RK3328 Firmware Center RTL8723 , AP6255 , SV6051 , IT6334 AND MORE (Stock-ROMs , Custom-ROMs by Silver)

[klinyermont]

Hello, I have an MX10 PRO with MXQ RK3328 D4 board v1.3 20180306 and on the wifi bt chip it says HK6334Q and I don't know what the firmware is, I have placed several of H6 MAX and HK1 MAX and they work without wifi and without bluetooth. what is on the net for that model does not work, it remains unbrick. any suggestions I appreciate

[Silver]

Thank you very much Silver. You are a lifesaver. I was able to get back to life my "MX9 max" tv box ( Rockchip RK3328 4core ARM Cortex A53 64-bit CPU/ 5core ARM Mali-450 GPU/ 2GB RAM/ 16GB ROM), (MINI RK3328_D4, REV:1.0, 2017 09 07)

I used "RTL8723" (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) firmware. TV box is rooted and working perfect. WIFI also works.

I have used "{ROM} PoisonATV RK3328" and "a9s_rk3328_d4_rtl8723_20180705_r1(mx9pro ??kodi???)" firmware before. They both installed properly, but after I unplug power, PoisonATV did not boot at all and the other ROM wiped everything and presented the initial setup every time reboot.

Here are my steps to flash the firmware from 'Silver' (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) :

1. Install Rockchip_DriverAssitant_v4.4 or v4.8
2. Open "rkdev tool - AndroidTool_Release_v2.51" and goto 'Upgrade Firmware' tab
3. Click 'Firmware' and locate the img file
4. Remove screws of the TVbox. Refer to the image attached below and find the copper dots which are necessary to short-circuit to enter MASKROM mode.
5. Use a wire or a conductor to connect the two dots. While doing that, connect the male-male USB cable to PC and USB 2 port of the tv box. AndroidTool will show "Found One MASKROM Device" immediately. Remove the Short-circuiting conductor.
6. Click 'EraseFlash'
7. Click 'Upgrade'
8. After the upgrade is finished, remove the USB cable.
9. Connect HDMI cable
10. Connect power cable (sometimes, you might have to hold the av-reset pin before connecting the power cable. but I didn`t have to do that)
11. Boot animation will appear within few seconds. If the display goes to standby mode, remove and replug the power cable.
12. the android logo will appear. then wait.....
13. Done !!!
14. Let me know if this helps.

Pins to Short-circuit:

No problem, thats why i uploaded the ROMs so people like you have a chance of fixing the box

[levin44]

I have seen many users bricking their RK3328 TV box with incorrect firmware.
In this thread i will supply some IMG files for you all so you can reflash your box with working wifi/bt drivers

This includes 2 firmwares i have customized with preinstalled apps some patches and root

......

Confirmed working on:

MX9Pro
A5XMAX
MX10
V88 Piano
...more to come

Please test firmwares and reply back here so others know what works for what box.

-Silver

Thank you very much Silver. You are a lifesaver. I was able to get back to life my "MX9 max" tv box ( Rockchip RK3328 4core ARM Cortex A53 64-bit CPU/ 5core ARM Mali-450 GPU/ 2GB RAM/ 16GB ROM), (MINI RK3328_D4, REV:1.0, 2017 09 07)

I used "RTL8723" (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) firmware. TV box is rooted and working perfect. WIFI also works.

I have used "{ROM} PoisonATV RK3328" and "a9s_rk3328_d4_rtl8723_20180705_r1(mx9pro ??kodi???)" firmware before. They both installed properly, but after I unplug power, PoisonATV did not boot at all and the other ROM wiped everything and presented the initial setup every time reboot.

Here are my steps to flash the firmware from 'Silver' (rk3328_d4_7.1_rtl8723bs_20180705_r1_root.img) :

1. Install Rockchip_DriverAssitant_v4.4 or v4.8
2. Open "rkdev tool - AndroidTool_Release_v2.51" and goto 'Upgrade Firmware' tab
3. Click 'Firmware' and locate the img file
4. Remove screws of the TVbox. Refer to the image attached below and find the copper dots which are necessary to short-circuit to enter MASKROM mode.
5. Use a wire or a conductor to connect the two dots. While doing that, connect the male-male USB cable to PC and USB 2 port of the tv box. AndroidTool will show "Found One MASKROM Device" immediately. Remove the Short-circuiting conductor.
6. Click 'EraseFlash'
7. Click 'Upgrade'
8. After the upgrade is finished, remove the USB cable.
9. Connect HDMI cable
10. Connect power cable (sometimes, you might have to hold the av-reset pin before connecting the power cable. but I didn`t have to do that)
11. Boot animation will appear within few seconds. If the display goes to standby mode, remove and replug the power cable.
12. the android logo will appear. then wait.....
13. Done !!!
14. Let me know if this helps.

Pins to Short-circuit:

[freddy]

Hello! I m pretty new here and to installing custom firmwares to tv boxes. I got v88 4K tv box and I thought it was too slow and wanted to try these firmwares. My question is that i got an error message while using androidtool saying "Chip check fail" when i tried to install "rk3328_d4_9.0_rtl8723bs_20181128_r1.img"

So why do i get this error?

Thx in advance for replies

V-88 = Rockchip RK 3229

Move/Navigate to there

Roms there to test

Good Luck

Happy Testing

[deathphantom]

Hello! I m pretty new here and to installing custom firmwares to tv boxes. I got v88 4K tv box and I thought it was too slow and wanted to try these firmwares. My question is that i got an error message while using androidtool saying "Chip check fail" when i tried to install "rk3328_d4_9.0_rtl8723bs_20181128_r1.img"

So why do i get this error?

Thx in advance for replies

[Silver]

Hello my android box tv is a H96 Max H2 with RK3328 CPU and wifi chipset HS2734A.
I think IT6334 chipset is the same ????

Never had that box, try firmware at your own risk, do backup before flash!

[snyker]

Hello my android box tv is a H96 Max H2 with RK3328 CPU and wifi chipset HS2734A.
I think IT6334 chipset is the same ????

[Atif Munir]

Hello Silver
i flash your custom rom Ap6255 in my Piano v88 box have 4gb ram 16gb rom, Every thing working fine, thank you for nice work, i am new user and ready to test your upcoming new rom in my box,

[251643711]

My box is 8723, brushed wifi and bt not enabled

[Silver]

Hi, I flashed this ROM on Beelink A1.

The Box booted up but Wifi/Bluetooth is Not Working.

Is it suitable for rtl8821cu.

Thanks

Look into OP i have listed working wifichip, it does not work for rtl 8821cu

[tv2020]

Hi, I flashed this ROM on Beelink A1.

The Box booted up but Wifi/Bluetooth is Not Working.

Is it suitable for rtl8821cu.

Thanks

[italorecife]

Hello do you have any ATV rom/firmware for RK3228 T9 (Alfawise t9)?

[Silver]

Guys if you have problems getting the firmware to load up in your box, please try to flash only system.img (use correct android version) in your box leave everything else stock, i cannot guarantee all things work but u could get it to boot with a modified system.img, use Androidtool and correct offset from stockrom from your box to flash it, some manufacturers have build in locks into bootloader ect. to prevent altering firmware, i have posted guide to unlock bootloader, may help in some cases.

[billi69]

same error Prepare idb fail

[Silver]

try FactoryTool 1.45e or other versio of androidtool