If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Thanks ReaperMan for the assistance. Bang head on wall X 1000 for me.
I have a photo of the board below and was hoping to either get away with not shorting the board or shorting it from the top of the board if it was possible .
I can see power on the device when I plug it in, the led is on, but no image or logo appears on the TV.
I think it may be an Evanpo device.
I've heard that it's possible to still use the sdcard method when the device is in this mode as long as the stock firmware is placed on the card. Is this true?
Thanks ReaperMan for the assistance. Bang head on wall X 1000 for me.
I have a photo of the board below and was hoping to either get away with not shorting the board or shorting it from the top of the board if it was possible .
I can see power on the device when I plug it in, the led is on, but no image or logo appears on the TV.
I think it may be an Evanpo device.
I've heard that it's possible to still use the sdcard method when the device is in this mode as long as the stock firmware is placed on the card. Is this true?
Have you tried the China Box on a different T.V.? Some firmware < > TV's do not work or must start at default 720p, getting a black screen.. (I had a box that you had to unplug the HDMI(RISKY) and the T.V would then "HDMI Handshake")
If it is bricked.....
If you have LED on, then it should only be "soft-bricked"?
Give USB Burn Tool a chance. Does it recognize your China Box?
If it "beeps" then it is a matter of choosing a better software...make sure to select <Erase Bootloader> if going from different versions of Android.
SD card method is more risky in my opinion. I've gotten 100% burn success and resulted in a "Hard-Brick".
Hello there and thank god I found this forum.
I have the (almost) same problem as Sgwells.
I bought this box without knowing there are a lot of clones around. I guess it's not a sunvell, but I'm too much of a noob to know how to find out.
I flashed TWRP via adb on my box and tried to flash a better ROM (atvxperience) and something went wrong. Now when I power the box the led lights up and the screen shows the yellow "T95Z", and that's it.
I first tried the "boot from sd card" method with the uboot, the ini file and the img on the card.
Then I tried about a million different ways using the burning tool. Different ROMs, different ways with/without toothpick in while starting, different things ticked in the burning tool (erase boot etc), because I couldn't find any clear tutorial.
It got 2 different errors, unfortunately forgot which one hapened when.
One is: Ramcode/Initialize DDR/Read initialize status/Error result
The other one (I think it's the more common at 7%): uboot/Get result/DiskInitial error.
I'm sorry for being so stupid bying before thinking and doing research, and flashing with just half knowing what I do, and now crying for help.
But after all my experience with flashing phones and having nice helpful people around, I'm optimistic to get some good advise here.
Thanks ReaperMan for the assistance. Bang head on wall X 1000 for me.
I have a photo of the board below and was hoping to either get away with not shorting the board or shorting it from the top of the board if it was possible .
I can see power on the device when I plug it in, the led is on, but no image or logo appears on the TV.
I think it may be an Evanpo device.
I've heard that it's possible to still use the sdcard method when the device is in this mode as long as the stock firmware is placed on the card. Is this true?
I have the same device only that it is 2018 version. But the chipset etc seems to be identical.
Is it a clone of the Sunveill T95Z? If yes, can someone point me in the right direction to be able to use USB Tool to load & upgrade firmware? Trying to use Poison for Sunveill the firmware gets damaged and it does not boot anymore.
USB TOOl can communicate with the device but it fails on differente areas, mostly after erasing the bootloader and starting the DDR part. I have tried using external power, using another computer, etc. The process starts always but also fails always. Don't know what to do
I even tried using the Card Burner and inserting a micro sd card, but that was even worse.
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment