Mk809 II instructions doesn't match..

[dk-wamp]

Hello, I have a problem with flash of mk809 II.

When I launch 'Reboot to flash mode' my device doesn't reboot,
The instructions are:

6) Now in the ug802 advanced settings go to the "device" area (the TV tube icon).
7) In there change the "USB Computer Connection" to "Mass Storage". Windows will BONG it found a device.
Note: If it was already set to that, change it to "Media Device (MTP)".  
Windows will BONG again it found a device and NOW again switch it back to Mass Storage.  
The point is we need that change in state at least once!!!
Also make sure in advanced settings the USB Debugging is turned off!

9) Once it says "Found RKAndroid Mass Storage Usb" in the flash tool click the "Reboot to Flash Mode" button.
10) Wait up to at least 10 seconds.  The unit should reboot and the screen for the ug802 will be black (no ouptut).
11) If the unit does not reboot to a blank screen, repeats steps 7-9.
Congrats!  You are now in flash mode!  To get out of it at any time just unplug the USB power to the ug802.
It will boot back up normally out of flash mode.

The problem is in number 6/7 I haven't this option. (look the picture)
in setting Usb i have only 'connect to pc'
(dubuggin is off and I see Found RKAndroid Mass Storage Usb)



Can you help me please?

Ps
I tried with 1.7 and 1.8 my device is new without mod and on my pc i see mk809 II like a Usb storage (ROCKCHIPS)

[Abducted]

I cant remember for sure, but i think you can either change it under "storage" or under that USB tab and it should be all the in the upper right corner.

[dk-wamp]

there isn't anything in the righ corner or storage



do you know others methods to become root?

[dk-wamp]

oh damn!! I found now, is in storage, but is like a picture is not icon..


but now other problem, when I switch from 'mass storage' to mpt flashtool change message from 'found' to 'not found'.

omg... I can't install seven driver on rk30sdk, it work with system drivers, whitout system drivers don't work and don't accept drivers/x64/win7/ drivers, I tried with vista laptop and the same problems (drivers/x86/vista/

[Abducted]

Did you force the drivers manually? The "have disk" way (not sure why they still call it that, quite sure there is a whole generation who has never seen a (floppy) disk. )

[ididmytime]

I am using win7 x64.

I can tell you right now, the Finless Rom Flash Tool cannot reboot to flash mode with my setup.

Uninstall all the drivers you have, connect the stick to the PC, make sure debugging is off and select 'Connect to PC'. When you see the device in Windows (will look like a hard drive, make sure it's in mass storage mode) Use the RKBatchTool, and press switch.

[dk-wamp]

Did you force the drivers manually? The "have disk" way (not sure why they still call it that, quite sure there is a whole generation who has never seen a (floppy) disk. )

Sure, but my win 7 64 ultimate don't accept this driver

[dk-wamp]

I am using win7 x64.

I can tell you right now, the Finless Rom Flash Tool cannot reboot to flash mode with my setup.

Uninstall all the drivers you have, connect the stick to the PC, make sure debugging is off and select 'Connect to PC'. When you see the device in Windows (will look like a hard drive, make sure it's in mass storage mode) Use the RKBatchTool, and press switch.

Done.. but is the same, doesn't reboot
" switch done success 1 fail 0" and the numer 1 now is green.
I tried to reboot manually but nothing...

[ididmytime]

Done.. but is the same, doesn't reboot
" switch done success 1 fail 0" and the numer 1 now is green.
I tried to reboot manually but nothing...

It's supposed to. When the number 1 is green that means it's worked, hence why it says success 1 fail 0.

You can then press flash rom in the finless rom tool and it will flash the rom.

[dk-wamp]

It's supposed to. When the number 1 is green that means it's worked, hence why it says success 1 fail 0.

You can then press flash rom in the finless rom tool and it will flash the rom.

done, thank you very much! :=)

[Abducted]

Nice one ididmytime!

[dk-wamp]

deleted this post please

[Coellophysis]

Want to flash my mk809 iii but no connections with Windows 7

Hello I was following a tuto for flashing my rom but I have a stupid issue on the fact that my Win 7 do not recognise the mk809 (I put the micro USB on the side, I connected the HDMI), I tried with my own cable micro usb from my smartphone android that supposed to work fine.

In "system" I cannot see the yellow "?" that says that it has an USB mass ot unrecognize. So how can I solve this problem?

Thanks

[blinkone]

Hello I was following a tuto for flashing my rom but I have a stupid issue on the fact that my Win 7 do not recognise the mk809 (I put the micro USB on the side, I connected the HDMI), I tried with my own cable micro usb from my smartphone android that supposed to work fine.

In "system" I cannot see the yellow "?" that says that it has an USB mass ot unrecognize. So how can I solve this problem?

Thanks

Your drivers are not installed correct on your pc, I had no problem on my windows7 but evey pc is different try this tool http://blog.geekbuying.com/index.php...download-here/

[Coellophysis]

Want to flash my mk809 iii but no connections with Windows 7

Your drivers are not installed correct on your pc, I had no problem on my windows7 but evey pc is different try this tool http://blog.geekbuying.com/index.php...download-here/

Hello blinkone,

Thank you for your answer, I loadedte RK rive assistant but it still fails ? What I supposed to do once I installed the tool, nothing particular right? The device shoulde recognized by Windows?

OK guys, I found the solution, I missed the step where I've to put the paper clip before plugging the micro-USB

Best regards