The damned "Romcode/Initialize DDR/Read initialize status/USB Control setup error" at 2%

[elparadise]

I read many messages about this error appearing during the USB firmware flashing. I have same problem with an MXQ Android BOX based on S805 Amlogic chip. After many tries, with two different PC's, two different cables and many types of firmware files finally i found the truth. I used the serial interface that is accessible on the PCB and i read the messages outputed during boot. This is the result:

QA5:A;SVN:B72;POC:3FF;STS:0;BOOT:0;INIT:0;READ:0;CHECK:0;PASS:0;
no sdio debug board detected
TE : 24850
BT : 16:59:29 Sep 21 2015
PMU:NONE
##### VDDEE voltage = 0x044c

CPU clock is 792MHz

DDR mode: 16 bit mode lane0+1
DDR size: 1GB (auto)
Stage 0 : 1

DDR test failed! Reset...
QA5:A;SVN:B72;POC:3FF;STS:6B730001;SKIP:0;BOOT:1;INIT:10;USB:3;

Have you seen? DDR test failed! Reset...

So, in my opinion, there is no possibility to update firmware because boot code refuses to continue proces, due to DDR failure. In fact may be that many of these box mount poor quality memory.

[dude0316]

what i do is uncheck the erase bootloader and it works idk why lol

[Centoori]

hello not working for me too... if any one can help...

[21:28:05 017][Global][Inf]--Scan USB host controller complete
[21:28:05 017][Global][Inf]--Update data center with HubMap
[21:28:05 017][Global][Inf]--Update hub3 device data
[21:28:05 017][Global][Inf]--Update HUB3-1
[21:28:05 017][HUB3-1][Inf]--Update device path
[21:28:05 017][Global][Inf]--Update HUB3-2 \\?\usb#vid_1b8e&pid_c003#5&105948fe&0&2#{a5dcbf10-6530-11d2-901f-00c04fb951ed}
[21:28:05 017][HUB3-2][Inf]--Update device path
[21:28:05 017][Global][Inf]--Update HUB3-3
[21:28:05 017][HUB3-3][Inf]--Update device path
[21:28:05 017][Global][Inf]--Update HUB3-4
[21:28:05 017][HUB3-4][Inf]--Update device path
[21:28:05 017][Global][Inf]--Update HUB3-5
[21:28:05 017][HUB3-5][Inf]--Update device path
[21:28:05 127][HUB3-2][Err]--[21:28:05 127][HUB3-2][Inf]--Failure : 2, FailureMax : 3
[21:28:05 642][HUB3-2][Err]--usb_get_configuration ret=-5 error_msg=sending get cached configuration ioctl failed, win error: Un périphérique qui n’existe pas a été spécifié.


[21:28:05 642][HUB3-2][Inf]--Failure : 3, FailureMax : 3
[21:28:06 248][HUB3-2][Err]--[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error
[21:28:06 248][HUB3-2][Inf]--Close device handle 0x00000850
[21:28:09 340][Global][War]--User click stop button
[21:28:09 340][Global][Inf]--Enable burning 0

FUC**G ERRoR

[FLAVIO98]

[0x10105002]Romcode/Initialize DDR/Read initialize status/USB Control setup error

como resolver isso?

[raruba]

Yeah I'm getting the same thing.....have tried everything can't get by 1% download DDR