Announcement

**CcX85** · 19 April 2019, 22:23

Hi there, thanks for bringing us yet another updated Poison TV bring life to old box all around the world (UK here)

Can I ask when you say 1gb version or regular is that the total Ram or what is available?

example the Probox2 Air using CPU-Z say Total Ram = 1808MB and Available Ram is 903mb

hope you can work make sense of that!

Cheers

**minixfreak** · 19 April 2019, 22:37

Originally posted by CcX85 View Post

Hi there, thanks for bringing us yet another updated Poison TV bring life to old box all around the world (UK here)

Can I ask when you say 1gb version or regular is that the total Ram or what is available?

example the Probox2 Air using CPU-Z say Total Ram = 1808MB and Available Ram is 903mb

hope you can work make sense of that!

Cheers

Total ram so if it's 2gb of ram then use regular one

**CcX85** · 19 April 2019, 22:55

Thanks for that, I went with the regular one base on that logic too.

I've installed it to the Probox2 Air that was last updated in 2016 and so far so good keep you informed.

Tip - Connect usb to ur pc/laptop, then usb male goes in the usb slot near the TF card
but hold the reset pin while slotting the usb cable into the box and ur see it connected on usb burning tool.

**hannah** · 20 April 2019, 20:12

See my post here:

https://forum.xda-developers.com/showpost.php?p=79374256&postcount=53

Fully working in NEXBOX Model: A95X (2G+16G, S905X)
Wifi and Play Store do not work in CooleMe CM-MM1 (it is a clone of Mecool M8s pro W)

**tombraga** · 23 April 2019, 08:17

I have the box M8S Plus W, so i have to use the PoisonATV_V4.9_S905W.img right? (not the nexbox img)

and where i can get the USB Burningtool 2.1.7?

**hannah** · 23 April 2019, 08:30

Originally posted by tombraga View Post

I have the box M8S Plus W, so i have to use the PoisonATV_V4.9_S905W.img right? (not the nexbox img)

and where i can get the USB Burningtool 2.1.7?

USB Burning Tool v2.16 for Amlogic Processors Released - FreakTab

https://forum.freaktab.com/forum/tv-player-support/allwinner-tv-players/freaktab-tools-utulities-collection/723143-usb-burning-tool-v2-16-for-amlogic-processors-released

The executable will install the drivers and the utility itself. There’s also a changelog in Chinese. The Google Translation of the changelog may be useful to find

**tombraga** · 23 April 2019, 10:30

Originally posted by hannah View Post

https://forum.freaktab.com/forum/tv-...ssors-released

thanks, but this is 2.1.6 and in the installation infos of minixfreak in the 1. post he speaks about 2.1.7 to use for flashing

installed now with 2.1.6 without any issues, now i will test the rom, thanks

**tombraga** · 23 April 2019, 22:47

I installed now the PoisonATV_V4.9_S905W.img on my androidTV M8S Plus W - but i cannot activate my wifi in the settings, during the first installation did not find any wifi, but my other box Mecool M8S Pro L and my tablets, all find the wifi connections.

when i try to switch on the wifi in network settings, it switch off automatically.

Before i had the original firmware installed and wifi was working.

what can i do ??

**jae** · 23 April 2019, 23:03

I'm cant seem to get USB burning tool to recognize the Nexbox A95X.

It's new, never been booted... I installed the USB burning tool 2.1.6 from above post, started it, plugged in the USB cable to port furthest from the micro sd card slot.
I hear the Windows sound that USB is connected, Burning Tool says USB Hub connected, but after a short time (Windows 7 can't find drivers I think), I hear the sound of the USB device being disconnected.

Pressing Start does nothing.

Don't know what to do.

I haven't rebooted since installing Burning Tool. Maybe I have to do that to get the drivers to be recognized as available. ?

**minixfreak** · 23 April 2019, 23:35

Originally posted by tombraga View Post

I installed now the PoisonATV_V4.9_S905W.img on my androidTV M8S Plus W - but i cannot activate my wifi in the settings, during the first installation did not find any wifi, but my other box Mecool M8S Pro L and my tablets, all find the wifi connections.

when i try to switch on the wifi in network settings, it switch off automatically.

Before i had the original firmware installed and wifi was working.

what can i do ??

U have a wifi that's different from what's supported

**legnosecco** · 23 April 2019, 23:47

Originally posted by jae View Post

I'm cant seem to get USB burning tool to recognize the Nexbox A95X.

It's new, never been booted... I installed the USB burning tool 2.1.6

USB burn tool 2.1.6 would not work for me on Windows 7 - I'm using ver 2.0.8

Open the burn tool...then connect USB cable with your TV box to the PC usb port

After you get the connected message in the tool window, import your image file.

Make sure only Erase Flash (Force Erase) and Erase bootloader are ticked.

Now press the START.... it will start but then fails with an error...and usb connection is lost.

Pull out the USB cable only from the PC usb port... wait 5 seconds.... plug in USB cable back in the PC usb port.

Do nothing....It will re-connect automatically and the burn process will start.

Wait until finished and you see the SUCCESS message....then you can pull out the USB cable from the PC usb port and close the tool window.

This is how it works for me every time.

**tombraga** · 24 April 2019, 00:02

Originally posted by minixfreak View Post

U have a wifi that's different from what's supported

and now? nothing to do? this box dont have ethernet port, only works with wifi

the worst, i lost my original firmware or other rom which i could install on it...I believed what this rom promissed, for ALL S905W boxes...

**jae** · 24 April 2019, 00:30

Originally posted by legnosecco View Post

USB burn tool 2.1.6 would not work for me on Windows 7 - I'm using ver 2.0.8

Open the burn tool...then connect USB cable with your TV box to the PC usb port

After you get the connected message in the tool window, import your image file.

Make sure only Erase Flash (Force Erase) and Erase bootloader are ticked.

Now press the START.... it will start but then fails with an error...and usb connection is lost.

Pull out the USB cable only from the PC usb port... wait 5 seconds.... plug in USB cable back in the PC usb port.

Do nothing....It will re-connect automatically and the burn process will start.

Wait until finished and you see the SUCCESS message....then you can pull out the USB cable from the PC usb port and close the tool window.

This is how it works for me every time.

Thanks. Will try.

Have a link for 2.0.8?

*found one on chinagadgetreview
Will give it a go.

Eh. The 2.0.8 I found is in Chinese, I can't read a damned thing. But it looks like it's doing the same thing as the 2.16 was doing... It says connected to the Hub and then the Windows beep for USB disconnecting some moment\s later

Gonna try with 2.1.6.8 I found on CGR also.

**jae** · 24 April 2019, 02:41

@legnosecco
I've tried on 2.1.6, and 2.0.8 (my posts are getting held)

I see "Hub-2" in the top half of the window.. Nothing for Status, Time, or Statistic

Nothing in the bottom half

Tried pressing Start..

No changes.. Waited 10 minutes. Nothing

Tried it on two Win 7 laptops.

I have no idea wtf is wrong

Announcement

Announcement

{ROM} PoisonATV V4.9 S905X

{ROM} PoisonATV V4.9 S905X

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

What's Going On