[ROM] AlfaWise H96 PRO+ 3/16Gb - 3/32Gb - 3/64Gb - SCV7A 7.1.2 (DDR3/DDR4 and 9377 Wifi Chipset)

[X92-2GB]

Hi!



Ok, thanks, tried to back to stock firmware, but at the end the box didn't boot and now is dead turn on blue light but nothing happens. Repeat the procedure to update but no luck

Any ideas? To recover the box?

So you flashed by erasing bootloader? If your box doesn't boot you probably will need to try using a SD card flash or mask rom pin short method. Next time do not flash with erase boot loader on a firmware that is not made for your box. I assumed you knew if your box was lpddr3 or ddr3, v5 and v6 boards are lpddr3, v6.1 boards use stock rom only.

[zugsat]

Hi!

Here Is the link to the thread... It is on the first part of the page, as a link.

https://forum.freaktab.com/forum/tv-...p-mac-20180706

You may need to adjust the build.prop to have a dpi set from 240 to 340, and enable developer mode to set width to 720 for the picture to properly display for TV.

If dpi in build.prop is factory set below 340, you will need to update your play services and play store. I use apkmirror.com.

select either nodpi or 340 dpi variants. Once updated, all further updates will stick with the update you installed, so no issues with reversion, unless you manually uninstall the updates in app manager.

be sure to select 64 bit or ARM8a variants if available for all Google apps you may install. Example Chrome and play services may have Arm7 only at the time you search. If you wait a few days you may see ARM8a available, same with dpi, though play store will mostly be nodpi and it is just fine.

reason why I gave info about this, is the latest build has its quirks. I found most of them are because of Google services or apps.

If you flash twrp, you can replace gapps with a nano package fairly easy as a two step process once you down load the gapps flashable zip file. I don't have a link, but you can search online for nano gapps, and once on the download page, you can select system and config options to download the file.

Ok, thanks, tried to back to stock firmware, but at the end the box didn't boot and now is dead turn on blue light but nothing happens. Repeat the procedure to update but no luck

Any ideas? To recover the box?

[X92-2GB]

Hi!



Thanks.

Tried the eyetv firmware, but the problem is the same, where I can find the lpddr3 stock firmware?

With the original firmware the game pad was working good, but because my kid likes asphalt 8, and that game starts completely off the screen and is impossible to play, I think that maybe solved by this firmware, but I was completely wrong asphalt continues with the same problem and lost game pad Bluetooth connection.

Here Is the link to the thread... It is on the first part of the page, as a link.

https://forum.freaktab.com/forum/tv-...p-mac-20180706

You may need to adjust the build.prop to have a dpi set from 240 to 340, and enable developer mode to set width to 720 for the picture to properly display for TV.

If dpi in build.prop is factory set below 340, you will need to update your play services and play store. I use apkmirror.com.

select either nodpi or 340 dpi variants. Once updated, all further updates will stick with the update you installed, so no issues with reversion, unless you manually uninstall the updates in app manager.

be sure to select 64 bit or ARM8a variants if available for all Google apps you may install. Example Chrome and play services may have Arm7 only at the time you search. If you wait a few days you may see ARM8a available, same with dpi, though play store will mostly be nodpi and it is just fine.

reason why I gave info about this, is the latest build has its quirks. I found most of them are because of Google services or apps.

If you flash twrp, you can replace gapps with a nano package fairly easy as a two step process once you down load the gapps flashable zip file. I don't have a link, but you can search online for nano gapps, and once on the download page, you can select system and config options to download the file.

[zugsat]

Hi!

Flash the latest lpddr3 stock firmware and test your game pad. If it don't connect, then it must be a game pad driver issue with both firmwares.

another option is to flash eyetv firmware and test game pad. It may be your only option, until someone produces a game pad blue tooth driver set to ota update to our s912 boxes

Thanks.

Tried the eyetv firmware, but the problem is the same, where I can find the lpddr3 stock firmware?

With the original firmware the game pad was working good, but because my kid likes asphalt 8, and that game starts completely off the screen and is impossible to play, I think that maybe solved by this firmware, but I was completely wrong asphalt continues with the same problem and lost game pad Bluetooth connection.

[X92-2GB]

Hello!

After some work, finally I managed to do the update.

But I have problems with Bluetooth, can?t connect my Ipega 9069 gamepad, made a search but don't find any answers.

Any idea what could be the problem?

Blue pcb, wifi working fine.

Flash the latest lpddr3 stock firmware and test your game pad. If it don't connect, then it must be a game pad driver issue with both firmwares.

another option is to flash eyetv firmware and test game pad. It may be your only option, until someone produces a game pad blue tooth driver set to ota update to our s912 boxes

[zugsat]

Hello!

After some work, finally I managed to do the update.

But I have problems with Bluetooth, can?t connect my Ipega 9069 gamepad, made a search but don't find any answers.

Any idea what could be the problem?

Blue pcb, wifi working fine.

[Cipronido]

Hi, in first place, thank you by your rom, is awsome.
However, I have a doubt. I am using your ROM for a car system, it works very well, but I have a problem with the usb gps. I am using the GNSS commander to get the gps signal, using the simulated option, and every time I restart, the program asks me for permission to connect the gps usb, even if I check the box to allow the use of the gps. In the rom stock, this did not happen, I wonder if it has changed any permit or something that can be fixed.
Once again, thanks for your ROM

[ReaperMan]

Try SCV1 (Android 6) or Firmware 20180409...or newer depending whether your China Box has LP or non-LP memory.

[Luca]

I have install this firmware few days ago. I have replace the Youttube apps by the one from Google store. It work fine for a few day but today, the app dont work anymore. I have sound but no video, just a black screen. I have tried to reinsall the apps and also try Youtube for androidTV but both apps have the same problem. Is it on me that have experience this issue?

^^^^^^^
Youtube apps magically works again. Maybe it was a problem with their site...

Hi, the same thing happens to me too, okay some day, then black screen OK audio, the only solution to restart box

[mesutpeker]

I looking for compatible rom

[mesutpeker]

Hi. I have a H96 Pro Plus. I cant install because "low power" error at %25. Help me please. My Device black board. CZ-S32-V6.1

[X92-2GB]

Hello thanks for you answer can you post here this technic and where is the link ? to take that i have SC4A and i would like windevine L1

Like I said, L1 ain't gonna happen if your box never had it.

[dangchui]

Hello thanks for you answer can you post here this technic and where is the link ? to take that i have SC4A and i would like windevine L1

[X92-2GB]

Hello Superceleron there s now 5 MONTH in FRANCE For My CANAL Apk it s necessary to have WINDEVINE L1 And with this ROM there s WINDEVINE L3

your ROM is on ROM NEXUS IS it possible to repacK firmware with an other model

one people says there s technic with MAGISK and module magisk HIDE

Magiskhide props config to change the H96 fingerprint to that of a certified device for example FIRESTICK TV

or OTHER and magiskhide props config modules downloaded from within magisk manager,

Why so many modules? So far very few magisk modules work well enough to use them.

I installed a live version of a bundled zip of Sony Music (which updates via play store), and a rock solid stable version of V4A, that don't mess with DTS output with HBO Go and others that pass DTS.

I just use a finger print to download hidden apps for Sony and Samsung on play store, and leave it be, as L1 wide vine is not and will not be a patch to install. Read up, none of our boxes have L1, and it is a factory install in a hidden partition, that cannot be setup on boxes that never had it.

[dangchui]

Hello Superceleron there s now 5 MONTH in FRANCE For My CANAL Apk it s necessary to have WINDEVINE L1 And with this ROM there s WINDEVINE L3

your ROM is on ROM NEXUS IS it possible to repacK firmware with an other model

one people says there s technic with MAGISK and module magisk HIDE

Magiskhide props config to change the H96 fingerprint to that of a certified device for example FIRESTICK TV

or OTHER and magiskhide props config modules downloaded from within magisk manager,