Lubuntu possible on S905?

[Koxx]

now bluetooth ...

compile broadcom tool :
git clone https://github.com/kdeenkhoorn/cubie...ster/bluetooth
cd cubietruck-scripts/sources/broadcom-bluetooth
make
sudo cp ./brcm_patchram_plus /usr/local/bin/

init bluetooth :
brcm_patchram_plus -d --patchram /lib/firmware/bcm43438a0.hcd --enable_hci --bd_addr 11:22:33:44:55:66 --no2bytes --tosleep 1000 /dev/ttyS1

in dmesg, you should see :
[ 8931.542636] ttyS1 use xtal 24000000 change 0 to 9600
[ 8931.542681] ttyS1 use xtal 24000000 change 9600 to 9600
[ 8931.542702] ttyS1 use xtal 24000000 change 9600 to 115200
[ 8939.459567] Bluetooth: HCI UART driver ver 2.2
[ 8939.459580] Bluetooth: HCI H4 protocol initialized

now attach hci :
hciattach /dev/ttyS1 any

now check :
odroid@odroid64:~$ hciconfig -a
hci0: Type: BR/EDR Bus: UART
BD Address: 11:22:33:44:55:66 ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING PSCAN ISCAN
RX bytes:691 acl:0 sco:0 events:42 errors:0
TX bytes:1075 acl:0 sco:0 commands:41 errors:0
Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF
Link mode: SLAVE ACCEPT
Name: 'odroid64'
Class: 0x000000
Service Classes: Unspecified
Device Class: Miscellaneous,
HCI Version: 4.1 (0x7) Revision: 0xf5
LMP Version: 4.1 (0x7) Subversion: 0x2122
Manufacturer: Broadcom Corporation (15)

then, start it automatically :
sudo nano /etc/systemd/system/bt-up.service

paste this :
[Unit]
Description=Bring Up Bluetooth
#After=bluetooth.target
After=network-online

[Service]
Type=idle
ExecStart=/bin/su -c '/etc/systemd/system/start-brcmbt-patchram-plus'
ExecStop=/bin/kill -HUP ${MAINPID}
StandardInput=tty
StandardOutput=tty
TTYPath=/dev/tty5
Restart=always
RestartSec=2

[Install]
WantedBy=getty.target

then :
nano /etc/systemd/system/start-brcmbt-patchram-plus

paste this :
#!/bin/sh

brcm_patchram_plus -d --patchram /lib/firmware/bcm43438a0.hcd --enable_hci --bd_addr 11:22:33:44:55:66 --no2bytes --tosleep 1000 /dev/ttyS1
hciattach /dev/ttyS1 any
hciconfig hci0 up

exit 0


paste this :
sudo systemctl enable bt-up.service

all done !
reboot to check

[Koxx]

still this crappy message which prevent me from doing modprobe :
[ 107.231421] dhd: version magic '3.14.29 SMP mod_unload aarch64' should be '3.14.29 SMP preempt mod_unload aarch64'

but it works GREAT !

EDIT : fixed. It was due to an old module still in /lib/modules. remove and depmod -a solved it.

[Koxx]

AHHHHHHHH !!!! YESSSSSSSSSSSSSSS !!!!!

I ported the dhd module from openelec kernel sources to odroidC2 sources


[ 103.646591] cfg80211: Calling CRDA to update world regulatory domain
[ 103.845046] cfg80211: World regulatory domain updated:
[ 103.845057] cfg80211: DFS Master region: unset
[ 103.845061] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 103.845067] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 103.845071] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 103.845075] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm)
[ 103.845079] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 103.845083] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 103.845087] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm)
[ 103.845091] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm)
[ 103.845095] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm)
[ 106.251264] dhd_module_init: in
[ 106.251275] [wifi_setup_dt] wifi_setup_dt
[ 106.251309] [wifi_setup_dt] interrupt_pin(235)
[ 106.251322] [wifi_setup_dt] power_on_pin(234)
[ 106.251327] ======== bcm_wlan_set_plat_data ========
[ 106.251331] host_oob_irq: 100
[ 106.251335] host_oob_irq_flags=1044
[ 106.251338] dhd_wifi_platform_load: Enter
[ 106.251351] Power-up adapter 'DHD generic adapter'
[ 106.251355] wifi_platform_set_power = 1
[ 106.251359] ======== PULL WL_REG_ON HIGH! ========
[ 106.251365] [extern_wifi_set_enable] WIFI Disable! 234
[ 106.451382] [extern_wifi_set_enable] WIFI Enable! 234
[ 106.956249] wifi_platform_bus_enumerate device present 1
[ 106.956256] ======== Card detection to detect SDIO card! ========
[ 106.957315] [aml_sd_emmc_irq] sdio: resp_timeout,vstat:0x2800,virqc:3fff

[ 106.957340] aml_sd_emmc_data_thread 2211 sdio: cmd:52
[ 106.958313] [aml_sd_emmc_irq] sdio: resp_timeout,vstat:0x2800,virqc:3fff

[ 106.958323] aml_sd_emmc_data_thread 2211 sdio: cmd:52
[ 106.962778] [aml_sd_emmc_irq] sdio: resp_timeout,vstat:0x2800,virqc:3fff

[ 106.962787] aml_sd_emmc_data_thread 2211 sdio: cmd:8
[ 106.977647] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 106.979952] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 106.982257] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 106.986435] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 107.119395] sdio: new high speed SDIO card at address 0001
[ 107.119401] sdio: clock 50000000, 4-bit-bus-width

[ 107.119610] [sdio_reinit] finish
[ 107.135841] bcmsdh_register: register client driver
[ 107.135924] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 107.135980] bcmsdh_sdmmc: bcmsdh_sdmmc_probe Enter
[ 107.135985] bus num (host idx)=0, slot num (rca)=1
[ 107.135989] found adapter info 'DHD generic adapter'
[ 107.135999] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc001beafb8, size=139264
[ 107.136003] success alloc section 3, size 139264
[ 107.136078] alloc static buf at ffffffc034b00000!
[ 107.136083] 1 bcmdhd_mem_prealloc: section=4, wlan_static_skb=ffffffc001f09bb0
[ 107.136086] success alloc section 4, size 0
[ 107.136426] dhdsdio_probe : no mutex held. set lock
[ 107.136519] F1 signature read @0x18000000=0x1540a9a6
[ 107.138696] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4
[ 107.139467] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[ 107.139577] 4 bcmdhd_mem_prealloc: section=7, wlan_mem_array[4]=ffffffc034ad8000
[ 107.139581] success alloc section 7, size 26160
[ 107.139610] dhd_conf_set_chiprev: chip=0xa9a6, chiprev=0
[ 107.139646] dhd_conf_set_conf_path_by_nv_path: config_path=/lib/firmware/config.txt
[ 107.146805] dhd_conf_read_config: Ignore config file /lib/firmware/config.txt
[ 107.146842] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc001beaf88, size=10416
[ 107.146847] success alloc section 0, size 10416
[ 107.147149] 2 bcmdhd_mem_prealloc: section=5, wlan_static_scan_buf0=ffffffc034b60000
[ 107.147154] success alloc section 5, size 65536
[ 107.147742] wl_create_event_handler(): thread:wl_event_handler:5f0 started
[ 107.147780] tsk Enter, tsk = 0xffffff80009fdaa8
[ 107.148296] dhd_attach(): thread:dhd_watchdog_thread:5f1 started
[ 107.150195] dhd_attach(): thread:dhd_dpc:5f3 started
[ 107.150211] dhd_dpc_thread: set dpc_cpucore 0 from config.txt
[ 107.150270] dhd_attach(): thread:dhd_rxf:5f4 started
[ 107.150282] dhd_deferred_work_init: work queue initialized
[ 107.150296] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc001beaf98, size=10396
[ 107.150300] success alloc section 1, size 10396
[ 107.150310] 7 bcmdhd_mem_prealloc: wlan_mem_array[section].mem_ptr=ffffffc001beafa8, size=65536
[ 107.150314] success alloc section 2, size 65536
[ 107.150524] dhdsdio_probe_init: set use_rxchain 0 from config.txt
[ 107.160069] Dongle Host Driver, version 1.201.59.5 (r506368)
Compiled in drivers/net/wireless/bcmdhd
[ 107.162083] Register interface [wlan0] MAC: 94:a1:a2:f5:70:af

[ 107.162098] dhd_prot_ioctl : bus is down. we have nothing to do
[ 107.162165] bcmsdh_oob_intr_unregister: Enter
[ 107.162170] bcmsdh_oob_intr_unregister: irq is not registered
[ 107.162179] dhd_txglom_enable: enable 0
[ 107.162182] dhd_bus_devreset: WLAN OFF DONE
[ 107.162224] wifi_platform_set_power = 0
[ 107.162228] ======== PULL WL_REG_ON LOW! ========
[ 107.162234] dhdsdio_probe : the lock is released.
[ 107.162304] dhd_module_init: Exit err=0
[ 107.231421] dhd: version magic '3.14.29 SMP mod_unload aarch64' should be '3.14.29 SMP preempt mod_unload aarch64'
[ 107.231425] dhd: version magic '3.14.29 SMP mod_unload aarch64' should be '3.14.29 SMP preempt mod_unload aarch64'
[ 107.277428] dhd_open: Enter ffffffc022bd3000
[ 107.277443]
Dongle Host Driver, version 1.201.59.5 (r506368)
Compiled in drivers/net/wireless/bcmdhd
[ 107.277449] wl_android_wifi_on in 1
[ 107.277454] wl_android_wifi_on in 2: g_wifi_on=0
[ 107.277458] wifi_platform_set_power = 1
[ 107.277462] ======== PULL WL_REG_ON HIGH! ========
[ 107.277479] [extern_wifi_set_enable] WIFI Disable! 234
[ 107.479316] [extern_wifi_set_enable] WIFI Enable! 234
[ 107.986233] sdio_reset_comm():
[ 108.003631] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 108.005938] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 108.008387] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 108.012534] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 108.143797]

dhd_bus_devreset: == WLAN ON ==
[ 108.143891] F1 signature read @0x18000000=0x1540a9a6
[ 108.145929] F1 signature OK, socitype:0x1 chip:0xa9a6 rev:0x0 pkg:0x4
[ 108.146863] DHD: dongle ram size is set to 524288(orig 524288) at 0x0
[ 108.147085] dhdsdio_probe_init: set use_rxchain 0 from config.txt
[ 108.147151] dhd_conf_read_config: Ignore config file /lib/firmware/config.txt
[ 108.147160] dhd_conf_set_fw_name_by_chip: firmware_path=/lib/firmware/fw_bcm43438a0.bin
[ 108.147165] Final fw_path=/lib/firmware/fw_bcm43438a0.bin
[ 108.147168] Final nv_path=/lib/firmware/nvram.txt
[ 108.147171] Final conf_path=/lib/firmware/config.txt
[ 108.188708] NVRAM version: AP6212_NVRAM_V1.0_20140603
[ 108.189185] dhdsdio_write_vars: Download, Upload and compare of NVRAM succeeded.
[ 108.244632] dhd_bus_init: enable 0x06, ready 0x06 (waited 0us)
[ 108.244726] bcmsdh_oob_intr_register: Enter
[ 108.244730] bcmsdh_oob_intr_register: HW_OOB enabled
[ 108.244734] bcmsdh_oob_intr_register OOB irq=100 flags=414
[ 108.244757] bcmsdh_oob_intr_register: enable_irq_wake
[ 108.244762] bcmsdh_oob_intr_register: enable_irq_wake failed with -6
[ 108.245982] dhd_conf_set_band: Set band 0
[ 108.246164] dhd_preinit_ioctls: Set tcpack_sup_mode 0
[ 108.248892] Firmware up: op_mode=0x0005, MAC=94:a1:a2:f5:70:af
[ 108.248899] dhd_conf_set_country: Set country CN, revision 0
[ 108.312878] Country code: CN (CN/0)
[ 108.313368] dhd_conf_set_roam: Set roam_off 1
[ 108.322737] Firmware version = wl0: Jul 18 2014 18:24:48 version 7.10.226.54.x2 (A0 Station) FWID 01-2faae407
[ 108.322745] Driver: 1.201.59.5 (r506368)
Firmware: wl0: Jul 18 2014 18:24:48 version 7.10.226.54.x2 (A0 Station) FWID 01-2faae407
[ 108.322752] dhd_txglom_enable: enable 0
[ 108.322756] dhd_conf_set_disable_proptx: set disable_proptx 0
[ 108.324527] dhd_wlfc_hostreorder_init(): successful bdcv2 tlv signaling, 64
[ 108.324903] wl_android_wifi_on: Success
[ 108.395619] dhd_open: Exit ret=0
[ 108.498285] WLC_E_IF: NO_IF set, event Ignored
[

odroid@odroid64:/lib/modules/3.14.29/kernel/drivers/amlogic/wifi/broadcom/bcmdhd_1_201_59_x$ iw
iw iwconfig iwevent iwgetid iwlist iwpriv iwspy
odroid@odroid64:/lib/modules/3.14.29/kernel/drivers/amlogic/wifi/broadcom/bcmdhd_1_201_59_x$ iwconfig
eth0 no wireless extensions.

wlan0 IEEE 802.11 Access Point: Not-Associated
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 invalid crypt:0 invalid misc:0

lo no wireless extensions.


odroid@odroid64:~$ sudo iwlist wlan0 scan
wlan0 Scan completed :
Cell 01 - Address: 00:37:B7:51:749
ESSID:"SFR-74d3"
Mode:Managed
Frequency=2.412 GHz (Channel 1)
Quality:1/5 Signal level:-83 dBm Noise level:0 dBm
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
Encryption keyn
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s



odroid@odroid64:~$ ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 94:a1:a2:f5:70:af
inet addr:192.168.10.53 Bcast:192.168.10.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:19 errors:0 dropped:2 overruns:0 frame:0
TX packets:14 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:2654 (2.6 KB) TX bytes:2806 (2.8 KB)

[Koxx]

Oh yes, one more thing... Thanks a lot for your help guys

[Koxx]

The MiniMX 1G/8G has an AP6212.

Ok, let's restart ...

I installed the distrib as described :
http://freaktab.com/forum/tv-player-...thod-and-files

I extract the MiniMX dtb as described and placed it on sdcard as dtb.img (as loaded in s905_autoscript, in /media/boot ... sdcard) :
http://www.cnx-software.com/2014/05/...irmware-files/

I took the kernel from here :

odroid@odroid64:~$ git clone --depth 1 https://github.com/hardkernel/linux.git -b odroidc2-3.14.y

I prepared the kernel with "odroidc2_defconfig".

odroid@odroid64:~/linux$ make odroidc2_defconfig

Added wifi 80211 / am_wifi as module & snd_aml_m8

http://pastebin.com/TnsF2QfW

diff :
CONFIG_SND_AML_M8=y
CONFIG_AM_WIFI=y
CONFIG_AM_WIFI_SD_MMC=y
CONFIG_AM_WIFI_USB=y
CONFIG_DHD_USE_STATIC_BUF=y
CONFIG_BT_DEVICE=y
CONFIG_BRCMSMAC=m
CONFIG_BRCMFMAC_SDIO=y
CONFIG_BCMA=m
CONFIG_BCMA_BLOCKIO=y

I removed the kernel 'plus' sign in the kernel version to get '3.14.29' and not '3.14.29+' (to avoid module issue when loading)
http://stackoverflow.com/questions/1...kernel-version

then compiled (and didn't copy dtd file since I alredy copied it):

odroid@odroid64:~/linux$ LOCALVERSION= make -j4
odroid@odroid64:~/linux$ sudo make modules_install
odroid@odroid64:~/linux$ sudo cp -f arch/arm64/boot/Image /media/boot/

I obtain those modules :
INSTALL net/wireless/cfg80211.ko
INSTALL net/wireless/lib80211.ko
INSTALL net/wireless/lib80211_crypt_ccmp.ko
INSTALL net/wireless/lib80211_crypt_tkip.ko
INSTALL net/wireless/lib80211_crypt_wep.ko
INSTALL drivers/net/wireless/brcm80211/brcmfmac/brcmfmac.ko
INSTALL drivers/net/wireless/brcm80211/brcmsmac/brcmsmac.ko
INSTALL drivers/net/wireless/brcm80211/brcmutil/brcmutil.ko

I set the /lib/firmware/nvram.txt file with the AP6212:

http://pastebin.com/JDbXhZrD

I have the firmware in place in /lib/firmware/ (from openelec MiniMX):
-rw-r--r-- 1 root root 34700 Apr 18 13:45 fw-0a5c_21e8.hcd
-rw-r--r-- 1 root root 34573 Apr 18 13:45 fw-0a5c_21ec.hcd
-rw-r--r-- 1 root root 309352 Apr 18 13:45 fw_bcm43438a0_apsta.bin
-rw-r--r-- 1 root root 326074 Apr 18 13:45 fw_bcm43438a0.bin
-rw-r--r-- 1 root root 326074 Apr 18 13:45 fw_bcm43438a0_p2p.bin
-rw-r--r-- 1 root root 4178 Apr 18 13:45 LICENCE.broadcom_bcm43xx
-rw-r--r-- 1 root root 956 Apr 18 13:45 nvram.txt

and let's go :
odroid@odroid64:~/linux$ sudo reboot

still nothing ...

dmesg:

http://pastebin.com/BuKyASYz

[balbes150]

What on Your console chip ? ap6330 ? Then you need to use the settings nvram.txt from your consoles. The files you need you can take from this image

http://www.amlinux.ru/image/devel/

MiniMX r22293

[Koxx]

that seems good ...

[ 0.213827] [wifi_dev_probe] wifi_dev_probe
[ 0.213838] [wifi_dev_probe] wifi_dt : interrupt_pin=
[ 0.213871] [wifi_dev_probe] wifi_dt : irq_num=null
[ 0.213880] [wifi_dev_probe] wifi_dt : irq_trigger_type=GPIO_IRQ_LOW
[ 0.213891] [wifi_dev_probe] wifi_dt : power_on_pin=
[ 0.213903] [wifi_dev_probe] set pwm as 32k output
[ 0.213949] [wifi_dev_probe] dhd_static_buf setup
[ 0.213964] 1 bcmdhd_init_wlan_mem: wlan_static_skb[0]=ffffffc034a0d600, size=3760
[ 0.213979] 1 bcmdhd_init_wlan_mem: wlan_static_skb[1]=ffffffc034a0d700, size=3760
[ 0.213992] 1 bcmdhd_init_wlan_mem: wlan_static_skb[2]=ffffffc034a0d800, size=3760
[ 0.214006] 1 bcmdhd_init_wlan_mem: wlan_static_skb[3]=ffffffc034a0d900, size=3760
[ 0.214019] 1 bcmdhd_init_wlan_mem: wlan_static_skb[4]=ffffffc034a0da00, size=3760
[ 0.214033] 1 bcmdhd_init_wlan_mem: wlan_static_skb[5]=ffffffc034a0db00, size=3760
[ 0.214047] 1 bcmdhd_init_wlan_mem: wlan_static_skb[6]=ffffffc034a0dc00, size=3760
[ 0.214060] 1 bcmdhd_init_wlan_mem: wlan_static_skb[7]=ffffffc034a0dd00, size=3760
[ 0.214074] 2 bcmdhd_init_wlan_mem: wlan_static_skb[8]=ffffffc034a0de00, size=7856
[ 0.214088] 2 bcmdhd_init_wlan_mem: wlan_static_skb[9]=ffffffc034a0df00, size=7856
[ 0.214108] 2 bcmdhd_init_wlan_mem: wlan_static_skb[10]=ffffffc034a0f000, size=7856
[ 0.214122] 2 bcmdhd_init_wlan_mem: wlan_static_skb[11]=ffffffc034a0f100, size=7856
[ 0.214136] 2 bcmdhd_init_wlan_mem: wlan_static_skb[12]=ffffffc034a0f200, size=7856
[ 0.214149] 2 bcmdhd_init_wlan_mem: wlan_static_skb[13]=ffffffc034a0f300, size=7856
[ 0.214162] 2 bcmdhd_init_wlan_mem: wlan_static_skb[14]=ffffffc034a0f400, size=7856
[ 0.214175] 2 bcmdhd_init_wlan_mem: wlan_static_skb[15]=ffffffc034a0f500, size=7856
[ 0.214190] 3 bcmdhd_init_wlan_mem: wlan_static_skb[16]=ffffffc034a0f600, size=16048
[ 0.214203] 4 bcmdhd_init_wlan_mem: wlan_mem_array[0]=ffffffc034a0d600, size=20504
[ 0.214218] 4 bcmdhd_init_wlan_mem: wlan_mem_array[1]=ffffffc034a0d700, size=20504
[ 0.214232] 4 bcmdhd_init_wlan_mem: wlan_mem_array[2]=ffffffc034a0d800, size=81944
[ 0.214248] 4 bcmdhd_init_wlan_mem: wlan_mem_array[3]=ffffffc034a0d900, size=163864
[ 0.214261] 4 bcmdhd_init_wlan_mem: wlan_mem_array[4]=ffffffc034a0da00, size=20504
[ 0.214275] 4 bcmdhd_init_wlan_mem: wlan_mem_array[5]=ffffffc034a0db00, size=81944
[ 0.214290] 5 bcmdhd_init_wlan_mem: wlan_static_scan_buf0=ffffffc034b80000, size=65536
[ 0.214303] 6 bcmdhd_init_wlan_mem: wlan_static_scan_buf1=ffffffc034b90000, size=65536
[ 0.214314] bcmdhd_init_wlan_mem: WIFI MEM Allocated
[ 0.214322] [wifi_dev_probe] interrupt_pin=235
[ 0.214330] [wifi_dev_probe] irq_num=100, irq_trigger_type=1
[ 0.214339] [wifi_dev_probe] power_on_pin=234
[ 0.214347] [wifi_dev_probe] clock_32k_pin=0


and bad ..

[ 3.486077] [wifi_power_probe] Error: can not read string
[ 3.486087] [wifi_power_probe] wifi_dev_probe : there is no DTS file!

what's next ?

[Koxx]

ok, firmware copied.

for modules, I found this /etc/ after unsquashfs
lrwxrwxrwx 1 root root 31 avril 18 19:37 modules-load.d -> /storage/.config/modules-load.d
lrwxrwxrwx 1 root root 27 avril 18 19:37 modprobe.d -> /storage/.config/modprobe.d

both are nearly empty. nothing to use in this.

I recompiled the kernel to be sure I'll have :
/lib/modules/3.14.29/kernel/net/wireless/cfg80211.ko

I also copied :
/lib/modules/3.14.29/kernel/drivers/amlogic/wifi/broadcom/bcmdhd_1_201_59_x

I think something is missing since there is nothing to load the module...

here is my dmesg :

http://pastebin.com/EXcbVrPU

[balbes150]

Yes, it is about the dhd module

[Koxx]

thanks !
is the bcmdhd module needed ? because it's not in the current odordoic2 kernel :/
I'll try that tomorrow

[balbes150]

Try it this way.

copy the directory /lib/firmware/brcm from the latest version Openelec and all its contents in /lib/firmware.
copy the contents of the files /etc/modprobe.d and /etc/modules-load.d into files with the same names.
I'm not sure it will help. We need to see how the 80211 module included in the kernel.

[Koxx]

Kodi is running great.
Now, I am trying to add the 'bcmdhd' drivers & firmware to the kernel ... but I have no clue how to do that.
I just managed to get the firmware from OpenElec distrib.
How can I add this to the kernel build ?

[trebor]

Excellent, never give up good to see
Cheers

[Koxx]

my god ... after 5 hours of digging, I found a hack :
su -c 'echo "audio_on" > /sys/class/amhdmitx/amhdmitx0/config'

it enable the sound on HDMI !

kodi is now fully working.
tomorrow : network routing, transmission and openvpn.

[Koxx]

it seems almost good :


odroid@odroid64:~$ aplay -l
**** List of PLAYBACK Hardware Devices ****
xcb_connection_has_error() returned true
card 0: AMLM8AUDIO [AML-M8AUDIO], device 0: I2S.35 dummy-0 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: AMLM8AUDIO [AML-M8AUDIO], device 1: SPDIF.36 dit-hifi-1 []
Subdevices: 1/1
Subdevice #0: subdevice #0
card 0: AMLM8AUDIO [AML-M8AUDIO], device 2: PCM.37 pcm2bt-pcm-2 []
Subdevices: 1/1
Subdevice #0: subdevice #0


odroid@odroid64:~$ aplay /mnt/pchome-mydatas/series/Media-Convert_test6_PCM_Stereo_VBR_16SS_8000Hz.wav
xcb_connection_has_error() returned true
xcb_connection_has_error() returned true
Playing WAVE '/mnt/pchome-mydatas/series/Media-Convert_test6_PCM_Stereo_VBR_16SS_8000Hz.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo


[ 888.517546] [aml-i2s-dai]i2s dma ffffff80007c2000,phy addr 914751488,mode 0,ch 2
[ 888.517558] ----aml_hw_iec958_init,runtime->rate=48000,sample_rate=4--
[ 888.517562] aml_set_spdif_clk rate
[ 888.517574] divider=20,frac=33920000,SDMval=5654
[ 888.517585] set normal 512 fs /4 fs
[ 888.517592] iec958 mode PCM16
[ 888.517599] IEC958 16bit
[ 888.517604] hdmitx: audio: aout notify rate 48000
[ 888.517608] hdmitx: audio: aout notify size 16
[ 888.517611] 958 with i2s
[ 888.517716] speaker_events--mute =1
[ 888.523636] [aml-i2s-dai]i2s dma ffffff80007c2000,phy addr 914751488,mode 0,ch 2
[ 888.523641] ----aml_hw_iec958_init,runtime->rate=48000,sample_rate=4--
[ 888.523645] aml_set_spdif_clk rate
[ 888.523652] divider=20,frac=33920000,SDMval=5654
[ 888.523661] set normal 512 fs /4 fs
[ 888.523667] iec958 mode PCM16
[ 888.523673] IEC958 16bit
[ 888.523677] hdmitx: audio: aout notify rate 48000
[ 888.523680] hdmitx: audio: aout notify size 16
[ 888.523684] 958 with i2s
[ 888.524068] aiu i2s playback enable



here is my /etc/asound.conf


pcm.!default {
type plug
slave {
pcm "hw:0,2"
format S32_LE
}
}

still no sound :/
any idea ?