If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
- WiFi - BCM4335 (Support for other WiFi chips on request)
- RAM - LPDDR3
- eMMC - 16g
- DVB-Tuner - AVL6862 (currently not supported, no DTV support)
Important - Switching from Android 6/7 to Android 9 must be carried out via UBT.
If you already have Android 9 installed, you can perform an SDcard update.
This assembly is intended for set-top boxes with the Fn-Link 6222b-srb WiFi chip (the same RTL8222BS).
The version for BCM4324 (AP62x2) chips is in testing and will be released a little later.
Updated u-boot loader
——————————————- ///
- Added support for P211 (S905L) platform
- Optimized RAM timing
- Modified BL30 blob (special thanks to John Red for providing the patch), for an error in the incorrect determination of the chip id, which prevents further random MAC generation, the execution of the BL33 main bootloader code, leading to a cyclic reboot of the processor.
Firmware based on Android 9, compiled from scratch
———————————————————————————— ///
- Added support for Megaphone and Beeline consoles by default, configurations are hardcoded in dtb (not tested yet)
- Updated GAPPS
- Fixed some incompatibilities leading to reboot of the console
Please test. Logs are always welcome.
- Initial installation via UBT only. Subsequent installations can be done using
mSD card
Also special thanks to @banderkin for providing logs and tireless testing.
i intall S905L2 every thing ok scucessfull 100%
but when start...only screen dark....hdmi connected
thank so much
may be only used for Q5
not for another box android has cpu S905L2
phankhanh86
The bootloader in this firmware is designed for S905L devices with 1G RAM. If you have a 2G device you will get a black screen. But I'm not sure if you actually have a S905L2 SoC, otherwise the installation would fail.
phankhanh86
The bootloader in this firmware is designed for S905L devices with 1G RAM. If you have a 2G device you will get a black screen. But I'm not sure if you actually have a S905L2 SoC, otherwise the installation would fail.
no installation seccessfull 100% But tv still black screen
can you change it for s905L2
thank so much
So could i Flash one od those 2 firmware on my s905d 1gb ddr3 box? And which od those 2 firmware first for s905d 2gb or or second s905l 1gb?
does DVB-T work on those firmwares?
thanks
So could i Flash one od those 2 firmware on my s905d 1gb ddr3 box? And which od those 2 firmware first for s905d 2gb or or second s905l 1gb?
does DVB-T work on those firmwares?
thanks
S905D 1G version is equipped with a 3D Nand (L95B). The bootloader driver supports this type of memory, but I was unable to test the kernel driver due to the lack of a test device. By default, only emmc support is activated, an installation on a 3D Nand device will fail.
DVB support has been compiled into this kernel, but AVL6762 is not supported.
You will need a different build for the S905L.
By default, only emmc support is activated, an installation on a 3D Nand device will fail.
Thanks for answer but i am not so good it technic so if i Flash your firmware with usb burning Tool on my s905d 1gb would it work or it will be bricked? Thanks
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment