help mk808b clone not working *noob*

[phinc]

So basically I can't get it into flash mode via the OTG power/pin in the hole method.
What i can do ?

What happens if you try it? Does it boot up normally?
Do you have the drivers installed on your PC?
There are more methods to get into flash mode. Here is a quote from Finless Rom Readme on how to do it:

To put the mk808 into flash mode the easy way:
1) Remove any SDcard you may have installed.
2) Connected the supplied USB cable from the device OTG port to your PC.
It will power up and windows may detect the device. DO not worry about that. We need it powered up.
3) In the ROM kit run the ROM FLash Tool.exe.
4) YOu should see at the bottom it says "Found RKAndroid Mass Storage USB"
If it does not say that go into settings and make sure that
a) USB storage is turned ON
b) Under developer options, USB debugging is turned off
5) Once it says "Found RKAndroid Mass Storage Usb" in the flash tool click the "Reboot to Flash Mode" button.
6) Wait up to at least 10 seconds. The unit should reboot and the screen for the mk808B will be black (no ouptut).
7) If the unit does not reboot to a blank screen, repeats steps above
Congrats! You are now in flash mode! To get out of it at any time just unplug the USB power to the mk808B.
It will boot back up normally out of flash mode.

If reboot to flash mode does not work, then use this alternate proceedure.
In my ROM kit is another folder called alternate_reboot_to_flash_tool
This is the RKBatch tool. Run this tool and the 1 box should be pink.
If it is not pink again make sure:
a) USB storage is turned ON
b) Under developer options, USB debugging is turned off
Once you have a pink box, Click the "switch" button at the bottom and this should put it into flash mode.
Close this RKBtach tool now.

Flash mode using the reset button:
If you do not ever see the flash tool say "Found RKAndroid MASS Storage USB"
Or reboot to flash mode does not work, then use this manual proceedure.
1) Have the USB cable unplugged.
2) Near the HDMI port are 2 holes in each corner. One is the blue LED hole.
The other in the corner is a reset button under the hole.
Use a paper clip or something to push the reset button in this hole.
I actually enlarged the hole so a paper clip would fit.
You will feel the button "click" when you are on it.
3) Hold this button down and while holding it, plug the USB cable from the PC to the OTG port on the mk808B.
4) YOu should here windows BONG it found a new device. The LED will not light!
5) You are now in ROM flash mode. Read below for installing drivers.

[szov]

What happens if you try it? Does it boot up normally?
Do you have the drivers installed on your PC?
There are more methods to get into flash mode. Here is a quote from Finless Rom Readme on how to do it:

Thanks for the help, but sent it back to exchange.

Waiting for a new mk808b

Again thanks

[raslvideos]

yes all original firmware, working WiFi and BT

I've MK808B with MT5931SA and MT6622N and I'm using a firmware that wifi and bluetooth aren't working.
I already try all firmware's links from this thread, but they are off.
Can you post again a valid link to the correct firmware?
Thanks and sorry for my bad english.

[raslvideos]

I've MK808B with MT5931SA and MT6622N and I'm using a firmware that wifi and bluetooth aren't working.
I already try all firmware's links from this thread, but they are off.
Can you post again a valid link to the correct firmware?
Thanks and sorry for my bad english.

I salved this case using this rom:

https://chinagadgetsreviews.blogspot.com/2014/11/download-android-kitkat-44-stock.html