Help me please erro [0x30405004] USB burning tool

[bumerc]

first try the 792mhz version, if it does not work, then 672mhz version. Boot log is desired.

u-boot@792mhz
u-boot@672mhz

[Nebojsa]

Here is 792mhz bootlog:

GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY:0 ;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 139759

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR4 chl: Rank0+1 @ 792MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x00066200
▒▒GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY :0;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 139738

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR4 chl: Rank0+1 @ 792MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x00066200
epGXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY :0;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 139746

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR4 chl: Rank0+1 @ 792MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x00066200
^▒▒GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RC Y:0;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 139757

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05


And 672mhz:

GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY:0 ;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 140643

BL2 Built : 20:32:17, Sep 8 2017.
gxl g6296b83 - xiaobo.gu@droid12

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
STICKY_REG0: 0x00000000
STICKY_REG1: 0x00000000
STICKY_REG9: 0x00000000
DDR3 chl: Rank0+1 @ 672MHz - FAIL
STICKY_REG0: 0x00000000
STICKY_REG1: 0x00000000
STICKY_REG9: 0x00000000
DDR4 chl: Rank0+1 @ 672MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x0002c600
Load bl33 from SD, src: 0x00050200, des: 0x01000000, size: 0x00066600
ፕ▒▒GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RC Y:0;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 140683

BL2 Built : 20:32:17, Sep 8 2017.
gxl g6296b83 - xiaobo.gu@droid12

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
STICKY_REG0: 0x00000000
STICKY_REG1: 0x00000000
STICKY_REG9: 0x00000000
DDR3 chl: Rank0+1 @ 672MHz - FAIL
STICKY_REG0: 0x00000000
STICKY_REG1: 0x00000000
STICKY_REG9: 0x00000000
DDR4 chl: Rank0+1 @ 672MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x0002c600
Load bl33 from SD, src: 0x00050200, des: 0x01000000, size: 0x00066600
▒GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY: 0;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 140679

BL2 Built : 20:32:17, Sep 8 2017.
gxl g6296b83 - xiaobo.gu@droid12

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
STICKY_REG0: 0x00000000
STICKY_REG1: 0x00000000
STICKY_REG9: 0x00000000
DDR3 chl: Rank0+1 @ 672MHz - FAIL
STICKY_REG0: 0x00000000
STICKY_REG1: 0x00000000
STICKY_REG9: 0x00000000
DDR4 chl: Rank0+1 @ 672MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x0002c600
Load bl33 from SD, src: 0x00050200, des: 0x01000000, size: 0x00066600

[bumerc]

RAM memory has now been properly initialized. BL33 (u-boot) does not start though. There was apparently an error writing. Please first delete all data from the SD card -> use SD Formatter. Then repeat the writing process from the bootloader @792Mhz.

[Nebojsa]

So, I use SD formatter and format sd card (FAT32).
Then use BootcardMaker with u-boot.bin.sd.bin @792Mhz and make the card.
It says "success", then I put sdcard to slot in the box.
Connect box to pc and power, Putty give me bootlog.
I write this to see if I miss something.

GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY:0 ;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 139824

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR4 chl: Rank0+1 @ 792MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x00066200
▒GXM:BL1:dc8b51:76f1a5;FEAT:ADFC318C:80;POC:3;RCY: 0;EMMC:0;READ:800;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 139774

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vdd cpu_a to 1120 mv
set vdd cpu_b to 1050 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR4 chl: Rank0+1 @ 792MHz - PASS
Rank0: 2048MB(auto)-2T-18
Rank1: 1024MB(auto)-2T-18
DataBus test pass!
AddrBus test pass!
Load fip header from SD, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from SD, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from SD, src: 0x00020200, des: 0x05100000, size: 0x00018400
Load bl33 from SD, src: 0x0003c200, des: 0x01000000, size: 0x00066200

[bumerc]

BL33 does not start. Do you have a Linux PC at home? I prefer Linux Terminal ..
Or another box with preinstalled Linux or Android (rooted)?

[Nebojsa]

Do not have LInux, sorry.
I have R-Box Pro box and it's rooted. What we can do with it?
I have Nvidia Shield K1 tablet, also.

[bumerc]

We can write u-boot to the MicroSD card via Android Terminal. I'll write a short tutorial right away.

[bumerc]

1. Format MicroSD Card in FAT32 and put it in the Android box.
2. Copy u-boot.bin.sd.bin to the folder /sdcard of your Android Box.
3. Open Android Terminal App and run the following commands:

su

dd if=/dev/block/zero of=/dev/block/mmcblk1 bs=1 count=442

dd if=/dev/block/zero of=/dev/block/mmcblk1 bs=512 skip=1 seek=1 count=2047

dd if=/sdcard/u-boot.bin.sd.bin of=/dev/block/mmcblk1 bs=1 count=442

dd if=/sdcard/u-boot.bin.sd.bin of=/dev/block bs=512 skip=1 seek=1

sync

[Nebojsa]

Can I do this with my rooted HTC One M8?
Ok, will try when I get home. Thanks.

[Nebojsa]

dd: /dev/block/zero: no such file or directory

Here is what I have in /dev/block directory

https://s20.postimg.cc/qfgzqigmh/IMAG3044.jpg

This is a directory of my working R-Box pro box where I started Terminal emulator for Android.

[bumerc]

sorry I fell asleep. Before we move on, try to write u-boot.bin instead of u-boot.bin.sd.bin on the SD card. I do not have windows and can not control how BootcardMaker works

[Nebojsa]

Yes, so do I
I tried with u-boot.bin but no luck.

LOOP:2;EMMC:0;READ:800;SD:0;READ:0;CHK:AA;USB:8;LO OP:3;EMMC:0;READ:800;SD:0;READ:0;CHK:AA;USB:8;LOOP :4;EMMC:0;READ:800;SD:0;READ:0;CHK:AA;USB:8;LOOP:5 ;EMMC:0;READ:800;SD:0;READ:0;CHK:AA;USB:8;

[bumerc]

Ok., then we were right with the procedure. Incidentally, "dd" is also available for Windows.
You can also run Linux on Windows via VMware.
Please inform yourself about these possibilities and I will check the BL33 in time.

[bumerc]

Nebojsa

I'll provide you with another u-boot version (u-boot.img) to download today. You can easily write this version to the MicroSD card via the Win32DiskImager.

[Nebojsa]

I got Win32DiskImager and waiting Thanks!