But for the life of me cant get the thing to go into maskrom mode using the short out padds on the back as pre the guide on the geekbox forum.
In 600MHz LPDDR3 Bus Width=32 Col=11 Bank=8 Row=14 CS=2 Die Bus-Width=16 Size=2048MB mach:4 OUT Boot1 Release Time: 2015-08-13, version: 2.40 ChipType = b 2423 CPUId = 0x0 SDC_BusRequest: CMD=8 SDC_RESP_TIMEOUT 1884 SDC_BusRequest: CMD=5 SDC_RESP_TIMEOUT 1884 SDC_BusRequest: CMD=55 SDC_RESP_TIMEOUT 1884 SdmmcInit=2 0 BootCapSize=2000 UserCapSize=1d1f000 FwPartOffset=2000 , 2000 DATA_BUSY:cmd=0x8 DATA_BUSY:cmd=0x8 DATA_BUSY:cmd=0x8 SdmmcInit=0 400 StorageInit ok = 64264 LoadTrustBL Trust version:100 Open bl32.bin fail! LoadBL33 theLoader 200000 111477 INFO: Bl31 Release Time: 2015-10-29, version: 1.7 NOTICE: BL3-1: v1.1(debug):d209b14 NOTICE: BL3-1: Built : 09:26:20, Oct 29 2015 get_chip_info: chip_code is 3368! pmu_init:pd st (1ee) (1ef) INFO: BL3-1: Initializing runtime services INFO: BL3-1: Preparing for EL3 exit to normal world INFO: BL3-1: Next image address = 0x200000 INFO: BL3-1: Next image spsr = 0x3c5 U-Boot 2014.10-RK3368-10-01937-g8fe3a66-dirty (Jun 02 2016 - 21:49:35) CPU: rk3368 CPU's clock information: arm pll big = 816000000HZ arm pll little = 600000000HZ periph pll = 576000000HZ ddr pll = 1200000000HZ codec pll = 400000000HZ Board: Rockchip platform Board Uboot as second level loader DRAM: Found dram banks: 1 Adding bank:0000000000200000(000000007fe00000) 128 MiB storage init OK! Using default environment GetParam check parameter success remotectl v0.1 failed to prepare fdt from boot! power key: bank-0 pin-2 can't find dts node for ricoh619 can't find dts node for act8846 pmic:rk808 can't find dts node for pwm0 SecureBootEn = 0, SecureBootLock = 0 #Boot ver: 2015-11-12#2.40 empty serial no. checkKey vbus = 1 board_fbt_key_pressed: ir_keycode = 0x0, frt = 0 no fuel gauge found no fuel gauge found read logo on state from dts [1] can't find dts node for deviceinfo rk_hdmi_register:fail to read deviceinfo hdmi baseparamer 129437x33619980@33685516-46 tve baseparamer 129438x17371112@111-1852009585 Hdmi Devices Not Exist. can't find dts node for rk1000 parse rk1000 dts error! failed to find part:logo no fuel gauge found checkKey vbus = 1 board_fbt_key_pressed: ir_keycode = 0x0, frt = 0 Hit any key to stop autoboot: 0 load fdt from resouce. ERROR: [get_entry_ram]: Cannot find logo_kernel.bmp! Secure Boot state: 0 kernel @ 0x00280000 (0x00dc44b0) ramdisk @ 0x05bf0000 (0x0014722c) bootrk: do_bootm_linux... Loading Device Tree to 0000000005600000, end 000000000561a297 ... OK Add bank:0000000000200000, 000000007fe00000 Starting kernel ... [ 0.000000] [0: swapper: 0] Initializing cgroup subsys cpu [ 0.000000] [0: swapper: 0] Initializing cgroup subsys cpuacct [ 0.000000] [0: swapper: 0] Linux version 3.10.0 (dale@dale-All-Series) (gcc version 4.9.x-google 20140827 (prerelease) (GCC) ) #1 SMP PREEMPT Mon Aug 15 18:54:59 BST 2016 [ 0.000000] [0: swapper: 0] CPU: AArch64 Processor [410fd033] revision 3 [ 0.000000] [0: swapper: 0] Machine: rockchip,rk3368 [ 0.000000] [0: swapper: 0] rockchip_uboot_logo_setup: mem: 0x0000000002000000@0x000000007dc00000, offset:0x0000000000000000 [ 0.000000] [0: swapper: 0] hdmi init vic is 65536 [ 0.000000] [0: swapper: 0] rockchip_uboot_mem_reserve: reserve 0x0000000002000000@0x000000007dc00000 for uboot logo [ 0.000000] [0: swapper: 0] rockchip_ion_reserve [ 0.000000] [0: swapper: 0] ion heap(cma): base(0) size(0) align(0) [ 0.000000] [0: swapper: 0] ion heap(vmalloc): base(0) size(0) align(0) [ 0.000000] [0: swapper: 0] cma: CMA: reserved 16 MiB at 7cc00000 [ 0.000000] [0: swapper: 0] psci: probing for conduit method from DT. [ 0.000000] [0: swapper: 0] psci: PSCIv1.0 detected in firmware. [ 0.000000] [0: swapper: 0] psci: Using standard PSCI v0.2 function IDs [ 0.000000] [0: swapper: 0] PERCPU: Embedded 12 pages/cpu @ffffffc07fd0d000 s18688 r8192 d22272 u49152 [ 0.000000] [0: swapper: 0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 516615 [ 0.000000] [0: swapper: 0] Kernel command line: earlyprintk=uart8250-32bit,0xff690000 console=ttyS2 androidboot.baseband=N/A androidboot.selinux=permissive androidboot.hardware=rk30board androidboot.console=ttyS2 init=/init mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(trust),0x00002000@0x00006000(misc),0x00008000@0x00008000(resource),0x00008000@0x00010000(kernel),0x00010000@0x00018000(boot),0x00010000@0x00028000(recovery),0x00038000@0x00038000(backup),0x00040000@0x00070000(cache),0x00002000@0
The forum other there is spambot heven now lol
Comment