remote.conf for square remote (v1 m8)

[fr0stxm]

Afternoon,

As the title suggests, does anyone have the remote.conf for the square remote that comes with the v1 m8 square units?

tyvm

Finally signed up with an account, always lurking; never posting

[danyway]

Hi

I have it.

You can save the text bellow in a remote.conf text file :

#************************************************* ************************************************** ******
#this file is configuration for each factory remote device
# work_mode 0 :software mode 1 :hardware mode
# repeat_enable 0 :disable repeat 1 :enable repeat
#
# factory_code each device has it's unique factory code.
# pattern:custom_code(16bit)+index_code(16bit)
# examble: 0xff000001 = 0xff00(custom cod) 0001 (index)
#
# release_delay unit:ms.release will report from kernel to user layer after this period of time
# from press or repeat triggered.
#
# debug_enable 0 :debug disable 1 :debug disable
#
# SW MODE:
# bit_count how many bits in each frame
# tw_leader_act time window for leader active
# tw_bit0 time window for bit0 time.
# tw_bit1 time window for bit1 time
# tw_repeat_leader time window for repeat leader
# REG
# reg_base_gen set value for PREG_IR_DEC_BASE_GEN
# reg_control set value for PREG_IR_DEC_CONTROL
# reg_leader_act set value for PREG_IR_DEC_LEADER_ACTIVE
# reg_leader_idle set value for PREG_IR_DEC_LEADER_IDLE
# reg_repeat_leader set value for PREG_IR_DEC_REPEAT_IDLE
# reg_bit0_time set value for PREG_IR_DEC_BIT0_TIME
#************************************************* ************************************************** **********
#amlogic NEC remote
factory_code = 0xfe010001
work_mode = 0
repeat_enable = 1
repeat_delay = 40
repeat_peroid = 39
release_delay = 121
debug_enable = 1


fn_key_scancode = 0x00
left_key_scancode = 0x51
right_key_scancode = 0x50
up_key_scancode = 0x16
down_key_scancode = 0x1a
ok_key_scancode = 0x13
pageup_key_scancode = 0x55
pagedown_key_scancode = 0x54


mouse_begin
0 0x51
1 0x50
2 0x16
3 0x1a
mouse_end


key_begin
0x01 11
0x4e 2
0x0d 3
0x0c 4
0x4a 5
0x09 6
0x08 7
0x46 8
0x05 9
0x04 10
0x13 97
0x19 15
0x42 14
0x16 103
0x1a 108
0x51 105
0x50 106
0x11 104
0x18 102
0x10 125
0x4c 109
0x5a 119
0x59 122
0x52 128
0x58 123
0x54 120
0x55 121
0x40 116
0x41 113
0x45 130
0x49 134
0x0a 133
0x48 138
0x4d 70
0x0e 136
0x0f 135
0x43 132
0x03 127
0x06 139
0x44 140
0x00 63
key_end
repeat_key_begin
0x01 11
0x4e 2
0x0d 3
0x0c 4
0x4a 5
0x09 6
0x08 7
0x46 8
0x05 9
0x04 10
0x13 97
0x19 15
0x42 14
0x16 103
0x1a 108
0x51 105
0x50 106
0x11 104
0x18 102
0x10 125
0x4c 109
0x5a 119
0x59 122
0x52 128
0x58 123
0x54 120
0x55 121
0x40 116
0x41 113
0x45 130
0x49 134
0x0a 133
0x48 138
0x4d 70
0x0e 136
0x0f 135
0x43 132
0x03 127
0x06 139
0x44 140
0x00 63


repeat_key_end

[alon24]

How do I use this file?
where to place?
How to make sure it is read?