I am trying to flash the Finless 1.7 on my MK 808 B but the windows 8 is not detecting my MK 808B. I enabled the connect to pc option, changed the storage mode to mass storage and tried turning ON/OFF USB debugging mode and still it doesn't work. Can anyone help me out please ?
-
-
Took me awhile aswell, try plugging the stick into your PC while having the reset button held down, release when plugged in, wait for the windows "ding". -
It's only detecting as a USB storage and when I press (reboot to flash) it says "msc device can't upgrade" and it shows flash mode failed when I press (flash rom). I manually installed the drivers but windows 8 always says its the most updated driver.Last edited by ndndr; 03 May 2013, 07:04.Comment
-
That is because your not in flash mode!
Use the reset button to enter flash mode from a stock ROM.
Bob"Pzebacz im, bo nie wiedzą, co czynią"
"Прости им, они не ведают, что творят"
"Perdona loro perché non sanno quello che fanno"
"Vergib ihnen, denn sie wissen nicht, was sie tun"
"Vergeef hen want ze weten niet wat ze doen"
"Pardonne-leur car ils ne savent pas ce qu'ils font"
"Perdónalos porque no saben que lo que hacen"
"Oprosti im, jer ne znaju što čine"
"Forgive them as they know not what they do"Comment
-
Originally posted by Finless View Post
Yes that's what I do, I press the reset button and then connect the USB OTG and I wait for like 10 sec.I never hear the ding sound, could it be that the windows 8 doesn't suppport the Mk808b drivers?Comment
-
Windows 8 does in fact support the flash tool and there are win 8 drivers!
I think you have a bad USB cable or something like that. You ARE plugged in the OTG port and not the read power only port correct?
Bob"Pzebacz im, bo nie wiedzą, co czynią"
"Прости им, они не ведают, что творят"
"Perdona loro perché non sanno quello che fanno"
"Vergib ihnen, denn sie wissen nicht, was sie tun"
"Vergeef hen want ze weten niet wat ze doen"
"Pardonne-leur car ils ne savent pas ce qu'ils font"
"Perdónalos porque no saben que lo que hacen"
"Oprosti im, jer ne znaju što čine"
"Forgive them as they know not what they do"Comment
-
Originally posted by Finless View Post
Yes I tried a different cable and I am using the OTG port, still having the same issue. I tried doing the alternate way by checking for pink and green light and that didn't work also.Comment
-
Re: Windows 8 not detecting MK808B
I supose you maintain the reset button pressed while you connect the usb to OTG. I have installed Windows 8 x64 and no problems.REMEMBER, YOUR FEEDBACK IS VERY IMPORTANT TO US.My devices:
Minix Neo X7; Minix Neo X8-H , Minix Neo Z64W & Z64 (Sponsored by Minix)
MK902 & MK902II(Sponsored by RKM)
Beelink M8B & Beelink R89 (Sponsored by Beelink)
Tronsmart VEGA S89H (Sponsored by Gearbest.com)
MELE-PCG03 (Sponsored by Gearbest.com) Discount Coupon:MPCG03
Ainol Intel Z3735 MiniPC(Sponsored by Gearbest.com)
Thanks to them I can try to support your devices http://freaktab.com/core/images/smilies/wink.pngComment
-
Boot into your BIOS on your PC and see what USB settings you have. Try to setup USB 2.0 compatibility and legacy support. If your PC cannot see the device in flash mode then it is going to be something like this.
You cannot even get the PC to recognize the device which is VERY STRANGE... it should bong or see some kind of hardware plugged in. Maybe try a rear motherboard USB port etc...
Bob"Pzebacz im, bo nie wiedzą, co czynią"
"Прости им, они не ведают, что творят"
"Perdona loro perché non sanno quello che fanno"
"Vergib ihnen, denn sie wissen nicht, was sie tun"
"Vergeef hen want ze weten niet wat ze doen"
"Pardonne-leur car ils ne savent pas ce qu'ils font"
"Perdónalos porque no saben que lo que hacen"
"Oprosti im, jer ne znaju što čine"
"Forgive them as they know not what they do"Comment
-
Windows 8 64 bit driver
I see that this problem is not solved because I have the same problem with windows 8 64 bitOriginally posted by Finless View Post
I took your advice but no success BoBComment
-
i hold in reset button button, and connect the cable to otg port.....wait 10 secs...let go of reset then press for a sec and let go of reset button again...Originally posted by ndndr View Post
this then finds the driversComment
-
Comment