Asix AX88179 Driver RK3188

[neomode]

Okay I will try to do that.

Regard
Ray

Gesendet von meinem K6000 Pro mit Tapatalk

[sashokmc]

I compile driver as module from kernel
<4>[ 205.411007] ax88179_178a: probe of 2-1:1.0 failed with error -1
<6>[ 205.417262] usbcore: registered new interface driver ax88179_178a

<6>[ 437.910980] usb 2-1: new high speed USB device number 3 using usb20_host
<6>[ 438.125872] usb 2-1: New USB device found, idVendor=0b95, idProduct=1790
<6>[ 438.125910] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 438.125954] usb 2-1: Product: AX88179
<6>[ 438.125975] usb 2-1: Manufacturer: ASIX Elec. Corp.
<6>[ 438.125999] usb 2-1: SerialNumber: 0000000000027C
<6>[ 438.129503] DWC_OTG: dwc_otg_hcd_urb_enqueue urb->transfer_buffer address not align to 4-byte 0xde215c72
<6>[ 438.129554] DWC_OTG: dwc_otg_hcd_urb_enqueue urb->transfer_buffer address not align to 4-byte 0xde215c72
<6>[ 438.441274] DWC_OTG: dwc_otg_hcd_urb_enqueue urb->transfer_buffer address not align to 4-byte 0xdd0e2642

help me with DWC_OTG not allign issue

[neomode]

I also try the same with Rockchip sources.
same error.
Did you connect the device to otg Port?

RegardS
Ray

[sashokmc]

My log with OTG
<6>[ 2165.271009] DWC_OTG: dwc_otg_hcd_enable, disable host controller
<6>[ 2173.311080] usb 1-1: USB disconnect, device number 2
<6>[ 2185.911061] usb 1-1: new high speed USB device number 3 using usb20_otg
<6>[ 2186.126219] usb 1-1: New USB device found, idVendor=0b95, idProduct=1790
<6>[ 2186.126320] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
<6>[ 2186.126419] usb 1-1: Product: AX88179
<6>[ 2186.126472] usb 1-1: Manufacturer: ASIX Elec. Corp.
<6>[ 2186.126536] usb 1-1: SerialNumber: 0000000000027C
<6>[ 2186.131878] DWC_OTG: dwc_otg_hcd_urb_enqueue urb->transfer_buffer address not align to 4-byte 0xde215c72
<6>[ 2186.132005] DWC_OTG: dwc_otg_hcd_urb_enqueue urb->transfer_buffer address not align to 4-byte 0xde215c72
<6>[ 2186.451405] DWC_OTG: dwc_otg_hcd_urb_enqueue urb->transfer_buffer address not align to 4-byte 0xdb33dd42
<4>[ 2186.461078] ax88179_178a: probe of 1-1:1.0 failed with error -1

[sashokmc]

I found solution, but a don't know, how it fix in asix driver. http://freaktab.com/forum/developmen...-dwc_otg-error

[neomode]

Okay, I will take a look on this.

Regards
Neomode