[ROM] Beelink GT1 / Alfawise S92 TVStock Nexus ROM (Android TV 7.1)

[sweetnonso]

Okay., because my OneDrive cap got lowered to 30GB when my annual O365 subscription expired a few days ago, I'm going to do a pre-release through the FreakTab archive site for now. This will be updated with faster links when I'm bumped back up sometime in the next 48 hours.

Important Note: The underlying OEM firmware seems to be only compatible with the Beelink GT1 Ultimate LPN1 hardware. There's considerable risk to flashing this on older hardware revisions. (I had to do a Mask ROM Mode recovery on my Alfawise S92.)

Changelog (20190223):

• Based on latest OEM firmware release for the GT1 Ultimate LPN1 (GT1_710N1)
• Live Wallpaper service (and factory live wallpapers) are restored to Nano and Stock builds
• Updated to TWRP Recovery 3.2.3-0 using minimal OMNI twrp-8.1 branch and latest OEM kernel
• Latest build from Open GApps (20190224)

Download:

• Nano Variant: BURN PACKAGE (1.22GB IMG file), OTA UPDATE (620MB ZIP file)
• Stock Variant: BURN PACKAGE (1.52GB IMG file), OTA UPDATE (814MB ZIP file)
• TVStock Variant: BURN PACKAGE (1.29GB IMG file), OTA UPDATE (678MB ZIP file)

Any chance of doing an update release for Alfawise S92 please?

I don't know that there'd be much value added. It would just be updating to the latest OpenGApps build, right?

[Guest]

Guest Long waited Android TV rom for LPN1 . Many Thanks!

[beo59]

Hi Folks,
i have a GT1 with serial A912, current ROM is the stock from Beelink 708N0_AP6255.
When i try to burn one of the images from here (tried with usb burning tool 2.0.8 and 2.1.2) i am getting an error right at the beginning of the process after "Download DDR".
Burning the stock from Beelink goes just fine.
What could be the possible reason for this?

[11:41:11 272][HUB5-1][Inf]-------------Download DDR.USB-----------
[11:41:11 272][HUB5-1][Inf]--2-2-0-0
[11:41:11 272][HUB5-1][Inf]--Control write pll reg1 0xd9000000:0x000000b1
[11:41:11 773][HUB5-1][Inf]--Control write pll reg1 0xd9000000:0x00005183
[11:41:12 274][HUB5-1][Inf]--Write initial succeed
[11:41:12 274][HUB5-1][Inf]--Upload encrypt at 0xc8100228
[11:41:12 274][HUB5-1][Inf]--ulValue = 0xadfc318c
[11:41:12 274][HUB5-1][Inf]--Read encrypt value succeed
[11:41:12 281][HUB5-1][Inf]--Transfer complete
[11:41:12 281][HUB5-1][Inf]--Run at address 0xd9000000
[11:41:12 282][HUB5-1][Inf]--RunInRam succeed
[11:41:12 658][HUB5-1][Inf]--IOCTL_IDENTIFY_HOST_Handler ret=-5 error_msg=libusb0-dll:err [control_msg] sending control message failed, win error: A device attached to the system is not functioning.


[11:41:12 658][HUB5-1][Err]--CheckFileRunState failed
[11:41:12 658][HUB5-1][Inf]--Failure : 1, FailureMax : 3
[11:41:12 660][Global][Inf]--Catch DBT_DEVICEREMOVECOMPLETE
[11:41:12 661][Global][Inf]--Scan usb device
[11:41:12 661][Global][Inf]--Aml scan WorldCup Device
[11:41:12 663][Global][Inf]--Host: Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E2D
[11:41:12 663][Global][Inf]--DevPath:\\?\pci#ven_8086&dev_1e2d&subsys_16e810cf&rev_04#3&11583659&0&d0#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[11:41:12 664][Global][Inf]---->Roothub:USB#ROOT_HUB20#4&2278ac73&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[11:41:12 664][Global][Inf]-------->[Port0]USB#VID_8087&PID_0024#5&a287287&0&1#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[11:41:12 664][Global][Inf]---------->[Port0]NoDeviceConnected
[11:41:12 664][Global][Inf]---------->[Port1]NoDeviceConnected
[11:41:12 665][Global][Inf]---------->[Port2]Other device
[11:41:12 665][Global][Inf]---------->[Port3]NoDeviceConnected
[11:41:12 665][Global][Inf]---------->[Port4]NoDeviceConnected
[11:41:12 665][Global][Inf]---------->[Port5]NoDeviceConnected
[11:41:12 665][Global][Inf]-------->[Port1]NoDeviceConnected
[11:41:12 665][Global][Inf]-------->[Port2]NoDeviceConnected
[11:41:12 667][Global][Inf]--Host: Intel(R) 7 Series/C216 Chipset Family USB Enhanced Host Controller - 1E26
[11:41:12 667][Global][Inf]--DevPath:\\?\pci#ven_8086&dev_1e26&subsys_16e810cf&rev_04#3&11583659&0&e8#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[11:41:12 667][Global][Inf]---->Roothub:USB#ROOT_HUB20#4&1e2e9ada&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[11:41:12 771][Global][Inf]-------->[Port0]USB#VID_8087&PID_0024#5&339a2dae&0&1#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[11:41:12 771][Global][Inf]---------->[Port0]NoDeviceConnected
[11:41:12 771][Global][Inf]---------->[Port1]NoDeviceConnected
[11:41:12 771][Global][Inf]---------->[Port2]NoDeviceConnected
[11:41:12 772][Global][Inf]---------->[Port3]Other device
[11:41:12 772][Global][Inf]---------->[Port4]NoDeviceConnected
[11:41:12 773][Global][Inf]---------->[Port5]Other device
[11:41:12 773][Global][Inf]---------->[Port6]NoDeviceConnected
[11:41:12 773][Global][Inf]---------->[Port7]NoDeviceConnected
[11:41:12 773][Global][Inf]-------->[Port1]NoDeviceConnected
[11:41:12 773][Global][Inf]-------->[Port2]NoDeviceConnected
[11:41:12 775][Global][Inf]--Host: USB xHCI Compliant Host Controller
[11:41:12 775][Global][Inf]--DevPath:\\?\pci#ven_8086&dev_1e31&subsys_16ee10cf&rev_04#3&11583659&0&a0#{3abf6f2d-71c4-462a-8a92-1e6861e6af27}
[11:41:12 775][Global][Inf]---->Roothub:USB#ROOT_HUB30#4&332fa869&0&0#{f18a0e88-c30c-11d0-8815-00a0c906bed8}
[11:41:12 775][Global][Inf]-------->[Port0]NoDeviceConnected
[11:41:12 775][Global][Inf]-------->[Port1]Other device
[11:41:12 775][Global][Inf]-------->[Port2]NoDeviceConnected
[11:41:12 776][Global][Inf]-------->[Port3]NoDeviceConnected
[11:41:12 776][Global][Inf]-------->[Port4]NoDeviceConnected
[11:41:12 776][Global][Inf]-------->[Port5]NoDeviceConnected
[11:41:12 776][Global][Inf]-------->[Port6]NoDeviceConnected
[11:41:12 776][Global][Inf]-------->[Port7]NoDeviceConnected
[11:41:12 776][Global][Inf]--Scan USB host controller complete
[11:41:12 776][Global][Inf]--Update data center with HubMap
[11:41:12 776][Global][Inf]--Update hub5 device data
[11:41:12 776][Global][Inf]--Update HUB5-1 
[11:41:12 776][HUB5-1][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-2 
[11:41:12 776][HUB5-2][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-3 
[11:41:12 776][HUB5-3][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-4 
[11:41:12 776][HUB5-4][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-5 
[11:41:12 776][HUB5-5][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-6 
[11:41:12 776][HUB5-6][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-7 
[11:41:12 776][HUB5-7][Inf]--Update device path
[11:41:12 776][Global][Inf]--Update HUB5-8 
[11:41:12 776][HUB5-8][Inf]--Update device path
[11:41:13 159][HUB5-1][Err]--[11:41:13 159][HUB5-1][Inf]--Failure : 2, FailureMax : 3
[11:41:13 660][HUB5-1][Err]--[11:41:13 660][HUB5-1][Inf]--Failure : 3, FailureMax : 3
[11:41:13 667][HUB5-1][Err]--[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
[11:41:13 667][HUB5-1][Inf]--Close device handle 0x0000072c

[mrdigit420]

Is there a way to make 5.1 dolby surround sound work ?

Audio options are unchanged from the underlying OEM firmware.

[Sonyroc]

Hello, in France in my city, the deployment of fiber has arrived. So i noticed a bad debit in wired. How can i check this slowness ? My bit rate does not exceed 180 Mo/s. Do you have any commands to send me to test the ethernet card ? Is the network card flanged by hardware or android tv ? Thanks in advance.

Beelink GT1 s/n A912 + amlogic q201:7.1.2/NHG47L/20171221

Same here. I didn't mess with Ethernet. Whatever works with the underlying OEM firmware should also work for this custom ROM.

[Sonyroc]

Hello, in France in my city, the deployment of fiber has arrived. So i noticed a bad debit in wired. How can i check this slowness ? My bit rate does not exceed 180 Mo/s. Do you have any commands to send me to test the ethernet card ? Is the network card flanged by hardware or android tv ? Thanks in advance.

Beelink GT1 s/n A912 + amlogic q201:7.1.2/NHG47L/20171221

Hello, thank you for your answer. Your rom is perfect and functional. Before answering you, I wanted to understand how the RGMII mode works (TS stream input10/100/1000M MAC+10/100 PHY). But this is beyond my level of competence. To conclude, the GT1 box is simply limited in bandwidth.

[n1gh7man]

Hello! Sorry for noob question .). How to update Chrome on this firmware?

[n1gh7man]

Is there a way to make 5.1 dolby surround sound work ?

In my case MX Player (hw) work's only with DTS (not AC3). On Kodi AC3 and DTS works perfectly!
GT1 connected to Onkyo TX-NR414.

[n1gh7man]

Hi Folks,
i have a GT1 with serial A912, current ROM is the stock from Beelink 708N0_AP6255.
When i try to burn one of the images from here (tried with usb burning tool 2.0.8 and 2.1.2) i am getting an error right at the beginning of the process after "Download DDR".
Burning the stock from Beelink goes just fine.
What could be the possible reason for this?

...
[11:41:13 667][HUB5-1][Err]--[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error

I had the same problem. I inserted USB into another PC connector and it all worked. I don't know if it matters, the cable and PC connector (with which it worked) were USB 3.0 .

PS: When the burning tool wrote [HUB4-1] there was the same error. When I changed the connector, burning tool showed [HUB1-1] and it worked.

[mercurio07100]

thanks for your work Guest

I have not tried it yet and I want to do it soon, but how can I read it is excellent, just a question that is not clear to me, the latest update (Nexus_GT1_710N1_TVStock-20190223) works with Beelink GT1 standard A912? Or is it better to try the penultimate update?

Thanks, but be sure to read the "Important Note" in red. That ROM is for the LPN1 hardware only.

[paddy67]

Hi,

Is this rom compatible with GT1 ultimate 3/32 Gb S/N AX12 ?

Is it possible to flash with SD Card (Burn_Card_Maker), USB Burning Toll does not recognized my box ?

Thanks

[jit_mr]

Thanks for your efforts and great work but I am facing issue in flashing my box.
I have GT1 Ultimate box with sr no. 710N1, purchased on sept. 2018.

I am getting stuck at either 4% or 7% while using USB burning tools, I have tried following ROM so far each one giving the same error :

• http://freaktab.org/9252bfa15b83727c

[doiscavalos]

I have tried the chromecast feature included from my PocoF1 and didn't succeed. What am I doing wrong?
Can you please some suggestions?

Without this i guess that having and android tv box is some kind of useless.

[jit_mr]

Okay., because my OneDrive cap got lowered to 30GB when my annual O365 subscription expired a few days ago, I'm going to do a pre-release through the FreakTab archive site for now. This will be updated with faster links when I'm bumped back up sometime in the next 48 hours.

Important Note: The underlying OEM firmware seems to be only compatible with the Beelink GT1 Ultimate LPN1 hardware. There's considerable risk to flashing this on older hardware revisions. (I had to do a Mask ROM Mode recovery on my Alfawise S92.)

Changelog (20190223):

• Based on latest OEM firmware release for the GT1 Ultimate LPN1 (GT1_710N1)
• Live Wallpaper service (and factory live wallpapers) are restored to Nano and Stock builds
• Updated to TWRP Recovery 3.2.3-0 using minimal OMNI twrp-8.1 branch and latest OEM kernel
• Latest build from Open GApps (20190224)

Download:

• Nano Variant: BURN PACKAGE (1.22GB IMG file), OTA UPDATE (620MB ZIP file)
• Stock Variant: BURN PACKAGE (1.52GB IMG file), OTA UPDATE (814MB ZIP file)
• TVStock Variant: BURN PACKAGE (1.29GB IMG file), OTA UPDATE (678MB ZIP file)

Hi,
Can you pls provide more details about this ROM, I have LPN1 ''10" gt1 ultimate device, i would like to try it.
Kindly let us know if someone else installed it, it will be great if the screenshot is provided.

[ipguy]

Guys, is there any way to mount an NFS or SMB share on Android TV?

I've setup a Plex Server and Plex Client on my Beelink and I'm trying to get the Plex server to index my movies on my NAS