Announcement
Collapse
No announcement yet.
Announcement
Collapse
No announcement yet.
Unable to connect S905X3 to Laptop
Collapse
X
-
Hi, I have similar problem that you had originally. When I plug the device it is connected 2 to 3 seconds and then it disconnects.
What you did to fix the original problem. My device is Sunnzo S9 Max 4GB+64. I did pretty much everything described here but it still continues to disconnect after 2 to 3 seconds. My cable is brand new factory made 50 cm male-male cable.
I did first firmware upgrade successfully, even on that first attempt I had the same problem but after laptop restart it was finally ok.
But now its like this, see details in this video https://www.youtube.com/watch?v=zuOvlGppwhQ For some reason the Windows sound of device connected and disconnected are not playing well in the video. I can't find a way to fix it again.
Edit: Solution: Keep the button pressed longer...
-
In our city, they sold good set-top boxes for television, and my device did not work as well as yours. I read on the Internet that the problem was in the port to which I connected it. Too new, according to the version I had a port, I had to flash the device. I heard that it works more effectively, recently I read an article about it. It is best to try to contact a specific reference book in order to learn more about the problem. I usually use a blog https://gadgetguide.in when it comes to some software or hardware problems. When there are problems with the technique, I am already used to using guides, in which everything is carefully described. I think your topic will be found there and you will be able to solve it in a short time.Last edited by Fany2021; 02-22-2021, 01:57.
Leave a comment:
-
Hmmmmmmmmmmmmmmmmmmmmmm
If you just got it out of the box
Why are you even trying to connect to PC
Was it bricked out of the box?
Youve allready tested the factory rom and it sucks that bad?
Try this maybe
Connect to TV see if you have video
Try the toothpick thing and see if you can boot to recovery
If successful
Wipe cache partition
Wipe data factory reset
Reboot
Leave a comment:
-
Originally posted by abhi2020 View Postwhen i am trying to copy the img file to the license folder, its asking me to give windows permission to copy. do you think its windows permissions error ?
but i see that logs are being generated ( written to the folder)
i have around 12 feet usb to usb a cable. is the cable culprit ?
You start USB burning tool and then you load there the .img file.After that you press "start".
And of course the cable must be much shorter than 1 meter as already Guest told you. In my opinion it is better to be shorter than 30cm (or 15cm best).Otherwise you can get a "low power" error message in UBT.
You can very easily make a new cable by yourself. All you need is 2 cables from old phones etc. You cut them keeping only the USB-A and a short cable. These 2 cables you connect them color to color (red to red/ and black to black) and there is your new cable !!
Leave a comment:
-
when i am trying to copy the img file to the license folder, its asking me to give windows permission to copy. do you think its windows permissions error ?
but i see that logs are being generated ( written to the folder)
i have around 12 feet usb to usb a cable. is the cable culprit ?
Leave a comment:
-
There is a whole Topic here about your box (with firmwares, how to short pins etc) https://forum.freaktab.com/forum/tv-...0-media-player
First try different roms.
If you finally decide to open your box look at post #194 if you have the same/similar board.
Leave a comment:
-
Originally posted by abhi2020 View Posti did what you told me. i tried various methods. even i tried like what you mentioned
i have loaded the .img file, and press start on the usb burning tool. then i have connected the cable to my box, pressed reset button using toothpick and then connected the usb cable to my laptop
i am getting the same issue after 8%
[HUB1-2][Err]--Download init command failed
[HUB1-2][Err]--[0x]Romcode/Lead UBOOT/Identify/USB Control setup error
do you want me to send the full log file ?
Also try this (sometimes it helps). When it stops at 8% just Unplug and Replug the USB cable (without doing anything else). Sometimes it continues the burning process, but if you have the wrong firmware .................
Leave a comment:
-
i did what you told me. i tried various methods. even i tried like what you mentioned
i have loaded the .img file, and press start on the usb burning tool. then i have connected the cable to my box, pressed reset button using toothpick and then connected the usb cable to my laptop
i am getting the same issue after 8%
[HUB1-2][Err]--Download init command failed
[HUB1-2][Err]--[0x]Romcode/Lead UBOOT/Identify/USB Control setup error
do you want me to send the full log file ?
Leave a comment:
-
Originally posted by abhi2020 View PostOh i am sorry. i thought i have specified the model number
below is the model number
Amlogic S905X3 X96 Air
I have installed amlogic usb tool 2.2.0, open the tool, inserted the img file, then inserted the toothpick to the device, and started the device with usb a to usb a cable connected to my laptop and the device
after i connected, it is shows an connected in the tool
when i click on start, its giving me the error message
Below is the message in the log file
[HUB1-2][Err]--Download init command failed
[HUB1-2][Err]--[0x]Romcode/Lead UBOOT/Identify/USB Control setup error
1. You load the .img file and you press "START" of USB burning tool. YOU DO NOT CONNECT THE BOX WITH THE CABLE YET. Nothing is connected to the Laptop USB port YET!!!!!
2. Only after that you can connect the USB cable to the Laptop's USB port!!!!! (and of course at the same time keep pressing the reset button of the box).
Leave a comment:
-
Oh i am sorry. i thought i have specified the model number
below is the model number
Amlogic S905X3 X96 Air
I have installed amlogic usb tool 2.2.0, open the tool, inserted the img file, then inserted the toothpick to the device, and started the device with usb a to usb a cable connected to my laptop and the device
after i connected, it is shows an connected in the tool
when i click on start, its giving me the error message
Below is the message in the log file
[HUB1-2][Err]--Download init command failed
[HUB1-2][Err]--[0x]Romcode/Lead UBOOT/Identify/USB Control setup error
Leave a comment:
-
Originally posted by abhi2020 View PostHello,
i was successfully able to connect the device. but i am getting the below error while l clicked on Start
[HUB1-2][Err]--Download init command failed
[HUB1-2][Err]--[0x]Romcode/Lead UBOOT/Identify/USB Control setup error
Do you have the correct firmware/rom for your box?
Why you are not specifying the maker/model of your box? Is it a secret?
Leave a comment:
-
Hello,
i was successfully able to connect the device. but i am getting the below error while l clicked on Start
[HUB1-2][Err]--Download init command failed
[HUB1-2][Err]--[0x]Romcode/Lead UBOOT/Identify/USB Control setup error
Leave a comment:
-
Originally posted by abhi2020 View Postdevice is getting disconnected within few seconds. i am using amlogic usb tool 2.2.0 and on windows 10. do i need to conenct the device to tv and make sure i am on recovery mode in order for it not to get disconnected ?
If the burning is completed you can initialize it as usual.
Did you try different USB ports of your laptop???
Did you try both USB 2.0 and 3.0 ports of your box?
Do you have another PC to try (probably older with windows 7, although I don't think this is the problem).
Otherwise you may have to open your box to do the "short pin" method (which is a more demanding method and you have to know either what pins to connect or to find them by yourself).I think you never told us the exact model/maker of your box.
Leave a comment:
-
device is getting disconnected within few seconds. i am using amlogic usb tool 2.2.0 and on windows 10. do i need to conenct the device to tv and make sure i am on recovery mode in order for it not to get disconnected ?
Leave a comment:
-
Originally posted by abhi2020 View Postafter i download and install version 2.2.0 also same iisue
few seconds devce is getting connected to HUB1-2
but after 2 or 3 seconds device is getting disconnected from the laptop
1. Leave the box without any power (no ac adapter attached for 5-10 minutes). Leave it also bare (nothing attached to it).
2. Connect one end of USB cable to the box (the other attached to nothing).
3. Start USB burning tool, load your rom and after that press "START".
4. Press the "reset" button of your box.
5. While still pressing the reset button attach the other end to your laptop's USB. Try both 2.0 and 3.0 ports (although I think usually it is 2.0).
Good luck.
Leave a comment:
What's Going On
Collapse
There are currently 4103 users online. 4 members and 4099 guests.
Most users ever online was 16,134 at 08:28 on 08-11-2023.
Leave a comment: