Unconfigured Ad Widget

Collapse

Announcement

Collapse
No announcement yet.

RK3328 Firmware Center RTL8723 , AP6255 , SV6051 , IT6334 AND MORE (Stock-ROMs , Custom-ROMs by Silver)

Collapse
This is a sticky topic.
X
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • toto8514
    replied
    Hi Silver,

    May you help me on finding the firmware of my EstgoSZ E9 RK3328 - RAM 4G ROM 64GB ?

    It is stuck in boot mode for I flashed it with a wrong firmware. Any valid firmware with any version of android is ok.

    Thanks.

    Leave a comment:


  • Silver
    replied
    Originally posted by klinyermont View Post


    Good morning, I would like to tell you that I managed to make the copy of the other mx 10 pro I did it with rkDumper_109_test because it is RKFP format and I have the copy but I can not put it in the other with rk android tools if flashing is in maskrom mode I do not know what else to do some idea

    how could I pack everything in one img to flash with factory tools
    just flash using the offsets in Android Tool. flash kernel, resource and boot

    Leave a comment:


  • klinyermont
    replied
    Originally posted by klinyermont View Post

    a copy, it does not matter that I have flashed with another firmware?
    the problem I have to make the copy is that when trying to get the parameter.txt with rk android tools 2.39 putting 0 in start and 2 in count the file it generates has nothing but nonsense letters, I have looked for another way to generate that file since they lent me an mx10 pro, the pcb and the wifi chip, but I can't find a way to make a backup. maybe you can help me

    Good morning, I would like to tell you that I managed to make the copy of the other mx 10 pro I did it with rkDumper_109_test because it is RKFP format and I have the copy but I can not put it in the other with rk android tools if flashing is in maskrom mode I do not know what else to do some idea

    how could I pack everything in one img to flash with factory tools

    Leave a comment:


  • Silver
    replied
    Originally posted by klinyermont View Post

    a copy, it does not matter that I have flashed with another firmware?
    the problem I have to make the copy is that when trying to get the parameter.txt with rk android tools 2.39 putting 0 in start and 2 in count the file it generates has nothing but nonsense letters, I have looked for another way to generate that file since they lent me an mx10 pro, the pcb and the wifi chip, but I can't find a way to make a backup. maybe you can help me
    Use "RkDumper" it may not work but try it.

    Leave a comment:


  • klinyermont
    replied
    Originally posted by mo123 View Post

    Only the seller from where you bought it can help.
    It was the first option that I exhausted but here they do not have the slightest idea on the subject, the solution they gave me was to search the internet.

    Leave a comment:


  • klinyermont
    replied
    Originally posted by Silver View Post

    ou can try to backup the boot kernel and resource iMG of stock rom and try to boot my rom with it.
    a copy, it does not matter that I have flashed with another firmware?
    the problem I have to make the copy is that when trying to get the parameter.txt with rk android tools 2.39 putting 0 in start and 2 in count the file it generates has nothing but nonsense letters, I have looked for another way to generate that file since they lent me an mx10 pro, the pcb and the wifi chip, but I can't find a way to make a backup. maybe you can help me

    Leave a comment:


  • Silver
    replied
    Originally posted by klinyermont View Post
    Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate Click image for larger version

Name:	IMG_20210201_071121-min.jpg
Views:	932
Size:	257.7 KB
ID:	819998Click image for larger version

Name:	IMG_20210201_074709-min.jpg
Views:	565
Size:	144.8 KB
ID:	819999
    ou can try to backup the boot kernel and resource iMG of stock rom and try to boot my rom with it.

    Leave a comment:


  • mo123
    replied
    Originally posted by klinyermont View Post
    Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate Click image for larger version

Name:	IMG_20210201_071121-min.jpg
Views:	932
Size:	257.7 KB
ID:	819998Click image for larger version

Name:	IMG_20210201_074709-min.jpg
Views:	565
Size:	144.8 KB
ID:	819999
    Only the seller from where you bought it can help.

    Leave a comment:


  • klinyermont
    replied

    Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate Click image for larger version

Name:	IMG_20210201_071121-min.jpg
Views:	932
Size:	257.7 KB
ID:	819998Click image for larger version

Name:	IMG_20210201_074709-min.jpg
Views:	565
Size:	144.8 KB
ID:	819999

    Leave a comment:


  • Silver
    replied
    Originally posted by levin44 View Post


    Thank you very much Silver. You are a lifesaver. I was able to get back to life my "MX9 max" tv box ( Rockchip RK3328 4core ARM Cortex A53 64-bit CPU/ 5core ARM Mali-450 GPU/ 2GB RAM/ 16GB ROM), (MINI RK3328_D4, REV:1.0, 2017 09 07)

    I used "RTL8723" (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) firmware. TV box is rooted and working perfect. WIFI also works.

    I have used "{ROM} PoisonATV RK3328" and "a9s_rk3328_d4_rtl8723_20180705_r1(mx9pro ??kodi???)" firmware before. They both installed properly, but after I unplug power, PoisonATV did not boot at all and the other ROM wiped everything and presented the initial setup every time reboot.

    Here are my steps to flash the firmware from 'Silver' (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) :
    1. Install Rockchip_DriverAssitant_v4.4 or v4.8
    2. Open "rkdev tool - AndroidTool_Release_v2.51" and goto 'Upgrade Firmware' tab
    3. Click 'Firmware' and locate the img file
    4. Remove screws of the TVbox. Refer to the image attached below and find the copper dots which are necessary to short-circuit to enter MASKROM mode.
    5. Use a wire or a conductor to connect the two dots. While doing that, connect the male-male USB cable to PC and USB 2 port of the tv box. AndroidTool will show "Found One MASKROM Device" immediately. Remove the Short-circuiting conductor.
    6. Click 'EraseFlash'
    7. Click 'Upgrade'
    8. After the upgrade is finished, remove the USB cable.
    9. Connect HDMI cable
    10. Connect power cable (sometimes, you might have to hold the av-reset pin before connecting the power cable. but I didn`t have to do that)
    11. Boot animation will appear within few seconds. If the display goes to standby mode, remove and replug the power cable.
    12. the android logo will appear. then wait.....
    13. Done !!!
    14. Let me know if this helps.
    Pins to Short-circuit:

    Click image for larger version

Name:	mx9max maskrom mode pins.png
Views:	626
Size:	191.5 KB
ID:	819923
    No problem, thats why i uploaded the ROMs so people like you have a chance of fixing the box

    Leave a comment:


  • levin44
    replied
    Originally posted by Silver View Post
    I have seen many users bricking their RK3328 TV box with incorrect firmware.
    In this thread i will supply some IMG files for you all so you can reflash your box with working wifi/bt drivers

    This includes 2 firmwares i have customized with preinstalled apps some patches and root

    ......

    Confirmed working on:

    MX9Pro
    A5XMAX
    MX10
    V88 Piano
    ...more to come

    Please test firmwares and reply back here so others know what works for what box.

    -Silver

    Thank you very much Silver. You are a lifesaver. I was able to get back to life my "MX9 max" tv box ( Rockchip RK3328 4core ARM Cortex A53 64-bit CPU/ 5core ARM Mali-450 GPU/ 2GB RAM/ 16GB ROM), (MINI RK3328_D4, REV:1.0, 2017 09 07)

    I used "RTL8723" (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) firmware. TV box is rooted and working perfect. WIFI also works.

    I have used "{ROM} PoisonATV RK3328" and "a9s_rk3328_d4_rtl8723_20180705_r1(mx9pro ??kodi???)" firmware before. They both installed properly, but after I unplug power, PoisonATV did not boot at all and the other ROM wiped everything and presented the initial setup every time reboot.

    Here are my steps to flash the firmware from 'Silver' (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) :
    1. Install Rockchip_DriverAssitant_v4.4 or v4.8
    2. Open "rkdev tool - AndroidTool_Release_v2.51" and goto 'Upgrade Firmware' tab
    3. Click 'Firmware' and locate the img file
    4. Remove screws of the TVbox. Refer to the image attached below and find the copper dots which are necessary to short-circuit to enter MASKROM mode.
    5. Use a wire or a conductor to connect the two dots. While doing that, connect the male-male USB cable to PC and USB 2 port of the tv box. AndroidTool will show "Found One MASKROM Device" immediately. Remove the Short-circuiting conductor.
    6. Click 'EraseFlash'
    7. Click 'Upgrade'
    8. After the upgrade is finished, remove the USB cable.
    9. Connect HDMI cable
    10. Connect power cable (sometimes, you might have to hold the av-reset pin before connecting the power cable. but I didn`t have to do that)
    11. Boot animation will appear within few seconds. If the display goes to standby mode, remove and replug the power cable.
    12. the android logo will appear. then wait.....
    13. Done !!!
    14. Let me know if this helps.
    Pins to Short-circuit:

    Click image for larger version

Name:	mx9max maskrom mode pins.png
Views:	626
Size:	191.5 KB
ID:	819923

    Leave a comment:


  • freddy
    replied
    Originally posted by deathphantom View Post
    Hello! I m pretty new here and to installing custom firmwares to tv boxes. I got v88 4K tv box and I thought it was too slow and wanted to try these firmwares. My question is that i got an error message while using androidtool saying "Chip check fail" when i tried to install "rk3328_d4_9.0_rtl8723bs_20181128_r1.img"

    So why do i get this error?

    Thx in advance for replies
    V-88 = Rockchip RK 3229

    Move/Navigate to there

    Roms there to test

    Good Luck

    Happy Testing

    Leave a comment:


  • deathphantom
    replied
    Hello! I m pretty new here and to installing custom firmwares to tv boxes. I got v88 4K tv box and I thought it was too slow and wanted to try these firmwares. My question is that i got an error message while using androidtool saying "Chip check fail" when i tried to install "rk3328_d4_9.0_rtl8723bs_20181128_r1.img"

    So why do i get this error?

    Thx in advance for replies

    Leave a comment:


  • Silver
    replied
    Originally posted by snyker View Post
    Hello my android box tv is a H96 Max H2 with RK3328 CPU and wifi chipset HS2734A.
    I think IT6334 chipset is the same ????
    Never had that box, try firmware at your own risk, do backup before flash!

    Leave a comment:


  • snyker
    replied
    Hello my android box tv is a H96 Max H2 with RK3328 CPU and wifi chipset HS2734A.
    I think IT6334 chipset is the same ????

    Leave a comment:

Working...
X