Mini MXIII Stock Firmware

[EGM92]

I updated to the wrong firmware, I used Amlogic burn to burn a .img file for the mini mx instead of the mini mxiii, is there any way to flash this. I attempted to load it through the OTA back/restore app but it always fails with a (Status 1) error. Would you have any advice or a solution on how to get back to the factory image for the mxiii without a .img ?

Thanks.

[gap300789]

I updated to the wrong firmware, I used Amlogic burn to burn a .img file for the mini mx instead of the mini mxiii, is there any way to flash this. I attempted to load it through the OTA back/restore app but it always fails with a (Status 1) error. Would you have any advice or a solution on how to get back to the factory image for the mxiii without a .img ?

Thanks.

http://freaktab.com/forum/tv-player-support/amlogic-based-tv-players/s905/beelink-ac/578806-mini-mxiii-twrp-backup-of-stock-rom

[EGM92]

http://freaktab.com/forum/tv-player-...p-of-stock-rom

Thank you! Will this fix the lack of wifi when I flash the rom?

[gap300789]

Thank you! Will this fix the lack of wifi when I flash the rom?

Yes it will take back to stock settings

[cachepc]

OK, so I'vbre tried all methods to get TWRP and stock firmware onto my bootloop'ing Beelink MX III. Here's what I have tried to date:
1. OpenElec Image - tried both with and without holding down the reset switch with a paperclip
2. TWRP written to MicroSD which was FAT32 formatted -tried with and without holding down the reset switch with a paperclip

Basically, my MXIII ran perfectly ONCE using the Out of the Box software - didn't do anything to the box in terms of loading up new firmware, although I tried using the OTA updater. I didn't check that this may have been updating while I was doing other things but I would hope the process would be stable enough for that.

So, I need help to restore. The symptoms are that when I apply power, my HDMI monitor shows active on power but then shows no HDMI signal on the screen.

Do I need to use the AMLOGIC USB Burning tool to resurrect (which means I need a USB cable to do so ?) or do I just send it back to where I brought it ?

Any (dummy) instructions on how to fix would be greatful - I've done Samsung phones using ODIN and also MTK phones, so can generally get by with most things, but this looks dead......

[gap300789]

OK, so I'vbre tried all methods to get TWRP and stock firmware onto my bootloop'ing Beelink MX III. Here's what I have tried to date:
1. OpenElec Image - tried both with and without holding down the reset switch with a paperclip
2. TWRP written to MicroSD which was FAT32 formatted -tried with and without holding down the reset switch with a paperclip

Basically, my MXIII ran perfectly ONCE using the Out of the Box software - didn't do anything to the box in terms of loading up new firmware, although I tried using the OTA updater. I didn't check that this may have been updating while I was doing other things but I would hope the process would be stable enough for that.

So, I need help to restore. The symptoms are that when I apply power, my HDMI monitor shows active on power but then shows no HDMI signal on the screen.

Do I need to use the AMLOGIC USB Burning tool to resurrect (which means I need a USB cable to do so ?) or do I just send it back to where I brought it ?

Any (dummy) instructions on how to fix would be greatful - I've done Samsung phones using ODIN and also MTK phones, so can generally get by with most things, but this looks dead......

http://freaktab.com/forum/tv-player-support/amlogic-based-tv-players/s905/beelink-ac/578806-mini-mxiii-twrp-backup-of-stock-rom

Follow these instructions, use the toothpick method to boot your box into TWRP

[cachepc]

So, I tried the Samsung TV and it booted perfectly into BeeLink UI.... Dooohh.....

[EGM92]

This fixed my wrongful flash, thank you. Just a question maybe you could help me with I have an app from my cable provider that's not working because the mirroring app is installed. I've tried using titanium backup to remove the app but I still have blocks in the app. Is there any way to completely remove the mirroring app and its components in the rom?

[gap300789]

This fixed my wrongful flash, thank you. Just a question maybe you could help me with I have an app from my cable provider that's not working because the mirroring app is installed. I've tried using titanium backup to remove the app but I still have blocks in the app. Is there any way to completely remove the mirroring app and its components in the rom?

Just follow my other guide and do a fresh install of the TWRP backup

[w3r3w0lf]

Hello can you please check a firmware update to this box?
Since the launch of the box it has the same firmware that has some problems with sound playback in many apps.

Actual firmware 107L1_0425

Thanks
RS

[bluesmanuk]

Hello can you please check a firmware update to this box?
Since the launch of the box it has the same firmware that has some problems with sound playback in many apps.

Actual firmware 107L1_0425

Thanks
RS

You can find details about Beelinks own firmware and updates here

http://www.bee-link.com/Beelink-forum-64-1.html

Moving this to the stock firmware discussion thread.

[formingus]

MiniMXIII 107L1_0425 Firmware

https://mega.nz/#F!M9FxDJZY!Qyf61LTqgARUUaW9k2bB7A

Password: !Qyf61LTqgARUUaW9k2bB7A

Dude , you RE GENIOUS , you just brick mine TV Box. Cant understand those amatory why posting !!!