Failed Flash of 1.5 after 30% and now unit will not boot past Android with Exclamation mark

[cmakar]

Can someone please tell me how to force the Imito Mx1 into flash mode IF the 1.5 flash failed after 30%? I cannot find a way to do it.

I attached the 1.5 boot screen and the error that I get. I know this is normal to see with a failed load. Please help.

[davphi338]

Can someone please tell me how to force the Imito Mx1 into flash mode IF the 1.5 flash failed after 30%? I cannot find a way to do it.

I attached the 1.5 boot screen and the error that I get. I know this is normal to see with a failed load. Please help.

I had same sysmptons but after changing libstagefright.so file. I'm not sure exactly what hardware you have but if there is a small hole on the side of the casing, it is a rest button to put the device into flash mode. Put a small piece of wire/pin into hole and you should feel the reset button. Hold it down and at the same time connect usb cable to PC (otg port not charging one) after 3-5 secs release reset button. Your PC should ping after a few seconds as it sees the device. Since you already have the drivers installed it should see the device in device manager. You should now be able to re-flash.

If you do not have a rest button if think you perform the same procedure but short between 2 pins on the flash chip. I have an MK809ii and the pins are 6/7. I was able to put a locked up device back into flash mode following both procedures.

[cmakar]

Bluetooth pairing of Logitech Revue Keyboard with Imito MX1????

Thank you very much for this information and I was successfully able to update to 1.7a. Now my wifi is actually useable and can stream movies.

Once other question - I have the logitech Revue and I wanted to disconnect the Bluetooth kepyboard from it and connect it to the Imito MX1 - any idea how to do that?

The mini keyboard with USB connected that came with the MX1 barely can go 3 feet and looses connection - and is still sluggish.

I like the review but stuck on 3.2 and the fan it now obnoxiously loud.

I had same sysmptons but after changing libstagefright.so file. I'm not sure exactly what hardware you have but if there is a small hole on the side of the casing, it is a rest button to put the device into flash mode. Put a small piece of wire/pin into hole and you should feel the reset button. Hold it down and at the same time connect usb cable to PC (otg port not charging one) after 3-5 secs release reset button. Your PC should ping after a few seconds as it sees the device. Since you already have the drivers installed it should see the device in device manager. You should now be able to re-flash.

If you do not have a rest button if think you perform the same procedure but short between 2 pins on the flash chip. I have an MK809ii and the pins are 6/7. I was able to put a locked up device back into flash mode following both procedures.

[cmakar]

Logitech Revue keyboard is NOT bluetooth

Unless I am reading something wrong, the Logitech Revue K700 keyboard is NOT bluetooth and connects to the revue through an embedded receiver in the revue. So there will be no way to pair this unless someone tells me it has bluetooth otherwise - if it doesnt, can I buy a reciever for it?

Thank you very much for this information and I was successfully able to update to 1.7a. Now my wifi is actually useable and can stream movies.

Once other question - I have the logitech Revue and I wanted to disconnect the Bluetooth kepyboard from it and connect it to the Imito MX1 - any idea how to do that?

The mini keyboard with USB connected that came with the MX1 barely can go 3 feet and looses connection - and is still sluggish.

I like the review but stuck on 3.2 and the fan it now obnoxiously loud.