Bricked H96 Max 8k Ultra HD board XYX_S905X3

[Tabango]

Hello ,

My box it's bricked .

I just have the red led that lights up and impossible to reconnect with usb male male cable
I also tried to use the reset button in the AV hole.
If a person has already had this and they have a solution ..
Thank you in advance .

[ath156]

Try this

[Tabango]

Thank you for your answer ...
I have to make a bridge between its 2 points ok.
I must do this by also pressing the reset button and then turn on the power?
What is the exact precaution to follow so as not to do anything stupid. ?
Thank you

[ath156]

No.Leave the box bare then short the pins and then connect with cable usba usba.Before that start the usb burning tool.sorry but i am outside now.

[Tabango]

Hi again ... very thanks ath156.

My box is resurrected.

Process it's simple:
1) Launch the USB Burning tool program and load the original image file and then click on start
2) Make a bridge between the points indicated on the motherboard of the box
3) Connect USB (male-male) to BOX
4) Press and hold the reset button in the hole of the AV socket
5) Connect USB (male-male) to PC
6) And that's it wait 100% burned sucessfuly
7) Disconnect box
8) Remove bridge
9) Connect box to TV (HDMI + power)

If after connecting your box nothing happens after 15 seconds disconnect the power supply wait 10 seconds and reconnected.
After, be patient 10 minutes for all this recharge ...

If this can help you.
Thanks again to ath156

[ath156]

Yes that's the exact procedure.
Sorry but as I already told you I was out for the daily exercise (due to the coronovirus restrictions) so my post was from my phone and of course very short (with no details).
Happy for you and your revived box !!!

Edit: I think that maybe step 4) actually is not needed (not crucial). Shorting the 2 pins does the trick.On the other hand it is good practice to leave your box for some minutes (3-4 minutes) without any power and then begin the procedure (so the system will be completely "empty" of any residual current).

[Chet812]

Hi again ... very thanks ath156.

My box is resurrected.

Process it's simple:
1) Launch the USB Burning tool program and load the original image file and then click on start
2) Make a bridge between the points indicated on the motherboard of the box
3) Connect USB (male-male) to BOX
4) Press and hold the reset button in the hole of the AV socket
5) Connect USB (male-male) to PC
6) And that's it wait 100% burned sucessfuly
7) Disconnect box
8) Remove bridge
9) Connect box to TV (HDMI + power)

If after connecting your box nothing happens after 15 seconds disconnect the power supply wait 10 seconds and reconnected.
After, be patient 10 minutes for all this recharge ...

If this can help you.
Thanks again to ath156

Can you please shared the link to the image file you used to flash? Pretty please?

[ath156]

Can you please shared the link to the image file you used to flash? Pretty please?

Why you are not using the last official one? https://drive.google.com/drive/folde...-TPyiK236-Hu1f

[ibrahimatay]

My tv box (H96 MAX X3) is bricked too. But I can't download the photos of your answer. Can you upload this again?

[ibrahimatay]

Or please send to my e-mail ([email protected])

[ath156]

My tv box (H96 MAX X3) is bricked too. But I can't download the photos of your answer. Can you upload this again?

Here are the 2 points to short both if you have GREEN or BLUE board.


Good Luck

[ibrahimatay]

Here are the 2 points to short both if you have GREEN or BLUE board.


Good Luck

Thank you for all. I try this. I connect internet from Turkey and firstly I could not saw them. Finally, I can see your attachments via proxyfree site.

Piranha8032 cihaz?mdan Tapatalk kullan?larak gönderildi

[ibrahimatay]

I followed the steps that reported by Tabango. My computer recognized the box (h96 max x3-blue mainboard), which was not recognized by the computer for 2 months and remained constant in the red light and loaded the rom as if miracle. Thank you again Ath156 and Tabango.

[azumibg]

cool

[figu]

I followed the steps that reported by Tabango. My computer recognized the box (h96 max x3-blue mainboard), which was not recognized by the computer for 2 months and remained constant in the red light and loaded the rom as if miracle. Thank you again Ath156 and Tabango.

?brahim Nas?l yapt???n? Bana da söyler misin Ayn? sorun bende de var