Rockchip Create Upgrade Disk Tool v1.4 helps you to install firmware on Rockchip device from Micro SD card

[budgetgeek]

The program does not recognize my sd card help

Run as an administrator.

[scooter2014]

I think i finally killed my tester mk902ii it fails to boot. I can get into recovery but the first update fails halfway through. I am able to flash back to stock kk but when i upgrade to anything but wasser .2 i get no sound its driving me crazy lmao. But sound works in kk. Think ill keep playing.

[budgetgeek]

I think i finally killed my tester mk902ii it fails to boot. I can get into recovery but the first update fails halfway through. I am able to flash back to stock kk but when i upgrade to anything but wasser .2 i get no sound its driving me crazy lmao. But sound works in kk. Think ill keep playing.

Didn't you flash the sdcard on it once by mistake? Do you think that would work again?

[scooter2014]

One time more like 100 lmao... Anyways back on stock 4.4 if i flash anything else no sound. I re flashed and bricked it to get nack to mask mode. It flashed both update and update1 but did not re boot into any firmware. Hooked back up to pc mask mode again. Ill try neo modes atv once he posts update.

[moose m79]

After bad cwm update decision on 802 mkiiis with sandisk band I tried short pins 7-8/8-9 etc when I should have done 5-6 now nowww HDMI ROM mask mode does come up in tool but flash fails at first restart unless I only flash loader. How can I use this this this tool withooout HDMI?

[kurocygnus]

I'm trying to use this to change the firmware on my MXQ 4K (which came with 6.0.1). I flashed the rom to the SD card (a sandisk ultra 8gb) but the MXQ only boots normally and ignores the SD card. I tried another SD card (a 4GB one that came with my Nintendo 3DS) but at the end of the flash it fails without any explanation. I'm trying to flash the rom from this topic http://freaktab.com/forum/tv-player-...erceleron-v1-0
What i'm doing wrong?

[gefattern]

Hi kurocygnus ,

are you sure it works with your SoC RK3229 Device , is it not only for RK3288 ???

I dont know , u must use Stockrom no CustomRom from Superceleron . I believe .

good luck

gefattern

[kurocygnus]

Hi kurocygnus ,

are you sure it works with your SoC RK3229 Device , is it not only for RK3288 ???

I dont know , u must use Stockrom no CustomRom from Superceleron . I believe .

good luck

gefattern

The CustomRom from Superceleron was made for the 3229, I believe. Doesn't matter now, I bricked my MXQ-4K because I'm dumb. I used the RKBatchTool and pressed the wrong button (Restore) and now my box is in Maskrom mode...

[gefattern]

The CustomRom from Superceleron was made for the 3229, I believe. Doesn't matter now, I bricked my MXQ-4K because I'm dumb. I used the RKBatchTool and pressed the wrong button (Restore) and now my box is in Maskrom mode...

Hi again ,

Restore or Upgrade no difference , flash must work , if your Box is in MRM you can flash

it easily again with a new Rom , best StockRom first , then any you want , if compatible .

good luck , report

gefattern

[kurocygnus]

Hi again ,

Restore or Upgrade no difference , flash must work , if your Box is in MRM you can flash

it easily again with a new Rom , best StockRom first , then any you want , if compatible .

good luck , report

gefattern

I tried to flash it in MRM, but it gives me a Test Device Failed... I think that's because my usb cable (which I made...) is not writing anything... I'll try a new cable tomorrow.

[EagleEyeXZ]

when i use "create" the program closes trying to make a MBR on Windows 10

[Babb1]

when i use "create" the program closes trying to make a MBR on Windows 10

It is the same for me. The same on Windows 7. I have tried Windows 10 64 bit and Windows 7 32 bit as well.
My chip is RK3399

How can I use this tool?

[gefattern]

It is the same for me. The same on Windows 7. I have tried Windows 10 64 bit and Windows 7 32 bit as well.
My chip is RK3399

How can I use this tool?

Hi did you download the Version 1.43 from the first Page (Post12) ???

This version worked for me on Win7 , like Renixo discribed , but my Box

did not "boot" with it into Recovery , first 2sec Blackscreen then "no Input"

on Tv , like always before , since it bricked , hope i can get it back to Life .

good luck / gefattern

[Babb1]

Yes, I used Version 1.43.
no success...

[gefattern]

Yes, I used Version 1.43.
no success...

Hi ,

how did you use it , like "Renxio" discribed , both checked ??? ,

but what is your Problem with your Box , can it not be restored

by Flashtool and Stockrom ??? "Maskrommode"

greetings / gefattern