New Rockchip Batch Tool v1.7 Plus v3.5 Drivers

[john331]

Adb Drive

I follow your instructions but on my device manager I see only Android adb interface and on theRockthip toll there is no device. Please help

[davidw]

If you are upgrading from say a manufacturers Rom to a new version of that manufacturers Rom hit the upgrade button,But if you are installing a custom firmware (Finless rom) then usually it is the restore button.

And I don't rely no what will happen to your CWM Recovery ,, but think positive nothing will go bad all will be good positive thinking..

You could always back up everything on your box then restore it on the box again when you have flashed a new rom this is a good back up apk it will back up app + data https://play.google.com/store/apps/d...pRoot&hl=en_GB

Well the restore button did the trick and the new firmware is installed. Seems pretty nice but only just looked a bit. It did wipe out my app/data. But I am not surprised. And CWM still seems to be there so I can restore a nandroid if needed.

THanks

[blinkone]

If I can impose one more time... I have this firmware unzipped and I can load the .img file into batchtool. But I am not sure if I hit the upgrade or the restore button. I think I read somewhere I can get into trouble doing the wrong thing. So what is the right thing?

Thanks.

And any idea if installing this mess with my CWM Recovery and the ability to restore a nandroid backup of my current Finless 1.3 setup in case this goes bad?

Thanks again

If you are upgrading from say a manufacturers Rom to a new version of that manufacturers Rom hit the upgrade button,But if you are installing a custom firmware (Finless rom) then usually it is the restore button.

And I don't rely no what will happen to your CWM Recovery ,, but think positive nothing will go bad all will be good positive thinking..

You could always back up everything on your box then restore it on the box again when you have flashed a new rom this is a good back up apk it will back up app + data https://play.google.com/store/apps/d...pRoot&hl=en_GB

[davidw]

Ha ha glad I could help

If I can impose one more time... I have this firmware unzipped and I can load the .img file into batchtool. But I am not sure if I hit the upgrade or the restore button. I think I read somewhere I can get into trouble doing the wrong thing. So what is the right thing?

Thanks.

And any idea if installing this mess with my CWM Recovery and the ability to restore a nandroid backup of my current Finless 1.3 setup in case this goes bad?

Thanks again

[blinkone]

Thanks very much. Doing this, my PC now recognized the new hardware as a Rockusb Device. This is real progress! I had some trouble getting a connected device to showing up in BatchTool at first. But now I seem to have it. I really appreciate the time and help.

Ha ha glad I could help

[davidw]

This video might help https://www.youtube.com/watch?v=B0ivqTAx8hA

But basicly ,Open batchtool on your pc connect OTG on minix to pc via usb lead, press recorery button on minix wile pressing recovery button power on the minix release recovery button after a 4/5 second

Thanks very much. Doing this, my PC now recognized the new hardware as a Rockusb Device. This is real progress! I had some trouble getting a connected device to showing up in BatchTool at first. But now I seem to have it. I really appreciate the time and help.

[blinkone]

Or another way if your already running finless 1.3 install this reboot apk http://www.freak-tab.de/petrus/Reboot_v1.2.2.apk on your x5 open batchtool on your pc connect your x5 to your pc via otg port power on the x5 power on the x5 then open the reboot apk then select reboot to bootloader

[blinkone]

Perhaps my understanding is too basic... Is there something I need to do with my Neo X5 to put it into a mode whereby the the batchtool can talk to it? Does it need to be in recovery mode or something else? Should I be use the OTG or a normal USB cable while using batchtool? I am pretty sure I had the ADB driver installed already since I have been developing apps for some time. Hmmm.

This video might help https://www.youtube.com/watch?v=B0ivqTAx8hA

But basicly ,Open batchtool on your pc connect OTG on minix to pc via usb lead, press recorery button on minix wile pressing recovery button power on the minix release recovery button after a 4/5 second

[davidw]

Perhaps my understanding is too basic... Is there something I need to do with my Neo X5 to put it into a mode whereby the the batchtool can talk to it? Does it need to be in recovery mode or something else? Should I be use the OTG or a normal USB cable while using batchtool? I am pretty sure I had the ADB driver installed already since I have been developing apps for some time. Hmmm.

[blinkone]

Thanks for clarifying all that. I was just guessing/grasping. I got the tool described and used it. It installed an ADB driver. I hope thats the one. After installing, I try to run the BatchTool from here and it shows no connected devices. I have tried all sorts of variations on USB->Connect To PC and USB DEbugging. In no case can I get BatchTool to show a connected device. Thanks in advance for any help.

Installing the drivers can be a hit & miss for some reason,did you reboot your pc after installing the drivers.Have you tried another usb lead,you could also try another usb port on your pc

[davidw]

Thanks for clarifying all that. I was just guessing/grasping. I got the tool described and used it. It installed an ADB driver. I hope thats the one. After installing, I try to run the BatchTool from here and it shows no connected devices. I have tried all sorts of variations on USB->Connect To PC and USB DEbugging. In no case can I get BatchTool to show a connected device. Thanks in advance for any help.

[blinkone]

I have tried several times before and thought to try again with these. My Minix X5, Rockchip 3066, with Finless 1.3 shows in Windows as a GT-I9300 device. I think this is because Finless modifies the device ID to look like a Samsung device and work better with Play Store. When I follow the instructions here to manually choose the driver, it fails. Perhaps this is because it is not acting like a Rockchip device? Any suggestions, tips, help? Thanks

The device showing up as a GT-I9300 has nothing to do with why You cant install the drivers, bob does this so the device shows up more compatible apps & games in the play store.try this tool for installing the drivers

http://blog.geekbuying.com/index.php/2013/11/08/have-problem-in-install-the-rockchip-drivers-no-worry-rockchip-release-the-drivers-auto-installation-tool-download-here/

[Kristi M]

I agree with you davidw, I also experienced the same thing with you

[davidw]

Cannot Get To Install on XP

I have tried several times before and thought to try again with these. My Minix X5, Rockchip 3066, with Finless 1.3 shows in Windows as a GT-I9300 device. I think this is because Finless modifies the device ID to look like a Samsung device and work better with Play Store. When I follow the instructions here to manually choose the driver, it fails. Perhaps this is because it is not acting like a Rockchip device? Any suggestions, tips, help? Thanks

[Android Taxi]

as again having problems try this http://www.freaktab.com/showthread.p...s-In-Windows-8