If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
I tested the USER version on my EACHLINK X3 MINI Android 9.0 Smart 4K TV Box - Black 4GB DDR4 +64GB EMMC, used amlogic burning tool 2.1.7.3, unselected erase bootloader, and it flashed successfully, but after that it does not boot it is bricked.
Then I thought fine I'll flash back stock rom, I didn't erase bootloader it must be fine right?
Wrong, now the reset button method to flash it does not work, the PC does not detect the box now...
How can I save this box now?
try burn_card_maker first with your stock firmware, it can be used when the usb device does not appear on windows.
if burn card maker failed , check u-boot uart and masking the eMMC.
I tested the USER version on my EACHLINK X3 MINI Android 9.0 Smart 4K TV Box - Black 4GB DDR4 +64GB EMMC, used amlogic burning tool 2.1.7.3, unselected erase bootloader, and it flashed successfully, but after that it does not boot it is bricked.
Then I thought fine I'll flash back stock rom, I didn't erase bootloader it must be fine right?
Wrong, now the reset button method to flash it does not work, the PC does not detect the box now...
How can I save this box now?
Untick Erase bootloader at this moment does not save you from bricking the device..
Now you have to see if you have serial output then you can put the box in update mode from inside uboot, or find the emmc mask mode for that box!
I tested the USER version on my EACHLINK X3 MINI Android 9.0 Smart 4K TV Box - Black 4GB DDR4 +64GB EMMC, used amlogic burning tool 2.1.7.3, unselected erase bootloader, and it flashed successfully, but after that it does not boot it is bricked.
Then I thought fine I'll flash back stock rom, I didn't erase bootloader it must be fine right?
Wrong, now the reset button method to flash it does not work, the PC does not detect the box now...
How can I save this box now?
Ye i know... i compress them in the past then ppl complained, and i stop compressing them.. anyway i will think about it again.
Well i have a x96max s905x2 with 4GB lpddr3 and is booting just fine, you only lose the front display and to flash the box again it needs to be by serial or inside the rom itself call the update mode.
maybe DDR clock is different.
u-boot serial console log says
h96max x2 with stock firmware
LPDDR3 probe
ddr clk to 792MHz
when I try with a95x f3 fw (don't work anymore)
LPDDR3 probe
ddr clk to 912MHz
when I try with GT1 mini-2 fw (flash failed at half porcess)
LPDDR3 probe
ddr clk to 600MHz
-------------
to SC,
If possible, please reduce the system partition size as small as possible in next build.
to SC, if popssible, compress the update image as 7z or zip before cloud upload , that make download size half.
and thnaks.
------------------------------
if you have a box with LPDDR3, most custom roms (for DDR4) are not compatible maybe.
I have , h96max x2 (4G lpddr3) a95x f3 air (maybe lpddr3) , and all custom roms are failed to boot.
Ye i know... i compress them in the past then ppl complained, and i stop compressing them.. anyway i will think about it again.
Well i have a x96max s905x2 with 4GB lpddr3 and is booting just fine, you only lose the front display and to flash the box again it needs to be by serial or inside the rom itself call the update mode.
I try to update system image only of this firmware.
My boxs run well, better than stock firmware.
But my boxs have smaller system partition size , 0x5c800000 and 0x60000000 than this image's system size 0x78000000.
So require to resize the partitions or to shrink the image before update.
If possible, please reduce the system partition size as small as possible.
if you want to try...
[0] check your system partition size : " dmesg | grep meson-mmc " in adb shell.
your box is android 9.0 already. (android 8.1 has different part structure , not compatible)
[2] Using the CustomizationTool.exe, unpack the image and get system.PARTITION.
if your system part size is smaller than 0x78000000, you have to shrink the image before update.
In linux , simg2img -> resize2fs -> img2simg , get the image that fits your system size.
[3] Using AMLogicTools_V6.0.0\bin\update.exe , update the system partiton only
install the driver (AMLogicTools_V6.0.0\driver) if you don't install the amlogic usb_burning_tool before.
plug usb a-a cable
adb shell "reboot update" <--- will make the device usb burning mode, or try reset button with toothpick.
update scan <-- check device is ready
update bulkcmd "disk_initial 0"
update partition system system.PARTITION <--- update
update bulkcmd "reboot recovery" <-- go recovery mode
Yes it should work just fine in that box... but you will lose reset button!
So if you want to flash back to another rom you need to do it from inside rom in a shell or in serial console...
Hello? You mean this firmware can work on X96 Air?
No creo que trabaje en x96 Air,pq es similar a hk1 box,yo he metido en mi hk1 box el firm disponible ATV de la caja x96 Air,son dos cajas similares,este firm me daba error.lo decía por si alguien con un box similar quiere firm ATV,que busque el del x96air
well i did some more changes to the device tree and uboot, to make it a bit more stable in DDR4 and LPDDR4 devices.
I will rls a ota zip as soon as a i can! or i might just update the images in 1º post with the newer uboot/dt... still thinking...
alright thats what I wanted to ask...pretty nice I dont bhave to care abot DDR, LPDDR blabla... :-P
Would be nice if someone can confirm this runs on HK1 PLAY (S905x2, LPDDR4)
Por si le sirve a alguien,los que tengan box incompatible,yo al final he metido la ATV del x96 Air en un hk1 de 128gb y me ha funcionado,no se se es problema con DDR3 o ddr4 pero la del x96 Air ATV me ha funcionado en otro tvbox,en concreto el hk1 box de 128 GB.gracias x tu trabajo igualmente.
Hello? You mean this firmware can work on X96 Air?
Por si le sirve a alguien,los que tengan box incompatible,yo al final he metido la ATV del x96 Air en un hk1 de 128gb y me ha funcionado,no se se es problema con DDR3 o ddr4 pero la del x96 Air ATV me ha funcionado en otro tvbox,en concreto el hk1 box de 128 GB.gracias x tu trabajo igualmente.
Like i said in 1º post, based on AML reference design... i do not know how many are based on them, that i why i also wrote "use at your own risk".
But i can tell you this, it works on mini1/2, s95, x96 max, tx5 max and my work boxes.
OK, thank you for the useful information.
Out of curiosity, I thought I would try this firmware carefully...
Leave a comment: