S905x Abox

[agarest]

Good morning,
a few days ago I recovered an ABOX with S905x on which I managed to run Debian via SD card.

All good until I decided to install Debian on the Nand with the "nand-sata-install" command that I found while surfing the internet. From that moment it no longer works, the red LED stays on steadily (normally it lit blue at start-up) and on the monitor I only see the word "ABOX" which remains there for hours without doing anything.

I took out the UART and with a USB converter and Putty I can see some instructions but I don't know what to do.

How can I proceed to permanently install Debian on this card? Thank you very much!

[agarest]

D:0;0.0;CHK:0;
TE: 55413

BL2 Built : 11:58:42, May 27 2017.
gxl gc3c9a84 - xiaobo.gu@droid05

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 2
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - PASS
Rank0: 1024MB(auto)-2T-13
Rank1: 1024MB(auto)-2T-13
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x05100000, size: 0x00018400
Load bl33 from eMMC, src: 0x0003c200, des: 0x01000000, size: 0x000a9c00
NOTICE: BL3-1: v1.0(release):3348978
NOTICE: BL3-1: Built : 15:44:01, May 12 2017
[BL31]: GXL CPU setup!
mpu_config_enable:ok
[Image: gxl_v1.1.3221-2cfba69 2017-05-27 16:03:58 qiufang.dai@droid07]
OPS=0x82
31 e7 64 73 b4 ec 47 ed 3 bd ae fd [0.302131 Inits done]
secure task start!
high task start!
low task start!
ERROR: Error initializing runtime service opteed_fast


U-Boot 2022.01-armbian (Mar 25 2022 - 22:24:15 +0800) libretech-cc

Model: Libre Computer AML-S905X-CC
SoC: Amlogic Meson GXL (S905X) Revision 21:b (82:2)
DRAM: 2 GiB
MMC: mmc@72000: 0, mmc@74000: 1
Loading Environment from nowhere... OK
In: serial
Out: serial
Err: serial
[BL31]: tee size: 0
[BL31]: tee size: 0
Net: eth0: ethernet@c9410000
Hit any key to stop autoboot: 0
Card did not respond to voltage select! : -110
switch to partitions #0, OK
mmc1(part 0) is current device
Scanning mmc 1:1...
Found U-Boot script /boot/boot.scr
1123 bytes read in 1 ms (1.1 MiB/s)
## Executing script at 08000000
Start AMLOGIC mainline U-boot
## Error: "bootfromsd" not defined
Couldn't find partition usb 0
Couldn't find partition usb 1
Couldn't find partition usb 2
Couldn't find partition usb 3
SCRIPT FAILED: continuing...
libfdt fdt_check_header(): FDT_ERR_BADMAGIC
Card did not respond to voltage select! : -110
Scanning disk [email protected]...
Disk [email protected] not ready
Scanning disk [email protected]...
Found 2 disks
No EFI system partition
BootOrder not defined
EFI boot manager: Cannot load any image
MMC Device 2 not found
no mmc device at slot 2
starting USB...
Bus usb@c9000000: dwc3_meson_gxl_get_phys: usb2 ports: 2
Register 2000140 NbrPorts 2
Starting the controller
USB XHCI 1.00
scanning bus usb@c9000000 for devices... 1 USB Device(s) found
scanning usb for storage devices... 0 Storage Device(s) found

Device 0: unknown device
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.221.184 (9 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
missing environment variable: pxeuuid
Retrieving file: pxelinux.cfg/01-16-ae-93-6b-a1-d5
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A8DDB8
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A8DDB
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A8DD
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A8D
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A8
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0A
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C0
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/C
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm-meson-p212
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm-meson
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default-arm
Speed: 100, full duplex
*** ERROR: `serverip' not set
Retrieving file: pxelinux.cfg/default
Speed: 100, full duplex
*** ERROR: `serverip' not set
Config file not found
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.221.184 (10 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET
Speed: 100, full duplex
BOOTP broadcast 1
DHCP client bound to address 192.168.221.184 (4 ms)
*** ERROR: `serverip' not set
Cannot autoload with TFTPGET

[brain42]

I have the same box, and havent had much luck using the toothpick method or otherwise. Can you post how you got this to work and link to image used?