If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Here is my mod for H96pro+.
Cut a square hole on top of the CPU and glue a 4cm x 4cm fan using hot glue gun.
The fan is power direct from pcb (solder from power connector), thus is running with 5VDC instead of 12VDC.
To make it look nicer, I have turn the box upside down and added 4 tiny legs to allow air flow.
The fan is put to blow air from bottom and hot air exit from top.
Temperature is not super but sufficient, idle around 52DegC and max around 62-64DegC.
Mainly due under voltage to the fan, dun like to have many cable connected to the box and most important is virtually noise coming out from the box even I m just 0.5 meter infront of it.
Cheers. Happy Mod.
You may only view thumbnails in this gallery.
This gallery has 4 photos.
I wonder what temp r u getting without any fan...just the top opened...
On android 6.0 , just with few 5-6 mm holes on top, was around 65-68 degC.
When upgraded to SC 7.1 , I m getting around 72-78 degC on max.
Worry of throttling performance, I bite the bullet to put a fan there.
On android 6.0 , just with few 5-6 mm holes on top, was around 65-68 degC.
When upgraded to SC 7.1 , I m getting around 72-78 degC on max.
Worry of throttling performance, I bite the bullet to put a fan there.
Can a 30mm fan fit inside ?
anyone knows why on android 7 the temps are higher?maybe on android 6 the sensor is not correct
First try was a simple cooling fan sucking air through the bottom case vents, it pulled air in the side vents...no case mods. temp was 45C watching live HD TV, never saw it go above 53C.
You may only view thumbnails in this gallery.
This gallery has 3 photos.
3Photos
HK1 Pro Plus
FlowFon F1
H96 Pro+ (Wisdom-Green Board-2017-02-10 H96-S912-TVBOX(DDR4)-V0.2)
MXQ Pro+
R-TVBOX Mini+
MK809III
Next modded case by prying off the logo strip. Removed the original heat sink and replaced it with two 30MMX30MMX10MM heatsinks stuck together. Leaned a USB fan against it, at idle got CPU temps of 30C and watching HD video got 35C.
With no fan, 44C at idle and 48C on HD video.
I closed in the top using the original logo strip and with the fan leaning against the heatsink measured 34C at idle and 37C on HD video. I ordered a smaller fan to stand up behind the heatsink.
A watt meter shows the box drawing 2-4 watts while playing HD video.
You may only view thumbnails in this gallery.
This gallery has 6 photos.
6Photos
HK1 Pro Plus
FlowFon F1
H96 Pro+ (Wisdom-Green Board-2017-02-10 H96-S912-TVBOX(DDR4)-V0.2)
MXQ Pro+
R-TVBOX Mini+
MK809III
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment