[0x32030201]Uboot/Get result/DiskInitial error

[hakie09]

i have the same problem, couldn't flash it and always stop at 7% on usb burning tool. but i have tried 1 firmware (S905XQ4_V1.0) it was successfully, but when i turn on the tv box. still has the same. any suggestions?

[f0x]

Hello .. its hk1box .. where its shortpin this card. Thanks

[ath156]

Hello .. its hk1box .. where its shortpin this card. Thanks

Try these pins:

[f0x]

Try these pins:

Thank you. But i dont understand. ? I think something is missing.

[ath156]

Thank you. But i dont understand. ? I think something is missing.

What is miising ??? Didn't you see 2 red arrows pointing to the 2 pins to short? You need something else?

[f0x]

What is miising ??? Didn't you see 2 red arrows pointing to the 2 pins to short? You need something else?

I cant see your photos

[ath156]

I cant see your photos

https://postimg.cc/N5x71GCQ

[f0x]

Oh thanks. I see now. I try it. But dont reaction device. I think my device dead

[ath156]

Oh thanks. I see now. I try it. But dont reaction device. I think my device dead

How long is the USB-A/USB-A cable you are using? Did you buy it or did you make it yourself?

[f0x]

I have this problem.
my device has became very slow.
And image frozen. And i used power off/ on I try recovery button Later its dont open
I try flash firmware and its error %7 formating....
error code 0x32030201 uboot/ get result / diskinitial error
Try flash firmware again used shortpin but its same error.

Thanks for help

[ath156]

I have this problem.
my device has became very slow.
And image frozen. And i used power off/ on I try recovery button Later its dont open
I try flash firmware and its error %7 formating....
error code 0x32030201 uboot/ get result / diskinitial error
Try flash firmware again used shortpin but its same error.

Thanks for help

If you want try to install my custom firmware from here: https://forum.freaktab.com/forum/tv-...amlogic-s905x3
- follow the instructions
- use UBT 2.2 (do not forget the licence folder !!)
- use a short USB-A/USB-A cable (better less than 30cm long)

[f0x]

If you want try to install my custom firmware from here: https://forum.freaktab.com/forum/tv-...amlogic-s905x3
- follow the instructions
- use UBT 2.2 (do not forget the licence folder !!)
- use a short USB-A/USB-A cable (better less than 30cm long)

Okey. I try it. Thanks again.

[ath156]

Okey. I try it. Thanks again.

And something very important that I forgot to ask you. When did you buy this HK1 Box ???
Because in the past 1-2 months there were some HK1 Boxes sold with only 100Mbps Lan, while all other TVboxes of this "family" have 1.000Mbps Lan !!!!!
HK1 Box with 100Mbps Lan need special firmware.

[f0x]

And something very important that I forgot to ask you. When did you buy this HK1 Box ???
Because in the past 1-2 months there were some HK1 Boxes sold with only 100Mbps Lan, while all other TVboxes of this "family" have 1.000Mbps Lan !!!!!
HK1 Box with 100Mbps Lan need special firmware.

Last 1 mounth. Its 100m
and i try your custom firmware its same error %7 uboot/get result/ diskintial error

[ath156]

Last 1 mounth. Its 100m
and i try your custom firmware its same error %7 uboot/get result/ diskintial error

That should have been the 1st thing to tell !!!!!!!!! That's why anybody with any problem should describe in detail his TVbox and the problem !. All firmwares for 1GB Lan are incompatible with your TVbox !
Anyway.
Download and install the following firmware (in the usual way - probably you won't even need to short the 2 pins !!).

https://drive.google.com/drive/folders/1ev-w2pT203U-lHt9nfGc5W78Sr9Vo98_

Good luck.