M8S PRO W 2G 16G DD3 2018 11 21 rev 2.3 completely bricked

[KernelPanic]

At the end I bricked the M8S PRO @ completely.

The only thing that works is USB Burning tool, but I cannot find a suitable firmware to bring the unit back to life. The update process hangs at 4% with [0x10303004]Romcode/Switch status/Identify/Error result

This is the uart output

BL2 Built : 19:04:28, May 29 2018. \ngxl g034b32c-dirty - xianjun.liu@droid09-sz

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 6
CPU clk: 1200MHz
BL2 USB
Load fip header from USB, src: 0x0000c000, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from USB, src: 0x00010000, des: 0x01100000, size: 0x0000d600
Load bl31 from USB, src: 0x00020000, des: 0x05100000, size: 0x0002c600
Load bl32 from USB, src: 0x00050000, des: 0x05300000, size: 0x00036200
Load bl33 from USB, src: 0x00088000, des: 0x01000000, size: 0x00067600
NOTICE: BL3-1: v1.0(release):35dd647
NOTICE: BL3-1: Built : 15:20:30, Feb 7 2018
[BL31]: GXL CPU setup!
NOTICE: BL31: BL33 decompress pass
mpu_config_enablek
[Image: gxl_v1.1.3243-377db0f 2017-09-07 11:28:58 qiufang.dai@droid07]
OPS=0xc4
Wrong chip c0
GXL:BL1:9ac50e:bb16dc;FEAT:ADFC318C:0;POC:3;RCY:0; EMMC:800;NAND:82;SD:0;READ:0;CHK:A7;USB:8;


Thank you in advance

[JaV1]

Spanish:
Yo estoy como tu compa?ero.
he probado ya todo lo posible, pero no tengo la soluci?n.
?Has encontrado algo?

English:
I'm in the same situation than you
I have already tried everything possible, but I do not have the solution. Have you found something?

Gracias/Thank You

[Mitrix]

Hey KernelPanic

I have the same box, and you can Relive your Box with this Firmware from Lunn
mega.nz/#!Gd0kmYwI!D7NnwSeABK46sWZ-w9Tz4G_GwsdnRBh05ffNSPiOyjs

Flash this Firmware with Amlogic USB Burning tool and get over 4%

The problem with this box is, she Build from VideoStrong and not from Mecool
and that Board is over Nov 2018, all other Boxes have a board under Nov 2018 with the some Chipset (2.2 usw.....)

Sry for my English is a little bit bad^^

Hope this Help You

[Mitrix]

I have not found the Original Stock Firmware,
and the Firmware i have posted is from this Boxes build in Russia
GI Lunn 18, GI Lunn 28, GI Lunn 216

is identical with M8s pro W 2.3 2gb ddr3 16gb flash (Videostrong)

And this Board is not a p281, it?s similar a p212 Board

[JaV1]

Hey KernelPanic

I have the same box, and you can Relive your Box with this Firmware from Lunn
mega.nz/#!Gd0kmYwI!D7NnwSeABK46sWZ-w9Tz4G_GwsdnRBh05ffNSPiOyjs

Flash this Firmware with Amlogic USB Burning tool and get over 4%

The problem with this box is, she Build from VideoStrong and not from Mecool
and that Board is over Nov 2018, all other Boxes have a board under Nov 2018 with the some Chipset (2.2 usw.....)

Sry for my English is a little bit bad^^

Hope this Help You

WOW!!!!!!! YES!!!!!!!!

Thank you!!! At last I was able to restore the device. Seriously, I owe you a good beer !! I shearch now a Mecool firmware ZIP!!! Thank you again!!

[KernelPanic]

I will try and let you know. Thanks for now

[KernelPanic]

The update stops at 7% with the firmware from Lunn.
Still bricked

[JaV1]

The update stops at 7% with the firmware from Lunn.
Still bricked

change temperature setting or try "short mode"

[nikito7989]

Lunn-NHG47L-20190418.114957.V0213.img
https://drive.google.com/file/d/1X28...lMVddAtoI/view

[nikito7989]

M8S_PRO_W-OTA-ATV-20180802.182556.V0213.zip
https://drive.google.com/file/d/1kM_-zv0XcKLNv83TbHlbUqp4AoY6Eg6v/view

[JaV1]

I programed a new Version for LUUN and Update to recovery my M8s V2.3...

You need with Usb Loader 2.08 and put this image on Short mode ( you can see the image )

https://mega.nz/#!SdxXXAbC!ob80ieq0VCGtpcsQOVeC-pdSOpI73fMPvkSTCTWJ_ig

later you put this update into a USB and update from zip

https://mega.nz/#!7NhRkQgL!3CwLUxflT7k492ejC7jjinA10c7U2Cxk2EzQbMSPt60

[felipevmacedo]

Thanks to you i can unbrick my box. Thank you, for real.
I had just one question, what is the correct Nexus firmware for this box version? I tried before by OTA and bricked.

[nikito7989]

Thanks to you i can unbrick my box. Thank you, for real.
I had just one question, what is the correct Nexus firmware for this box version? I tried before by OTA and bricked.

https://drive.google.com/file/d/15SBxghA1lu7kQkvns_pf_ZVl1fZT-XKG/view

[felipevmacedo]

https://drive.google.com/file/d/15SB...l1fZT-XKG/view

I bought the box with Voice Control, but doesn't work. The voice control will work with my remote control after install this firmware?

[nikito7989]

I bought the box with Voice Control, but doesn't work. The voice control will work with my remote control after install this firmware?

I bought the box with Voice Control
Nexus ATV Voice Control firmware https://drive.google.com/file/d/15SB...l1fZT-XKG/view

This just seems to be a burn packaged built from raw partition images of my M8S_PRO_W-V0213_TVStock-20190216 release. You're probably better off downloading the original, which is about half the size.