Announcement

Collapse
No announcement yet.

How Unbrick MXQ pro 4K (R329Q_V3.0)

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    How Unbrick MXQ pro 4K (R329Q_V3.0)

    i no speak english, but have hope what help-me.
    I was recently trying to update my TV box, and it ended up brick, I need help because I can't find explanations for the model I'm using. And I need to unbrick it, the model and R329Q_V 3.0
    I need help to identify the point.

    Note: No software detects the device, tried USB Burning, Android tool and RK Batch tool

    https://i.imgur.com/PiPYWQ8.jpg
    https://i.imgur.com/Fv7br9n.jpg

    #2
    Originally posted by gabx View Post
    i no speak english, but have hope what help-me.
    I was recently trying to update my TV box, and it ended up brick, I need help because I can't find explanations for the model I'm using. And I need to unbrick it, the model and R329Q_V 3.0
    I need help to identify the point.

    Note: No software detects the device, tried USB Burning, Android tool and RK Batch tool

    https://i.imgur.com/PiPYWQ8.jpg
    https://i.imgur.com/Fv7br9n.jpg
    Hi ,

    you must short Pins , on second Picture (Fv7br9n.jpg) , use Pins , i think 7/8

    to get your Box in MaskRomMode , start counting by the side with the small

    triangle , use the soldered row inside , i think , for sure you must find the two

    needed Pins there , if you need more Info ask ,

    good luck / gefatttern

    Comment


      #3
      gefattern Which triangle, can you mark in the image?

      Comment


        #4
        I used a small philipps head screwdriver to short out the pins....Seems like a flat head screwdriver or tool takes a lot more time....Better off using a philipps head screwdriver, with the flat head it doesnt do the job as effeciently....The philipps head you dont have to be precise just touch a few of the pins and hold for a few seconds and you got it....

        Comment


          #5
          Hi,

          1. Open Rochip Batch Tool (Upload Correct Firmware)
          2. Connet USB To USB Cable (device not detected yet)
          3. Push Reset Button ( inside the AV Connector)
          4. Short pin 4-5 (see picture) until device detected by Rochip batch tool
          5. Flash your device....

          Works in mine....

          Comment


            #6
            Firmware I used for Rk329Q Mxq Pro 4k - For some reason it doesnt install using the other rockchip flashing software (for me) - I had to use Factory Tool v1.6 -
            Otherwise it hangs on "android" logo screen....Tested & Workin on Rk329Q V-3.2 -Mxq Pro : Android 7.1.2


            Firmware (img File)
            http://www.mediafire.com/file/q2ev24...9_USB.img/file

            USE FACTORY TOOL INSTEAD OF OTHER SOFTWARE FOR SUCCESSFUL FLASH :
            Factory Tool v1.6
            http://www.mediafire.com/file/9irk7u..._v1.6.zip/file
            Last edited by Gradez1974; 02-25-2019, 11:57.

            Comment


              #7
              Hi, I am also trying to unbrick a MXQ 4K pro R329Q version 3.2 but no luck.
              the pc does not pick up the box it has a red and blue light that is glowing dim.
              please help

              Comment


                #8
                Originally posted by Paulod1977 View Post
                Hi, I am also trying to unbrick a MXQ 4K pro R329Q version 3.2 but no luck.
                the pc does not pick up the box it has a red and blue light that is glowing dim.
                please help
                +1

                Comment


                  #9
                  Originally posted by Paulod1977 View Post
                  Hi, I am also trying to unbrick a MXQ 4K pro R329Q version 3.2 but no luck.
                  the pc does not pick up the box it has a red and blue light that is glowing dim.
                  please help
                  FOUND THE IMG FILE I PROVIDED TOOK MORE STORAGE UP IN THE 8gb MODELS.....






                  Yeah I had similar probs.... Try unistalling the driver then reinstalling the driver that will get the pc to detect the box (hopefully).... It seems to be an issue, I had to keep reinstalling the driver after flashing the box.... That's how it was detected on my pc, also make sure u have the reset button securely pressed in when it is connected to pc.... The IMG software I ended up using eventually was located here : https://forum.freaktab.com/forum/tv-...29-sv6051-wifi



                  I have the IMG file also if necessary, can upload and sort u guys out.... let me know if anything else is needed....

                  Here it is :

                  https://www.mediafire.com/file/585jstwlygvvpuc/mxqpro-6051-nv2-1114.img/file
                  Last edited by Gradez1974; 10-26-2019, 06:58.

                  Comment


                    #10
                    Originally posted by Paulod1977 View Post
                    Hi, I am also trying to unbrick a MXQ 4K pro R329Q version 3.2 but no luck.
                    the pc does not pick up the box it has a red and blue light that is glowing dim.
                    please help

                    My bad
                    you still you may have to reinstall the drivers...
                    I used a philipps head screwdriver to short out the pins on this model....If successful the light (led) will turn off once the pins have been successfully shorted.... Hold for a few seconds than remove screwdriver (tool of choice) and pc should recognise the box.... on my pc was a constant uninstall and reinstall of drivers after a successful flash to the box..... Hopefully this helps.

                    Comment


                      #11
                      Good day, pls I've been trying to fix my r329q v3.0 for quite a while but all firmware I flash to it didn't solve problem of blue and red light. Box accepts firmware fine but blue and red light still persist, I later saw leelbox firmware and tried but still same and I discovered something funny, after flashing I connected it as usual to hdmi but no display, something tells me to still leave it connected to my PC with The USB male a cable as it just finished flashing and showing a glowing red light and at the same time I plugged power cable and also hdmi and Boom it came on screen, I removed USB male a cable and it went off, problem now is why is it powering from USB male a I constructed and when I plug adapter that came with it, it will just go back to blue and red light? Any solution will be very much appreciated.?
                      Last edited by kaino147; 11-12-2019, 01:19.

                      Comment


                        #12
                        Good morning
                        I tried to connect my R329Q v. 3.0 but on my pc with windows10 64 bit I read that the driver is unknown and there is no update; can you tell me how I should do it.
                        Thank you

                        Comment


                          #13
                          Originally posted by fabinus View Post
                          Good morning
                          I tried to connect my R329Q v. 3.0 but on my pc with windows10 64 bit I read that the driver is unknown and there is no update; can you tell me how I should do it.
                          Thank you
                          Hi ,

                          ever flashed a RKBox ??? , look here :

                          https://ugoos.net/blog/rockchip-firm...flashing-guide

                          good luck / gefattern

                          Comment

                          Working...
                          X