Lollipop - Wasser Firmware for Tronsmart R68 with 100M LAN

[veralynn]

Hey Wasser. I just flashed my R68 to Your rom because someone said this would fix the DTS MASTER and Atmos to work.
But it didnt..
I can not get the DTS MASTER to my reciver and i have set settings to Passthrough and also in the R68 meny i have set the output to Hdmi bitstream.
I have no problem With these exact files streaming from my Mede8er to my Denon x4100.

Kodi talked about adding atmos, but nothing yet at least.
Is this something you can fix?

Also- To get 4K from netflix is there some way to spoof this Device to be a nvidia Shield or something that Netflix will send 4K content to?

Many thanks for answer and solutions!!
Greetings from Norway.

[brenas25]

Hi Wasser.
Are you gonna make rom for Gigabite ver. of Tronsmart r68? with working ethernet.Marry Xmas.

[amclean123]

I've often found that erasing the nand resolves any issues going to and from ROM's where there are issues.

Changes in bootloader version can also cause issues if there is a mismatch.

Thanks. I did a full erase and was still never able to back version to the Wasser rom. I can install the official tronsmart roms just fine.

[xwingfighter]

brenas25 and shiznit...thanks for the responses. I am actually quite pleased with the Wasser firmware; would be disappointed if there are no gigabit drivers available, but will continue using it over wifi as it solved the issues I had where the Kodi version couldn't be updated past 15.2rc1 and the ChrisB's Beast wouldn't load properly.

[shiznit]

Has anyone else experienced not being able to connect with ethernet after installing the latest Wasser firmware (3.1.2) on the R68 Meta Gigabit model? My wifi works fine, but I get all zeros in my ethernet properties even though the cable is plugged in and it is set to DHCP. Additionally, if I set the IP mode to static, it doesn't allow me to change any of the settings. Any assistance would be greatly appreciated.

I don't think wasser's ROM includes Ethernet drivers for the gigabit models, only the 100mbit models are supported

[brenas25]

I had the same but after flashed this everthing working O.K.

[ROM] Tronsmart Orion R68G_205L_151110.img ( Nov 28, 2015 )

Has anyone else experienced not being able to connect with ethernet after installing the latest Wasser firmware (3.1.2) on the R68 Meta Gigabit model? My wifi works fine, but I get all zeros in my ethernet properties even though the cable is plugged in and it is set to DHCP. Additionally, if I set the IP mode to static, it doesn't allow me to change any of the settings. Any assistance would be greatly appreciated.

[xwingfighter]

Has anyone else experienced not being able to connect with ethernet after installing the latest Wasser firmware (3.1.2) on the R68 Meta Gigabit model? My wifi works fine, but I get all zeros in my ethernet properties even though the cable is plugged in and it is set to DHCP. Additionally, if I set the IP mode to static, it doesn't allow me to change any of the settings. Any assistance would be greatly appreciated.

[bluesmanuk]

After spending hours trying to figure out the "Wait for Loader Fail" error I upgraded to the latest beta firmware on Tronsmart's website. This finally got around the issue. But it seems like the Factory Tool won't let me go backwards in rom version. I can't install old Tronsmart or older Wasser roms. Does anyone have any suggestions?

I've often found that erasing the nand resolves any issues going to and from ROM's where there are issues.

Changes in bootloader version can also cause issues if there is a mismatch.

[amclean123]

After spending hours trying to figure out the "Wait for Loader Fail" error I upgraded to the latest beta firmware on Tronsmart's website. This finally got around the issue. But it seems like the Factory Tool won't let me go backwards in rom version. I can't install old Tronsmart or older Wasser roms. Does anyone have any suggestions?

[Muyaar]

Wifi & Bluetooth is not working with this rom on Beelink i68. It's working with default Tronsmart Rom and also if build my own rom from sdk.

D/CommandListener( 190): Setting iface cfg
D/CommandListener( 190): Trying to bring down wlan0
D/CommandListener( 190): Clearing all IP addresses on wlan0
E/WifiMonitor( 478): killSupplicant p2ptrue init.svc.wpa_supplicant=unknown init.svc.p2p_supplicant=unknown
D/RkWifiCtrl( 478): check_wifi_chip_type_string: AP6335
D/RkWifiCtrl( 478): Kernel version is 3.10.
D/RkWifiCtrl( 478): Kernel version is 3.10.
D/WifiHW ( 478): wifi_start_supplicant: p2p_supplicant
D/WifiMonitor( 478): startMonitoring(wlan0) with mConnected = false
E/WifiHW ( 478): Unable to open connection to supplicant on "@android:wpa_wlan0": No such file or directory
I/wpa_supplicant( 2885): Successfully initialized wpa_supplicant: for broadcom wifi
I/wpa_supplicant( 2885): rfkill: Cannot open RFKILL control device
D/PowerManagerService( 478): screen time out
E/wpa_supplicant( 2885): Could not set interface wlan0 flags (UP): Operation not permitted
E/wpa_supplicant( 2885): nl80211: Could not set interface 'wlan0' UP
E/DrmService( 195): [wlan0] interface is not ready, wait 300000us
E/wpa_supplicant( 2885): wlan0: Failed to initialize driver interface
E/WifiHW ( 478): Supplicant not running, cannot connect
E/WifiHW ( 478): Supplicant not running, cannot connect
E/WifiHW ( 478): Supplicant not running, cannot connect

I have the same issue

Did you manage to fix this as I'm stuck

[Muyaar]

Hi

Sorry I am new to tronsmart and have an issue after flashing this firmware

I bought the box and my video was stuttering so thought I'd try this.

All went well but then when I tried it my wifi and Bluetooth stopped working.

Went back to stock, same issue

The WiFi switches on and back off without actually looking for signals. Same with Bluetooth.

I left the box off over night and switched it on and all of a sudden I could see wifi signals available.

Once I tried connecting it went back to the same same state as before.

Please help

[amclean123]

I was moving things around in my TV cabinet and plugged the wrong ac adapter into the R68 and killed it.

Sadly I've done that too.

[bluesmanuk]

How u fried that box?

I was moving things around in my TV cabinet and plugged the wrong ac adapter into the R68 and killed it.

[bajann]

How u fried that box?

[bluesmanuk]

What happens if i put Wasser ROM on Tronsmart R68 100M version (the first bulk that came out with 100M Ethernet and not the new Gigabit model) ?

It works.

Before my box fried I was using the ROM on the 100Mb model and it worked rather well and most definitely better than stock.