[0x32030201]Uboot/Get result/DiskInitial error

[marine_tugah]

I did tried all that no luck sir!

Can some one make a video of you using method of shorting pin?

[ath156]

I do tried the both roms and same result! I made another video!

Please try the following:
- Start USB Burning Tool. Load one of the last 2 firmwares. Press start. Connect one end of the USB cable to PC. Short the 2 pins and while shorting insert the other end of the cable to the Black USB port . Please don't stop shorting the pins even if the "burning" starts-just keep shorting them, hoping that it will pass the 7% point (I know this is tricky and it would be good if you had somebody else to help you)
- If the above process doesn't succeed please try again with the micro usb port

Also I don't remember if in one of your previous attempts (of any combination) if you tried to connect your power adaptor immediately after burning starts.

[marine_tugah]

Please do all the above !!!
After that you can also try these 2 firmwares : https://cloud.mail.ru/public/38G1/43AVER7CL and https://yadi.sk/d/QhKwMsbi5dNB0w (just in case and if you didn't already tried them)

I do tried the both roms and same result! I made another video!

[marine_tugah]

By the above you mean that you tried Both the otg port AND the black USB port? Correct?
Let me also tell you that according to my information there may be boxes like yours (H9 X3) that have 2G rom while they are advertised as 4G !!!! There are even some which have 1G instead of 4G !!!! These peculiarities may explain why for some people with the same box as yours one method works and for others not.
The 1st rom I gave you is if you have 2G and the 2nd is if you have 1G.
Inside the log you send there is a line "low power". A message like that may be when your cable is too long (the best could be something like 10-20 cm) or not enough power from the PC/laptop port etc. In such a case you may try another PC USB port and also to connect the Power adapter immediately when burning starts.

Yes sir the blue (usb 3.0 port) is not reconized by computer! the micro usb (otg port) and the usb type a 2.0 por is reconized by computer but allways same error. I tried diferent cablets and diferent usb ports a diferent computer I have a b450 ryzen msi motherboard with good quality usb ports and still same problem!

[ath156]

Please do all the above !!!
After that you can also try these 2 firmwares : https://cloud.mail.ru/public/38G1/43AVER7CL and https://yadi.sk/d/QhKwMsbi5dNB0w (just in case and if you didn't already tried them)

[ath156]

I allready try the roms with otg port normal port and still no luck

By the above you mean that you tried Both the otg port AND the black USB port? Correct?
Let me also tell you that according to my information there may be boxes like yours (H9 X3) that have 2G rom while they are advertised as 4G !!!! There are even some which have 1G instead of 4G !!!! These peculiarities may explain why for some people with the same box as yours one method works and for others not.
The 1st rom I gave you is if you have 2G and the 2nd is if you have 1G.
Inside the log you send there is a line "low power". A message like that may be when your cable is too long (the best could be something like 10-20 cm) or not enough power from the PC/laptop port etc. In such a case you may try another PC USB port and also to connect the Power adapter immediately when burning starts.

[marine_tugah]

[04:23:10 776][HUB2-1][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x00000960
[04:23:10 838][HUB2-1][Inf]--Connect path=Controlador Anfitrião Compatível Com USB xHCI/P0/P0
[04:23:10 838][HUB2-1][Inf]--Start burning...
[04:23:10 901][HUB2-1][Inf]--------------ERASE BOOTLOADER------------
[04:23:10 901][HUB2-1][Inf]-------------Download DDR.USB-----------
[04:23:10 902][HUB2-1][Inf]--0-7-0-16
[04:23:10 902][HUB2-1][Inf]--Upload encrypt at 0xff800228
[04:23:10 919][HUB2-1][Inf]--ulValue = 0xa0f83180
[04:23:10 919][HUB2-1][Inf]--No need download
[04:23:10 920][HUB2-1][Inf]--0-7-0-16-0-0-0-0
[04:23:10 920][HUB2-1][Inf]--No need download
[04:23:10 920][HUB2-1][Inf]-- low_power
[04:23:10 926][HUB2-1][Inf]--Send command success
[04:23:10 929][HUB2-1][Inf]--Read command status success
[04:23:10 929][HUB2-1][Inf]-------------Download meson1.dtb-----------
[04:23:10 930][HUB2-1][Inf]--0-7-0-16
[04:23:10 930][HUB2-1][Inf]--Enc(0xa0f83180)
[04:23:10 930][HUB2-1][Inf]-- download mem dtb normal 67710
[04:23:10 930][HUB2-1][Inf]--Send download command success
[04:23:10 943][HUB2-1][Inf]--Read command status success
[04:23:10 955][HUB2-1][Inf]--Transfer complete
[04:23:10 955][HUB2-1][Inf]--Send download get_status command succeed
[04:23:10 959][HUB2-1][Inf]--get_status success
[04:23:11 467][HUB2-1][Inf]-------------ERASE FLASH-----------
[04:23:13 482][HUB2-1][Inf]--send command diskinit
[04:23:13 482][HUB2-1][Inf]--disk_initial 0
[04:23:13 482][HUB2-1][Inf]--Send command success
[04:23:14 211][HUB2-1][Err]--usb_reap_async_nocancel Try 2 time! ret=-5 Timeout= 30
, usbReadFile len 512 to read, ret=-5 error_msg=libusb0-dll:err [_usb_reap_async] reaping request failed, win error: Um dispositivo ligado ao sistema não está a funcionar.


[04:23:14 211][HUB2-1][Inf]--Read command diskinit status
[04:23:14 211][HUB2-1][Err]--Check command return failed
[04:23:14 212][HUB2-1][Err]--[0x32030201]Uboot/Get result/DiskInitial error
[04:23:14 212][HUB2-1][Inf]--Close device handle 0x00000960
[04:23:14 425][Global][Inf]--Catch DBT_DEVICEREMOVECOMPLETE
[04:23:14 426][Global][Inf]--Scan usb device
[04:23:14 426][Global][Inf]--Aml scan WorldCup Device
[04:23:14 426][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:14 426][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_43d5&subsys_11421b21& rev_01#4&2c18e2e3&0&000b#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:14 426][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&4087d53&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:14 426][Global][Inf]-------->[Port0]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port1]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port5]Other device
[04:23:14 426][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port8]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port9]NoDeviceConnected
[04:23:14 426][Global][Inf]-------->[Port10]NoDeviceConnected
[04:23:14 427][Global][Inf]-------->[Port11]Other device
[04:23:14 427][Global][Inf]-------->[Port12]Other device
[04:23:14 427][Global][Inf]-------->[Port13]NoDeviceConnected
[04:23:14 427][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:14 427][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_149c&subsys_7c021462& rev_00#4&3af4ccd4&0&0341#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:14 427][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&1f32783&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:14 427][Global][Inf]-------->[Port0]NoDeviceConnected
[04:23:14 427][Global][Inf]-------->[Port1]Other device
[04:23:14 427][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:14 427][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:14 427][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:14 427][Global][Inf]-------->[Port5]NoDeviceConnected
[04:23:14 428][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:14 428][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:14 428][Global][Inf]--Scan USB host controller complete
[04:23:14 428][Global][Inf]--Update data center with HubMap
[04:23:14 428][Global][Inf]--Update hub2 device data
[04:23:14 428][Global][Inf]--Update HUB2-1
[04:23:14 428][HUB2-1][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-2
[04:23:14 428][HUB2-2][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-3
[04:23:14 428][HUB2-3][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-4
[04:23:14 428][HUB2-4][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-5
[04:23:14 428][HUB2-5][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-6
[04:23:14 428][HUB2-6][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-7
[04:23:14 428][HUB2-7][Inf]--Update device path
[04:23:14 428][Global][Inf]--Update HUB2-8
[04:23:14 428][HUB2-8][Inf]--Update device path
[04:23:14 428][Global][Inf]--Scan end
[04:23:14 636][Global][Inf]--Catch DBT_DEVICEARRIVAL
[04:23:14 636][Global][Inf]--Scan usb device
[04:23:14 636][Global][Inf]--Aml scan WorldCup Device
[04:23:14 636][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:14 637][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_43d5&subsys_11421b21& rev_01#4&2c18e2e3&0&000b#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:14 637][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&4087d53&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:14 637][Global][Inf]-------->[Port0]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port1]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port5]Other device
[04:23:14 637][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port8]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port9]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port10]NoDeviceConnected
[04:23:14 637][Global][Inf]-------->[Port11]Other device
[04:23:14 637][Global][Inf]-------->[Port12]Other device
[04:23:14 637][Global][Inf]-------->[Port13]NoDeviceConnected
[04:23:14 638][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:14 638][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_149c&subsys_7c021462& rev_00#4&3af4ccd4&0&0341#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:14 638][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&1f32783&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:14 638][Global][Inf]-------->[Port0]\\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
[04:23:14 638][Global][Inf]-------->[Port1]Other device
[04:23:14 638][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:14 638][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:14 638][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:14 638][Global][Inf]-------->[Port5]NoDeviceConnected
[04:23:14 638][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:14 638][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:14 638][Global][Inf]--Scan USB host controller complete
[04:23:14 638][Global][Inf]--Update data center with HubMap
[04:23:14 638][Global][Inf]--Update hub2 device data
[04:23:14 638][Global][Inf]--Update HUB2-1 \\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
[04:23:14 638][HUB2-1][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-2
[04:23:14 638][HUB2-2][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-3
[04:23:14 638][HUB2-3][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-4
[04:23:14 638][HUB2-4][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-5
[04:23:14 638][HUB2-5][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-6
[04:23:14 638][HUB2-6][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-7
[04:23:14 638][HUB2-7][Inf]--Update device path
[04:23:14 638][Global][Inf]--Update HUB2-8
[04:23:14 638][HUB2-8][Inf]--Update device path
[04:23:14 638][Global][Inf]--Scan end
[04:23:14 700][Global][Inf]--Burning thread HUB2-1 start
[04:23:14 763][HUB2-1][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x00000d34
[04:23:14 824][HUB2-1][Inf]--Connect path=Controlador Anfitrião Compatível Com USB xHCI/P0/P0
[04:23:14 824][HUB2-1][Inf]--Start burning...
[04:23:14 886][HUB2-1][Inf]--------------ERASE BOOTLOADER------------
[04:23:14 886][HUB2-1][Inf]-------------Download DDR.USB-----------
[04:23:14 886][HUB2-1][Inf]--3-2-0-0
[04:23:14 886][HUB2-1][Inf]--Control write pll reg1 0xfffa0000:0x000000b1
[04:23:15 388][HUB2-1][Inf]--Control write pll reg1 0xfffa0000:0x00005183
[04:23:15 898][HUB2-1][Inf]--Control write pll reg1 0xfffa0000:0x000000b1
[04:23:16 413][HUB2-1][Inf]--Control write pll reg1 0xfffa0000:0x00005183
[04:23:16 928][HUB2-1][Inf]--Write initial succeed
[04:23:16 928][HUB2-1][Inf]--Upload encrypt at 0xff800228
[04:23:16 929][HUB2-1][Inf]--ulValue = 0xa0f83180
[04:23:16 929][HUB2-1][Inf]--Read encrypt value succeed
[04:23:16 929][HUB2-1][Inf]--Download DDR.USB,size: 65536!
[04:23:16 938][HUB2-1][Inf]--Transfer complete 65536
[04:23:16 938][HUB2-1][Inf]--Run at address 0xfffa0000
[04:23:16 938][HUB2-1][Inf]--RunInRam success
[04:23:16 988][HUB2-1][Inf]--0-0-1-8-0-1-0-0
[04:23:16 988][HUB2-1][Inf]--CheckFileRunState return 1-8
[04:23:16 988][HUB2-1][Inf]--0-0-1-8-0-1-0-0
[04:23:16 988][HUB2-1][Inf]--G12 init
[04:23:16 988][HUB2-1][Inf]--Get Encrpt ulValue = 0xa0f83180
[04:23:16 988][HUB2-1][Inf]--Have Semaphore
[04:23:16 988][HUB2-1][Inf]--Download BL2
[04:23:16 988][HUB2-1]Aml_Libusb_bl2_boot2 start!
[04:23:16 990][HUB2-1]sequence= 0, datasize= 16384, fipOffset= 65536
[04:23:16 998][HUB2-1]sequence= 1, datasize= 49152, fipOffset= 393216
[04:23:17 003][HUB2-1]sequence= 2, datasize= 16384, fipOffset= 229376
[04:23:17 011][HUB2-1]sequence= 3, datasize= 49152, fipOffset= 81920
[04:23:17 036][HUB2-1]sequence= 4, datasize= 16384, fipOffset= 65536
[04:23:17 043][HUB2-1]sequence= 5, datasize= 49152, fipOffset= 393216
[04:23:17 047][HUB2-1]sequence= 6, datasize= 16384, fipOffset= 229376
[04:23:17 056][HUB2-1]sequence= 7, datasize= 49152, fipOffset= 180224
[04:23:17 123][HUB2-1]sequence= 8, datasize= 16384, fipOffset= 65536
[04:23:17 230][HUB2-1]sequence= 9, datasize= 1248112, fipOffset= 81920
[04:23:17 280]BL2 END, waiting TPL plug-in...
[04:23:17 280][HUB2-1]cmd end
[04:23:17 280][HUB2-1]Aml_Libusb_bl2_boot2 end!
[04:23:17 280][HUB2-1][Inf]--Release Semaphore
[04:23:18 500][Global][Inf]--Catch DBT_DEVICEREMOVECOMPLETE
[04:23:18 500][Global][Inf]--Scan usb device
[04:23:18 500][Global][Inf]--Aml scan WorldCup Device
[04:23:18 501][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:18 501][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_43d5&subsys_11421b21& rev_01#4&2c18e2e3&0&000b#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:18 501][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&4087d53&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:18 501][Global][Inf]-------->[Port0]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port1]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port5]Other device
[04:23:18 501][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port8]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port9]NoDeviceConnected
[04:23:18 501][Global][Inf]-------->[Port10]NoDeviceConnected
[04:23:18 502][Global][Inf]-------->[Port11]Other device
[04:23:18 502][Global][Inf]-------->[Port12]Other device
[04:23:18 502][Global][Inf]-------->[Port13]NoDeviceConnected
[04:23:18 502][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:18 502][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_149c&subsys_7c021462& rev_00#4&3af4ccd4&0&0341#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:18 502][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&1f32783&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:18 502][Global][Inf]-------->[Port0]NoDeviceConnected
[04:23:18 502][Global][Inf]-------->[Port1]Other device
[04:23:18 503][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:18 503][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:18 503][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:18 503][Global][Inf]-------->[Port5]NoDeviceConnected
[04:23:18 503][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:18 503][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:18 503][Global][Inf]--Scan USB host controller complete
[04:23:18 503][Global][Inf]--Update data center with HubMap
[04:23:18 503][Global][Inf]--Update hub2 device data
[04:23:18 503][Global][Inf]--Update HUB2-1
[04:23:18 503][HUB2-1][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-2
[04:23:18 503][HUB2-2][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-3
[04:23:18 503][HUB2-3][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-4
[04:23:18 503][HUB2-4][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-5
[04:23:18 503][HUB2-5][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-6
[04:23:18 503][HUB2-6][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-7
[04:23:18 503][HUB2-7][Inf]--Update device path
[04:23:18 503][Global][Inf]--Update HUB2-8
[04:23:18 503][HUB2-8][Inf]--Update device path
[04:23:18 503][Global][Inf]--Scan end
[04:23:18 531][HUB2-1][Inf]--Device is removed
[04:23:19 873][Global][Inf]--Catch DBT_DEVICEARRIVAL
[04:23:19 874][Global][Inf]--Scan usb device
[04:23:19 874][Global][Inf]--Aml scan WorldCup Device
[04:23:19 874][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:19 874][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_43d5&subsys_11421b21& rev_01#4&2c18e2e3&0&000b#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:19 874][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&4087d53&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:19 874][Global][Inf]-------->[Port0]NoDeviceConnected
[04:23:19 874][Global][Inf]-------->[Port1]NoDeviceConnected
[04:23:19 874][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:19 874][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:19 874][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:19 875][Global][Inf]-------->[Port5]Other device
[04:23:19 875][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:19 875][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:19 875][Global][Inf]-------->[Port8]NoDeviceConnected
[04:23:19 875][Global][Inf]-------->[Port9]NoDeviceConnected
[04:23:19 875][Global][Inf]-------->[Port10]NoDeviceConnected
[04:23:19 875][Global][Inf]-------->[Port11]Other device
[04:23:19 875][Global][Inf]-------->[Port12]Other device
[04:23:19 875][Global][Inf]-------->[Port13]NoDeviceConnected
[04:23:19 876][Global][Inf]--Host: Controlador Anfitrião Compatível Com USB xHCI
[04:23:19 876][Global][Inf]--DevPath:\\?\pci#ven_1022&dev_149c&subsys_7c021462& rev_00#4&3af4ccd4&0&0341#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[04:23:19 876][Global][Inf]---->Roothub:USB#ROOT_HUB30#5&1f32783&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[04:23:19 876][Global][Inf]-------->[Port0]\\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
[04:23:19 876][Global][Inf]-------->[Port1]Other device
[04:23:19 876][Global][Inf]-------->[Port2]NoDeviceConnected
[04:23:19 876][Global][Inf]-------->[Port3]NoDeviceConnected
[04:23:19 876][Global][Inf]-------->[Port4]NoDeviceConnected
[04:23:19 876][Global][Inf]-------->[Port5]NoDeviceConnected
[04:23:19 876][Global][Inf]-------->[Port6]NoDeviceConnected
[04:23:19 876][Global][Inf]-------->[Port7]NoDeviceConnected
[04:23:19 876][Global][Inf]--Scan USB host controller complete
[04:23:19 876][Global][Inf]--Update data center with HubMap
[04:23:19 876][Global][Inf]--Update hub2 device data
[04:23:19 876][Global][Inf]--Update HUB2-1 \\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
[04:23:19 876][HUB2-1][Inf]--Update device path
[04:23:19 876][Global][Inf]--Update HUB2-2
[04:23:19 876][HUB2-2][Inf]--Update device path
[04:23:19 876][Global][Inf]--Update HUB2-3
[04:23:19 876][HUB2-3][Inf]--Update device path
[04:23:19 876][Global][Inf]--Update HUB2-4
[04:23:19 876][HUB2-4][Inf]--Update device path
[04:23:19 877][Global][Inf]--Update HUB2-5
[04:23:19 877][HUB2-5][Inf]--Update device path
[04:23:19 877][Global][Inf]--Update HUB2-6
[04:23:19 877][HUB2-6][Inf]--Update device path
[04:23:19 877][Global][Inf]--Update HUB2-7
[04:23:19 877][HUB2-7][Inf]--Update device path
[04:23:19 877][Global][Inf]--Update HUB2-8
[04:23:19 877][HUB2-8][Inf]--Update device path
[04:23:19 877][Global][Inf]--Scan end
[04:23:19 910][HUB2-1][Inf]--Device is connected
[04:23:19 910][HUB2-1][Inf]--Close device handle 0x00000d34
[04:23:19 973][HUB2-1][Inf]--Open device handle \\?\usb#vid_1b8e&pid_c003#6&976cc38&0&1#{a5dcbf10-6530-11d2-901f-00c04fb951ed} 0x00000d2c
[04:23:23 036][HUB2-1][Inf]--0-7-0-16
[04:23:23 036][HUB2-1][Inf]--CheckFileRunState succeed
[04:23:23 037][HUB2-1][Inf]-- low_power
[04:23:23 042][HUB2-1][Inf]--Send command success
[04:23:23 045][HUB2-1][Inf]--Read command status success
[04:23:23 045][HUB2-1][Inf]-------------Download meson1.dtb-----------
[04:23:23 046][HUB2-1][Inf]--0-7-0-16
[04:23:23 046][HUB2-1][Inf]--Enc(0xa0f83180)
[04:23:23 046][HUB2-1][Inf]-- download mem dtb normal 67710
[04:23:23 046][HUB2-1][Inf]--Send download command success
[04:23:23 060][HUB2-1][Inf]--Read command status success
[04:23:23 071][HUB2-1][Inf]--Transfer complete
[04:23:23 071][HUB2-1][Inf]--Send download get_status command succeed
[04:23:23 075][HUB2-1][Inf]--get_status success
[04:23:23 583][HUB2-1][Inf]-------------ERASE FLASH-----------
[04:23:25 596][HUB2-1][Inf]--send command diskinit
[04:23:25 596][HUB2-1][Inf]--disk_initial 0
[04:23:25 596][HUB2-1][Inf]--Send command success
[04:23:26 028][HUB2-1][Err]--failed:[04:23:26 028][HUB2-1][Inf]--Read command diskinit status
[04:23:26 028][HUB2-1][Err]--Check command return failed
[04:23:26 031][HUB2-1][Err]--[0x32030201]Uboot/Get result/DiskInitial error
[04:23:26 031][HUB2-1][Inf]--Close device handle 0x00000d2c

Heere is the log

[marine_tugah]

OK. I think I have new information about your box and what might be happening. Please try the following:
1. Download this firmware https://mega.nz/file/VCZ3FKbI#Op6KXE...vFBunQ3YcqM7k0
2. Use the "short pin" method
3. First try with the micro usb cable and if this is not successfull please also try with a USB-A/USB-A cable to the Black USB port

If the above does't restore your box, please download this firmware and repeat the above steps https://drive.google.com/file/d/1u61...4EwYoOw9X/view

Please report results in any case. Good Luck.

I allready try the roms with otg port normal port and still no luck

[freddy]

There are many Methods Of Madness

When Testing

This is what worked for me

Even though USB male to male was recognized by PC

Only through OTG was i able to Read From/ Write To

Iam no expert think OTG cable is like crossover/

Or enables device to be slave or master...

Host or guest..

Something like that....

Happy Testing

[freddy]

Okay

Iam a little confused...

You tested one cable on OTG port and PC recognized it?

If you heard the sound/prompt from windows.

That would be a good thing!!!!

Unplug OTG cable from PC

No open up utility

Hold in reset button

Plug in cable to PC

[marine_tugah]

With the otg only? i only tested 1 cable on otg port but since computer reconized the board i thought that is not cable fault. I have more cables that I can use to test on otg port!

[freddy]

I tried the micro usb port and have no luck either!

Stay with Micro / OTG port..
Have tested similar board only OTG cable worked

Tested 5 different cables,finally an older charging cable from samsung phone worked.

[ath156]

Sorry, OK now I can see it. Forget what I said.

[ath156]

I got a message that you quoted me, but I can see nothing. In case the spam bot blocked your post it is better to write a new one and not to wait for the approval of the old one !!!!!

[marine_tugah]

OK. I think I have new information about your box and what might be happening. Please try the following:
1. Download this firmware https://mega.nz/file/VCZ3FKbI#Op6KXE...vFBunQ3YcqM7k0
2. Use the "short pin" method
3. First try with the micro usb cable and if this is not successfull please also try with a USB-A/USB-A cable to the Black USB port

If the above does't restore your box, please download this firmware and repeat the above steps https://drive.google.com/file/d/1u61...4EwYoOw9X/view

Please report results in any case. Good Luck.

I will try this tonight tank you!