ATV9-MOD-(P212)AMPERE-V3

[dsm150]

connect via ssh and show the output of these commands

2|:/vendor/etc/dropbear # dmesg | grep wifi
[    0.000000] Kernel command line: init=/init console=ttyS0,115200 no_console_suspend earlycon=aml_uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 otg_device=1 reboot_mode_android=normal androidboot.selinux=permissive logo=osd1,loaded,0x3d800000,576cvbs maxcpus=4 vout=576cvbs,enable hdmimode=1080i60hz frac_rate_policy=1 cvbsmode=576cvbs hdmitx=,444,8bit cvbsdrv=0 irq_check_en=0 androidboot.firstboot=0 jtag=apao androidboot.veritymode=enforcing androidboot.hardware=amlogic page_trace=on androidboot.rpmb_state=0 androidboot.serialno=1234567890 androidboot.wificountrycode=US ro rootwait skip_initramfs androidboot.dtbo_idx=0 vmalloc=512m --cmdline root=/dev/mmcblk0p18 buildvariant=userdebug
[    1.553457] wifi: power_on_pin_OD = 0;
[    1.555833] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
[    1.561747] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
[    1.568419] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
[    1.575063] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
[    1.595273] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=487
[    1.601224] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
[    1.608217] aml_wifi wifi: [wifi_dev_probe] power_on_pin=486
[    1.614087] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
[    1.620119] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
[    1.625509] aml_wifi wifi: [wifi_setup_dt] irq num is:(69)
[    1.631072] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(487)
[    1.637031] aml_wifi wifi: [wifi_setup_dt] power_on_pin(486)
[   11.988300] dhd_wifi_platform_load: Enter
[   11.997372] wifi_platform_set_power = 1
[   12.006575] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Disable! 486
[   12.214815] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Enable! 486
[   12.722708] wifi_platform_bus_enumerate device present 1
[   13.230544] wifi_platform_set_power = 0
[   23.218085] wl_android_wifi_on in 1
[   23.221671] wl_android_wifi_on in 2: g_wifi_on=0
[   23.226332] wifi_platform_set_power = 1
[   23.235813] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Disable! 486
[   23.478517] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Enable! 486
[   24.394739] dhd_os_open_image1: /vendor/etc/wifi/buildin/config.txt (47 bytes) open success
[   24.421557] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[   24.423251] Final nv_path=/vendor/etc/wifi/buildin/
[   24.428264] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[   24.439576] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[   24.443769] dhdsdio_download_code_file: Open firmware file failed /vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[   24.478907] wifi_platform_set_power = 0
[   24.488438] wl_android_wifi_on: Failed
[   24.491805] dhd_open : wl_android_wifi_on failed (-35)
[   24.504337] wl_android_wifi_off in 1
[   24.508691] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[   24.523989] wifi_platform_set_power = 0
[   24.532785] wl_android_wifi_off out
[   29.546251] wl_android_wifi_on in 1
[   29.549970] wl_android_wifi_on in 2: g_wifi_on=0
[   29.554653] wifi_platform_set_power = 1
[   29.563858] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Disable! 486
[   29.770612] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Enable! 486
[   30.431237] dhd_os_open_image1: /vendor/etc/wifi/buildin/config.txt (47 bytes) open success
[   30.458057] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[   30.465212] Final nv_path=/vendor/etc/wifi/buildin/
[   30.469659] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[   30.475652] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[   30.483848] dhdsdio_download_code_file: Open firmware file failed /vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[   30.520193] wifi_platform_set_power = 0
[   30.528959] wl_android_wifi_on: Failed
[   30.532802] dhd_open : wl_android_wifi_on failed (-35)
[   30.545252] wl_android_wifi_off in 1
[   30.549027] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[   30.564834] wifi_platform_set_power = 0
[   30.574114] wl_android_wifi_off out
[   36.935470] wl_android_wifi_on in 1
[   36.943922] wl_android_wifi_on in 2: g_wifi_on=0
[   36.943959] wifi_platform_set_power = 1
[   36.962809] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Disable! 486
[   37.572984] aml_wifi wifi: [extern_wifi_set_enable] WIFI  Enable! 486
[   38.715571] dhd_os_open_image1: /vendor/etc/wifi/buildin/config.txt (47 bytes) open success
[   38.769828] Final fw_path=/vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[   38.781503] Final nv_path=/vendor/etc/wifi/buildin/
[   38.781550] Final clm_path=/vendor/etc/wifi/buildin/clm.blob
[   38.794927] Final conf_path=/vendor/etc/wifi/buildin/config.txt
[   38.797102] dhdsdio_download_code_file: Open firmware file failed /vendor/etc/wifi/buildin/fw_bcm40183b2.bin
[   38.881624] wifi_platform_set_power = 0
[   38.885820] wl_android_wifi_on: Failed
[   38.905977] dhd_open : wl_android_wifi_on failed (-35)
[   38.927166] wl_android_wifi_off in 1
[   38.927206] wl_android_wifi_off in 2: g_wifi_on=0, on_failure=1
[   38.944032] wifi_platform_set_power = 0
[   38.964326] wl_android_wifi_off out
:/vendor/etc/dropbear #

130|:/vendor/etc/dropbear # dmesg | grep chip
[    0.229291] Meson chip version = RevB (21:B - 82:0)
[    1.119969] hdmitx: system: hdmitx_device.chip_type : 3
[    1.313201] chip type:0x21
[   10.308030] The chip is not support hevc encoder
[   12.976035] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[   12.991114] dhd_conf_set_chiprev: chip=0x4330, chiprev=4
[   24.368562] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[   30.422170] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[   38.688316] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
:/vendor/etc/dropbear #

about voice search
I’m using an Android TV app as a remote control, and the search works, but only on YouTube. In the voice search settings, an empty window, photo below.


it was exactly the same when upgrading to android 9 on mi box S, they urgently released an update and this problem was fixed.

[bumerc]

fw_bcm40183b2.bin is missing, I will look for this FW and install it in the next update (thanks for the logs). I can't say anything about the Android TV app, I've never used it

[dsm150]

fw_bcm40183b2.bin is missing, I will look for this FW and install it in the next update (thanks for the logs). I can't say anything about the Android TV app, I've never used it

So take a look at the photo, search settings in applications, in the firmware itself do not work. The problem here is not in the remote control.

[bumerc]

ok, i will check this later

[dsm150]

ok, i will check this later

For information:
After installing the firmware, but before updating the applications in the play store:





??????After updating from the play store:

[superceleron]

For information:
After installing the firmware, but before updating the applications in the play store:

That is because google just updated their ATV assist app, and that new one has some issue with custom atv roms.

[dsm150]

Ok, one more issue.
on this rom, only one usb port works through which the firmware is uploaded. through the Second port, no one device works like a keyboard, mouse, remote usb dongle etc.

nexbox a95x s905x chip

[freakbox]

/vendor/etc/remote.cfg

Always do this via SSH or ADB with compliance with all file permissions

e.g

mount -o rw,remount /vendor
cp -a /sdcard/remote.conf /vendor/etc/remote.cfg

reboot via UI

And What about Bluetooth? I can´t turn him on, thanks

[bumerc]

And What about Bluetooth? I can´t turn him on, thanks

Your wifi chipset is not supported, this build is only for Ampak wifi, please read the first post in more detail. For other chipsets it makes more sense to create a separate build

edit: use the command "cp" without the option "-a" to copy the remote.cfg file (I corrected it in my post)

[bumerc]

Ok, one more issue.
on this rom, only one usb port works through which the firmware is uploaded. through the Second port, no one device works like a keyboard, mouse, remote usb dongle etc.

nexbox a95x s905x chip

I do not have the source code of the kernel and dt for each device, you obviously have a different layout for usb on the board

[freakbox]

Your wifi chipset is not supported, this build is only for Ampak wifi, please read the first post in more detail. For other chipsets it makes more sense to create a separate build

edit: use the command "cp" without the option "-a" to copy the remote.cfg file (I corrected it in my post)

I understand, but i really like this Firmware, is it clean Android TV, and is the newest version, have netflix support, and wifi works really fast without disconnecting, but i have problem with remote and bluetooth, and my 1st usb port (Download port) doesnt work too. Thanks for help.

[alex161rus]

bluetooth

which chip? if realtek, try replacing vendor\lib\libbt-vendor.so

[dsm150]

I do not have the source code of the kernel and dt for each device, you obviously have a different layout for usb on the board

How else can I help in debugging the ROM using my device?

[freakbox]

which chip? if realtek, try replacing vendor\lib\libbt-vendor.so

Some Fn-Link 8223A-SR F10019 1643 - I tried to replace but didn´t work


copying remote.conf to /vendor/etc still won´t work, i have blue diode which after start turn off and doesn´t light, in another roms lights still

[alex161rus]

Some Fn-Link 8223A-SR F10019 1643 - I tried to replace but didn´t work


copying remote.conf

to add ir, you need to edit
remote1-4.tab.
there are buttons