[0x32030201]Uboot/Get result/DiskInitial error

[halitv]

I have an identical box, how can I make a backup, complete with ROM?

[halitv]

Hi, I'm struggling with this too, did you find a rom for it?
none of them gives a good error:
[23:24:38 380][HUB4-3][Inf]--Failure : 3, FailureMax : 3
[23:24:38 411][HUB4-3][Err]--[0x10103003]Romcode/Initialize DDR/Download buffer/USB transfer error
[23:24:38 411][HUB4-3][Inf]--Close device handle 0x000006e4



KLM8G1GETF-B041

Magyar Telekom TV SmartBox - Android TV Guide (androidtv-guide.com)

[SSimon]

I have been using W95 S905W android box since early 2018. Over that time, I have tested multiple firmware on it and all the compatible ones have worked without issues. Eventually, I reverted to the stock and used it for about 2 years. One day, I noticed lagging on the device and decided to reboot it but it didn't power on. Since September last year, I've been trying to flash the stock rom and the rest that had worked before but I have not succeeded. I'm getting the error uboot/get result/diskinitial always at 7%. The box is successfully connecting to my computer even without pressing the reset button. Does anyone have a solution to this problem? Thanks.

[smithyjanie]

I have flashed my T95Q many times and have faced this issue a lot. The solution I found is you need the adapter too.

You have to plug in the AC Adapter and USB cable at the SAME TIME. While the burning tool is running, select your image, press Start. Then you may have to try this combo few times to get it right. Just unplug and plug in at the same time until it goes to flashing correctly.

[herr_marechal]

Hi guys anybody know how to downgrade android 9 from slimbox to stock box android 7. Well all times stop on 7% uboot error on amlogic tools. I try by twrp and it say error about try install p212(android 7). How to force install?
My tx9pro is s912
3gb lddr3
32gb THGBMFG8C4LBAIR

[cya nomore]

same issue eccept an MXQ PRO 4K I think I need V.S905W firmware

[f0x]

This must be the "official" firmware for HK1 Box with 100M Lan !!!! https://drive.google.com/drive/folde...56193e5fQkAMBY

(and it is funny that we keep talking about a S905X3 box in the S905X2 thread !!).

Thanks a lot. I try this firmware. But give same error.
used ubt 2.1.7.1 and 2.2.0
USed 2 cable
Used shortpin method and normal method andd Click in ubt erase normal method and erase all method and
Click erase bootloader and dont click erase bootloader
All try give me same error .. i dont understand device problem

[ath156]

This must be the "official" firmware for HK1 Box with 100M Lan !!!! https://drive.google.com/drive/folde...56193e5fQkAMBY

(and it is funny that we keep talking about a S905X3 box in the S905X2 thread !!).

[f0x]

copy license file in UBT, and as last try - flash with attached power cord ...

I try it. Give same error this way. Thanks

...I follow your correct procedure for differents 4 USB at my laptop...

copy license file in UBT, and as last try - flash with attached power cord ...

[f0x]

Thanks information..
This my box sticker And

https://ibb.co/XjZ0sBd

I use 2 cable in picture and i will try make new cable
I follow your correct procedure for differents 4 USB at my laptop... but error alltimes flashing %7 and time : 1:10 uboot/get result/ diskinitial error

[ath156]

If you have 2 spare/old/useless cables (from old smartphones, printers, etc) you can use them to make a DIY cable. Cut them and keep only the USB-A part of them. Connect the 4 inner and thinner cables color to color. Insulate the connections. Better make it no longer than 15cm.

The cable you already have (60cm) is not too long but as being more than 30cm, it may still give you trouble, due to wire resistance (not enough power to "burn" the firmware?). So if you can make a DIY cable you may eliminate this factor (if it exists of course). Also I don't remember if I told you to try different USB ports of your PC/Laptop and only the USB2.0 port of the TVbox.

I repeat the correct procedure (not the one with shorting the 2 pins):
- Start UBT version 2.2. Load the firmware and press "START"
- Connect one end of the cable to the USB port of your PC/Laptop
- While pressing the reset button (centrically into the AV port) at the same time connect the other end of the cable to the USB 2.0 port of the box (the black one). After the burning process starts stop pressing the reset button.

******Use only the firmware which is for 100Mbps lan (if your box is with 100Mbps lan)

[f0x]

I try these firmwares. And i used ubt 2.1.6.8/2.1.7.1/2.2.0
and i did short pin sometimes use recovery button.
all try same error.

Andd...
??????i try burn card maker for sdkart Power on hold reco button.
device not reaction

[f0x]

If your HK1 Box is with the 100Mbps Lan (as the sticker at the bottom states) this is the correct firmware.
You never answered my question. How long is the cable you are using??? Did you make it yourself or did you buy it?

Its USB 2.0/3.0 HDD data cable.usb.a to USB.a ( 60cm)

[ath156]

Same error 100m firmware

If your HK1 Box is with the 100Mbps Lan (as the sticker at the bottom states) this is the correct firmware.
You never answered my question. How long is the cable you are using??? Did you make it yourself or did you buy it?