RK3328 Firmware Center RTL8723 , AP6255 , SV6051 , IT6334 AND MORE (Stock-ROMs , Custom-ROMs by Silver)

[Silver]

Thank you very much Silver. You are a lifesaver. I was able to get back to life my "MX9 max" tv box ( Rockchip RK3328 4core ARM Cortex A53 64-bit CPU/ 5core ARM Mali-450 GPU/ 2GB RAM/ 16GB ROM), (MINI RK3328_D4, REV:1.0, 2017 09 07)

I used "RTL8723" (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) firmware. TV box is rooted and working perfect. WIFI also works.

I have used "{ROM} PoisonATV RK3328" and "a9s_rk3328_d4_rtl8723_20180705_r1(mx9pro ??kodi???)" firmware before. They both installed properly, but after I unplug power, PoisonATV did not boot at all and the other ROM wiped everything and presented the initial setup every time reboot.

Here are my steps to flash the firmware from 'Silver' (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) :

1. Install Rockchip_DriverAssitant_v4.4 or v4.8
2. Open "rkdev tool - AndroidTool_Release_v2.51" and goto 'Upgrade Firmware' tab
3. Click 'Firmware' and locate the img file
4. Remove screws of the TVbox. Refer to the image attached below and find the copper dots which are necessary to short-circuit to enter MASKROM mode.
5. Use a wire or a conductor to connect the two dots. While doing that, connect the male-male USB cable to PC and USB 2 port of the tv box. AndroidTool will show "Found One MASKROM Device" immediately. Remove the Short-circuiting conductor.
6. Click 'EraseFlash'
7. Click 'Upgrade'
8. After the upgrade is finished, remove the USB cable.
9. Connect HDMI cable
10. Connect power cable (sometimes, you might have to hold the av-reset pin before connecting the power cable. but I didn`t have to do that)
11. Boot animation will appear within few seconds. If the display goes to standby mode, remove and replug the power cable.
12. the android logo will appear. then wait.....
13. Done !!!
14. Let me know if this helps.

Pins to Short-circuit:

No problem, thats why i uploaded the ROMs so people like you have a chance of fixing the box

[klinyermont]

Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate

[mo123]

Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate

Only the seller from where you bought it can help.

[Silver]

Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate

ou can try to backup the boot kernel and resource iMG of stock rom and try to boot my rom with it.

[klinyermont]

ou can try to backup the boot kernel and resource iMG of stock rom and try to boot my rom with it.

a copy, it does not matter that I have flashed with another firmware?
the problem I have to make the copy is that when trying to get the parameter.txt with rk android tools 2.39 putting 0 in start and 2 in count the file it generates has nothing but nonsense letters, I have looked for another way to generate that file since they lent me an mx10 pro, the pcb and the wifi chip, but I can't find a way to make a backup. maybe you can help me

[klinyermont]

Only the seller from where you bought it can help.

It was the first option that I exhausted but here they do not have the slightest idea on the subject, the solution they gave me was to search the internet.

[Silver]

a copy, it does not matter that I have flashed with another firmware?
the problem I have to make the copy is that when trying to get the parameter.txt with rk android tools 2.39 putting 0 in start and 2 in count the file it generates has nothing but nonsense letters, I have looked for another way to generate that file since they lent me an mx10 pro, the pcb and the wifi chip, but I can't find a way to make a backup. maybe you can help me

Use "RkDumper" it may not work but try it.

[klinyermont]

a copy, it does not matter that I have flashed with another firmware?
the problem I have to make the copy is that when trying to get the parameter.txt with rk android tools 2.39 putting 0 in start and 2 in count the file it generates has nothing but nonsense letters, I have looked for another way to generate that file since they lent me an mx10 pro, the pcb and the wifi chip, but I can't find a way to make a backup. maybe you can help me

Good morning, I would like to tell you that I managed to make the copy of the other mx 10 pro I did it with rkDumper_109_test because it is RKFP format and I have the copy but I can not put it in the other with rk android tools if flashing is in maskrom mode I do not know what else to do some idea

how could I pack everything in one img to flash with factory tools

[Silver]

Good morning, I would like to tell you that I managed to make the copy of the other mx 10 pro I did it with rkDumper_109_test because it is RKFP format and I have the copy but I can not put it in the other with rk android tools if flashing is in maskrom mode I do not know what else to do some idea

how could I pack everything in one img to flash with factory tools

just flash using the offsets in Android Tool. flash kernel, resource and boot

[toto8514]

Hi Silver,

May you help me on finding the firmware of my EstgoSZ E9 RK3328 - RAM 4G ROM 64GB ?

It is stuck in boot mode for I flashed it with a wrong firmware. Any valid firmware with any version of android is ok.

Thanks.

[Famous]

Hi Silver I flashed my box with rk3328_d4_7.1_rtl8723bs_20180705_r1_root but it's not booting

my box is T9 RK3328 4GB-32GB with the wifi device driver rtl8723cs

I have flash it back to the stock ROM http://www.mediafire.com/file/cy29o5...B32GB.img/file

what I want is to install Magisk, I can't install it on the stock ROM, want to try to install it on your custom ROM.

[Silver]

Hi Silver I flashed my box with rk3328_d4_7.1_rtl8723bs_20180705_r1_root but it's not booting

my box is T9 RK3328 4GB-32GB with the wifi device driver rtl8723cs

I have flash it back to the stock ROM http://www.mediafire.com/file/cy29o5...B32GB.img/file

what I want is to install Magisk, I can't install it on the stock ROM, want to try to install it on your custom ROM.

Magisk is not supported, ROM is for "rtl8723bs" you have "rtl8723cs"

Its a test rom you cannot expect it to work on every rk3328 device.

[hrrom]

with firmware rk3328_d4_7.1_ap6255_20180705_r1_root.img freeze on black screen. with rk3328_d4_9.0_rtl8723bs_20181128_r1.img start but wifi not working. Please can you build .img rk3328_d4_9.0_ap6255?

[Silver]

with firmware rk3328_d4_7.1_ap6255_20180705_r1_root.img freeze on black screen. with rk3328_d4_9.0_rtl8723bs_20181128_r1.img start but wifi not working. Please can you build .img rk3328_d4_9.0_ap6255?

No sorry, firmware is published as it is, no way to perform upgrades anymore, what box you have?

[hrrom]

this is my box. Based on MINI RK3328_D4 rev.2.0 board with ap6255 wifi.