 114][HUB1-1][Inf]--RunInRam succeed
                      [20:25:14 136][HUB1-1][Inf]--2-2-0-0
                      [20:25:14 136][HUB1-1][Inf]--CheckFileRunState succeed
                      [20:25:14 137][HUB1-1][Inf]--runResult:0x 0,paraMagic:0x7856efab
                      [20:25:14 137][HUB1-1][Inf]--ddrCapacity:0x 800
                      [20:25:14 137][HUB1-1][Inf]-------------Download UBOOT.USB-----------
                      [20:25:14 137][HUB1-1][Inf]--2-2-0-0
                      [20:25:14 137][HUB1-1][Inf]--ulValue = 0xadfc318c
                      [20:25:14 137][HUB1-1][Inf]--Download DDR.USB buffer at 0xd9000000
                      [20:25:14 147][HUB1-1][Inf]--Transfer complete
                      [20:25:14 147][HUB1-1][Inf]--Download UBOOT.USB buffer at 0x0200c000
                      [20:25:14 275][HUB1-1][Inf]--Transfer complete
                      [20:25:14 278][HUB1-1][Inf]--DownCheckPara succeed
                      [20:25:14 278][HUB1-1][Inf]--Run at address 0xd9000000
                      [20:25:14 322][HUB1-1][Err]--generatedAddSum:0x96805ddf;srcAddSum:0x ba7f0d4;runResult:0x e6;paraMagic:0x7856efab
                      [20:25:14 322][HUB1-1][Inf]--ReadCheckPara failed
                      [20:25:14 335][HUB1-1][Err]--[0x312e0902]Unknown
                      [20:25:14 335][HUB1-1][Inf]--Close device handle 0x000002d4


                      georgesurgeon, have you managed to fix it?

                      Thanks,
                      Alex

                      Comment


                        #12
                        Hi,

                        Can anyone share please? on how they solve this issue?
                        Thanks! I am stuck on 4% with 2 pcs, 2 usb cables.

                        Comment


                          #13
                          Originally posted by derbysig View Post
                          Hi,

                          Can anyone share please? on how they solve this issue?
                          Thanks! I am stuck on 4% with 2 pcs, 2 usb cables.
                          same here.....what the problem??

                          Comment


                            #14
                            i think i have the same problem

                            Comment


                              #15
                              Originally posted by georgesurgeon View Post
                              I have the same problem. Could. You tell me how you reached 97%
                              Hi do this. open the progam select the image do not conect the box yet ,,, then change the range 10 to 80 and press start ,,, once you press the start then plug in the box , it worked for me 3 times in a row

                              Comment

                              Working...
                              X