Announcement
Collapse
No announcement yet.
Announcement
Collapse
No announcement yet.
MXQ Pro 4k Bricked!! What pins to short for NAND.
Collapse
X
-
Thanks scooter
Still the same
Starts, goes to 4% stays on saying "download Uboot" for 3 or so seconds then this error :12:08:33 085][HUB3-1][Err]--[0x10302001]Romcode/Switch status/Check connect/Enum device error
I have tried leaving nand short on while loading, taking it off when load starts, holding reset button on while loading , letting it go when it starts.
Also can u confirm that the pins i am shorting are correct. My chip has three large circles and one small one on the top. I assume i start counting pins from the small circle corner
This BOX is not going to BEAT me!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
LOL
Thanks for your insight....You give me a shimmer of light at end of tunnel
D
Comment
-
Many devices now mk902ii/Shield/Mk68 /Ugoos/neox5/minix5 (yes they still work lol) mk80 no it doesnt work lol.
Comment
-
Hello All!
People, can somebody help me. I have similar problem
My box is t95n s905x. In console i see this:
BL2 Built : 13:48:56, Sep 23 2016.
gxl g7459bd4 - jianxin.pan@droid06
set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 1
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 528MHz - PASS
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EM MC:0;READ:0;CHK:AA;SD:0;READ:0;0.0;CHK:0;
no sdio debug board detected
TE: 228553
I see this message, when i trying to do something from micro sd port. Works only micro usb port, usb ports box don't see. When I trying to start box without microsd, in console I always see this:
GXL:BL1:9ac50e:a1974b;FEAT:ADFC318C;POC:3;RCY:0;EM MC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:1;EMMC:0;READ :0;CHK:AA;SD:800;USB:8;LOOP:2;EMMC:0;READ:0;CHK:AA ;SD:800;USB:8;LOOP:3;EMMC:0;READ:0;CHK:AA;SD:800;U SB:8;LOOP:4;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP :5;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:6;EMMC:0 ;READ:0;CHK:AA;SD:800;USB:8;LOOP:7;EMMC:0;READ:0;C HK:AA;SD:800;USB:8;LOOP:8;EMMC:0;READ:0;CHK:AA;SD: 800;USB:8;LOOP:9;EMMC:0;READ:0;CHK:AA;SD:800;USB:8 ;LOOP:A;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:B;E MMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:C;EMMC:0;REA D:0;CHK:AA;SD:800;USB:8;LOOP;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:E;EMMC:0;R EAD:0;CHK:AA;SD:800;USB:8;LOOP:F;EMMC:0;READ:0;CHK :AA;SD:800;USB:8;LOOP:10;EMMC:0;READ:0;CHK:AA;SD:8 00;USB:8;LOOP:11;EMMC:0;READ:0;CHK:AA;SD:800;USB:8 ;LOOP:12;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:13 ;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:14;EMMC:0; READ:0;CHK:AA;SD:800;USB:8;LOOP:15;EMMC:0;READ:0;C HK:AA;SD:800;USB:8;LOOP:16;EMMC:0;READ:0;CHK:AA;SD :800;USB:8;LOOP:17;EMMC:0;READ:0;CHK:AA;SD:800;USB :8;LOOP:18;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP: 19;EMMC:0;READ:0;CHK:AA;SD:800;USB:8;LOOP:1A;EMMC: 0;READ:0;CHK:AA;SD:800;USB:8;LOOP:1B;EMMC:0;READ:0 ;CHK:AA;SD:800;USB:8;LOOP:1C;EMMC:0;READ:0;CHK:AA; SD:800;USB:8;LOOP:1D;EMMC:0;READ:0;CHK:AA;SD:800;U SB:8;L
Comment
-
In USB Burning Tool I have error on 2%, or 4%. Shorting 29-30 pins dont help, reset key dont work, and box after connecting to pc immediately enable loader mode without need to pressing or shorting something.This happened after the trying firmware 7 Android If I understand, wrong firmware changes in my bootloader frequency of memory, and now box not start with this very high frequency
Comment
-
I know this thread is old but I faced the same problem and I have found out how to resolve it. Maybe it is still going to help someone.
Here is how you can recover MXQ_S905X V2_0 20161020. You will need to use aml usb burning tool.
1. Download rom from here
2. Short nand pins between 8 and 9
3. Connect tv box to pc and it should show up on aml usb burning tool
4. Flash firmware
Comment
What's Going On
Collapse
There are currently 10637 users online. 11 members and 10626 guests.
Most users ever online was 16,134 at 08:28 on 08-11-2023.
Comment