If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
Changing some BIOS setting and bricking the device is a very common situation in Teclast X98 tablet, and it is actually quite easy to resolve this situation by reprogramming the BIOS with a very cheap external programmer.
The problem with PiPo X7 may be exactly the same. You just have to wait until Frontier gets the programmer to reprogram the BIOS chip.
In that case, it can even be possible to try to change every available BIOS setting one by one, to find out which setting causes the problem and create a NOT TO DO list.
Teclast X98 Air 3G Tablet: 9.7" 2048x1536 px - Z3736F - 3G - Android/Windows 8.1
Hi to everyone,
I would like to apologize because my english is not so good.
This thread could be usefull for to get informations and modding istructions about the...
Since there are many users having this issue, can you describe step by step what exact procedure you did follow to solve this issue?
What exactly do you mean by removing and re-installing the main PCB without unplugging the cables? Just removing the screws of the large PCB and detach it from the case?
Yes, just removing the screws from the large PCB and detach it from the case.
That does not seem logical at all, unless touching some components with bare hands had something to do with resetting.
Anyway, since you claim that the procedure is reproducible, please describe it thoroughly.
Yes, it is not logical. The plastics seems to be metallised. Maybe I shorted something
I expect to have the programmer by the end of this week (if weather conditions permit).
In the meantime, you can download the necessary software from here (password for CH341 programmer: ch314).
The repository contains EEPROM programming software for both CH341 (the cheap one) and SP300U (the expensive one) kits.
Cables and CH341A programmer arrived today from Larissa; after trying for over 4 hours, I give up! I cannot make the programmer detect the chip (Winbond W25Q64DW, the software goes up to W25Q64BV) therefor I cannot re-flash the X7.
I am THAT close of throwing the whole thing to the recycle bin, so frustrated.
And all that because of one BIOS option change and for PiPO not providing a simple BIOS restore or reset function.
If you plan to use the X7 for anything other than running Windows 8.1, AVOID it.
It's not worth the trouble.
Thanks but these are useless; they are just instructions and files to re-install Windows 8.1 and a BIOS update. They cannot be used with devices that have bricked BIOS.
Cables and CH341A programmer arrived today from Larissa; after trying for over 4 hours, I give up! I cannot make the programmer detect the chip (Winbond W25Q64DW, the software goes up to W25Q64BV) therefor I cannot re-flash the X7.
I am THAT close of throwing the whole thing to the recycle bin, so frustrated.
And all that because of one BIOS option change and for PiPO not providing a simple BIOS restore or reset function.
If you plan to use the X7 for anything other than running Windows 8.1, AVOID it.
It's not worth the trouble.
After looking at mine, I think the issue is probably that the chip is a leadless surface mount package. I assume you're using a standard test clip which is designed to contact the edge of the chip. If you look closely, that chip doesn't have legs coming out the sides for the clip to touch. I haven't been able to find an adapter that will work with that chip but this is all new to me. Also, the data sheet it needs 1.8 volts. Be sure your programmer can do that rather than 5v or 3.3v.
I wonder how difficult it would be to remove the existing chip and put in a normal package with legs or, better yet, a socket. I'm not sure if my soldering skills are good enough for something that small.
Yea without having legs on the chip soic clips are no good. If you have the skills / tools needed it would probably be easier to just buy a replacement bios chip from **** and re-solder that one back on
After looking at mine, I think the issue is probably that the chip is a leadless surface mount package. I assume you're using a standard test clip which is designed to contact the edge of the chip. If you look closely, that chip doesn't have legs coming out the sides for the clip to touch. I haven't been able to find an adapter that will work with that chip but this is all new to me. Also, the data sheet it needs 1.8 volts. Be sure your programmer can do that rather than 5v or 3.3v.
I have isolated the GND and VCC pins from the CH341A programmer (VCC is 3.3V) and instead I am using the VCC and GND ports from a Mixtile Garage Exynos 4412 board, which provides 1.8V. You could be right about the SOIC package used; there are legs but they are completely flat and it could be that the adapter pins do not even make contact with them.
I could try desoldering the chip and put it on a help socket board the programmer has but I am not THAT skilled...
Yea without having legs on the chip soic clips are no good. If you have the skills / tools needed it would probably be easier to just buy a replacement bios chip from **** and re-solder that one back on
Will a simple hot air gun do the job of re-soldering it?
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment