[ROM] AlfaWise H96 PRO+ 3/16Gb - 3/32Gb - 3/64Gb - SCV7A 7.1.2 (DDR3/DDR4 and 9377 Wifi Chipset)

[hcardoso483]

Thanks for the advice. SD card method seems non responsive box just stays on the Power blue led and doesn't even flash if reset is pushed. The red audio out led however is on.

I've tried Superceleron's blue version as the board is definitely a 3+32/ 9377 CZ-S32-V5. It also shows S32-V5 LPDDR3. Manufacture date 29-08-2017. I believe the original firmware was dated 10-10-17 which I have also downloaded the LP version from links on Freaktab however this also failed again at 8%.
Again the error message in USB burning tool was: HUB3-1 2018-06-21 18:32:38 169 [0X30403003] UBOOT/Partition_aml_dtb/Download buffer/Data transfer error

USB burning tool appears to partition and format then fails on the upload of the file to device memory. This I think is causing the download buffer data transfer error.

I had once a problem with my box not flashing firmware that was becouse somehiw I had a bad download file, sdcard method always works good for me, also check the versions of the USB burning tool sometimes on some devices it is relevant what version you use unfortunately in your case I don't know the USB version required but make sure you got a good download and the version of the USB tool is the right one also you can use this burn card maker tool

https://mega.nz/#!LJIB2KLI!7UC1bgiB_...YMHWcog5w596LY

Insert a fat 32 formated sdcard and use the normal erase option

For the USB burning tool the one I use is this

https://mega.nz/#!6N4RDLjb!c2XRwu8gL...-chLJZ17muv4S4

Some times you get error flashing becouse you need a Mac key use this one

https://mega.nz/#!XBJ0kaJK!IxjKFnCiZ...UtT1zDsBRM6ACA

I hope this helps you but don't give up your box is not dead it has the wrong firmware in it

If you need additional power to the box the way to do is
1-press and hold reset button
2- plug USB cord still holding the reset button
3- plug the power cord hold still the reset button untill you see that the device restarted ( during the detection on the ram the device will restart a write bootloader then will soft reboot again and write firmware if you pay attention you can see it happening

[lyubodelev]

And keep the reset button pressed! Release it, after the process comes to 8%.

[lyubodelev]

How long is your cable? Shorten it - 50cm.

[Modelman]

Thanks for the advice. SD card method seems non responsive box just stays on the Power blue led and doesn't even flash if reset is pushed. The red audio out led however is on.

I've tried Superceleron's blue version as the board is definitely a 3+32/ 9377 CZ-S32-V5. It also shows S32-V5 LPDDR3. Manufacture date 29-08-2017. I believe the original firmware was dated 10-10-17 which I have also downloaded the LP version from links on Freaktab however this also failed again at 8%.
Again the error message in USB burning tool was: HUB3-1 2018-06-21 18:32:38 169 [0X30403003] UBOOT/Partition_aml_dtb/Download buffer/Data transfer error

USB burning tool appears to partition and format then fails on the upload of the file to device memory. This I think is causing the download buffer data transfer error.

[hcardoso483]

Thanks for the response. I have already tried and it didn't make any difference. Also the reset button seems to be unresponsive. This box may be dead !

No it is not dead it has the wrong bootloader in it so it's trying to find the right firmware on the sdcard tray, the only way to recover from that is with the sdburning card method, find the correct firmware for your box, use the sdcard burn method, make the card and insert it to the tray, give power to the box, if you do everything right you don't even.need to press reset the box will start flashing becouse it is already looking for firmware in that tray, it's a security thing on this Chinese devices that I only learned after trowing 2 of them to the thrash bin (stupid me hehehe) mNiwbi know, this duvices are hard to kill, unless is something with the electronics there always a way to bring them to life, on the s912 chipset you can short pins too for last resorce (I don't recommend shorting pins unless you try everything else and you know for sure that you are flashing the correct firmware) Good luck...