H96 Pro Plus short pin unbrick help

[blueprintdk]

Hi guys, finally I could repair the brick of my TVBox following your advice the problem was the USB cable that has to be like the one we used for data, so I built one that had at home with their respective splices and Windows 10, I detect perfectly, I already have another TVBox new thanks to the advice of this chat. Thank you, thank you.

Is the cable you made a crossover cable or do you connect + to + / ground to ground / data + to data+ and data - to data - ???

[Mischel68]

Hello

A few info about my box. Purchased in China. Supplied without function. Only the blue LED is permanently on. I had a loss of 10 Euro €. I do not know whether the box has a defective hardware. At the bottom of the board are 2 stickers. One with the MAC address 78: C2: C0 etc. The second sticker: CZ / 3G + 16G + 9377 JOB 20170117.
On the main side of the board: CZ-S32-V3 (DDR4) QL 1707
2xRAM 6NB77 D9TGG together 3GB
ROM Samsung 543A KLMA626EAC-B001 16GB
WIFI Fn-Link 8223A-SR F02021 1708

4x USB on board


I have tried a firmware. With USB Burnig Tool max. to 7%. With the SD Metode is nothing. The box does not boot from the SD card.

Great question now. What firmware should I still test.

Regards

[BR6]

Dont short the pins you dont need that just use stock rom and flash it as tooth pic method with the burn card stock rom and you'll be fine disconect the hdmi cable during.g the process

Sent from my SM-N9300 using Tapatalk

My situation is same, but I had a box with 20170905 build, then flashed superceleron over it (100%), no boot , no recovery or logos, question now is which is my stock rom? and will sdcard burn maker revive it.

[hcardoso483]

Hello

I have a bricked H96 Pro Plus. The led lights permanently with black picture. No signal on HDMI.

I have read the posts here. I do not know exactly what you do with the pins.
Do I need to solder wires there? Then switch to Ground? I have a Samsung NAND on the board. Which pins do I need with the Samsung chip. 3GB Ram 16 GB rom.

Until now I have tried with USB Burning Tool the unbrick. But I always have an error at 7%.
I also have questions about the tool. Do I need separate files for each firmware in the license folder?

I hope you can help me and I understand the approach.

Regards

Dont short the pins you dont need that just use stock rom and flash it as tooth pic method with the burn card stock rom and you'll be fine disconect the hdmi cable during.g the process

Sent from my SM-N9300 using Tapatalk

[Mischel68]

Hello

I have a bricked H96 Pro Plus. The led lights permanently with black picture. No signal on HDMI.

I have read the posts here. I do not know exactly what you do with the pins.
Do I need to solder wires there? Then switch to Ground? I have a Samsung NAND on the board. Which pins do I need with the Samsung chip. 3GB Ram 16 GB rom.

Until now I have tried with USB Burning Tool the unbrick. But I always have an error at 7%.
I also have questions about the tool. Do I need separate files for each firmware in the license folder?

I hope you can help me and I understand the approach.

Regards

[mralimz]

I have a CZ-S32-V5 no sign of any smasung chip or DDR chips says it's DDR3. But I do have a Toshiba so not sure which is right shorting pins for me

same as mine.. CZ-S32-V5 with ddr3 ram .. failed at 2% with any firmware from here .. please advise

[BR6]

I have a CZ-S32-V5 no sign of any smasung chip or DDR chips says it's DDR3. But I do have a Toshiba so not sure which is right shorting pins for me

[hcardoso483]

I can flash using your method, but when it's finished I can see the superceleron android picture but nothing append... It's freeze on picture.
now it's better, I've an image and see the green android bar .Before flashing with sd card I was flashing with usb cable but never see h96 Pro picture or superceleron picture...only blackscreen
an idea to fix my issue?

Hello again, my naigbor has that same as we and he was successfully only on the 3rd attempt he stayed that right at the end on the 1st and 2nd attempt it fails about close to finish if this is same with you try until you get it eventually will work it has to be v4 cos v5 and v6 already have twrp recovery, good luck I know you will get it to boot, don't bother with short pin method it works only on the A912 it doesn't work with the S912

Sent from my Nexus 10 using Tapatalk

[pulesky]

Hi again ,

that is for sure long enough , hope you get it .

good luck / gefattern

Hi,

I will try to shortcut the pin of Band but mine is not Samsung... I will try to found documentation about on web...

[gefattern]

Hi again ,

that is for sure long enough , hope you get it .

good luck / gefattern

[pulesky]

Hi pulesky ,

how long did you wait ???

gefattern

For 20 min

[gefattern]

Hi pulesky ,

how long did you wait ???

gefattern

[hcardoso483]

I can flash using your method, but when it's finished I can see the superceleron android picture but nothing append... It's freeze on picture.
now it's better, I've an image and see the green android bar .Before flashing with sd card I was flashing with usb cable but never see h96 Pro picture or superceleron picture...only blackscreen
an idea to fix my issue?

Okay now you do the same thing all over again but with the stock rom if is like mine the usb connection will never work again so back to stock same method and hopefully you get yor box back

Sent from my Nexus 10 using Tapatalk

[pulesky]

H96 Pro Plus Umbrick i have this box and it was bricked so what i did was i downloaded superceleron h96 pro plus scv4 for ddr3 and ddr4 it is a 7.1.2 rom and i puted in a sdcard using the burn card metod then after the computer finishes i got the card to the box pluged the hdmi cable power on tv power on box with tooth pic inserted and gess what it started to flash now all is well, try this, let me know

Sent from my H96_PRO_PLUS using Tapatalk

I can flash using your method, but when it's finished I can see the superceleron android picture but nothing append... It's freeze on picture.
now it's better, I've an image and see the green android bar .Before flashing with sd card I was flashing with usb cable but never see h96 Pro picture or superceleron picture...only blackscreen
an idea to fix my issue?

[hcardoso483]

H96 Pro Plus Umbrick i have this box and it was bricked so what i did was i downloaded superceleron h96 pro plus scv4 for ddr3 and ddr4 it is a 7.1.2 rom and i puted in a sdcard using the burn card metod then after the computer finishes i got the card to the box pluged the hdmi cable power on tv power on box with tooth pic inserted and gess what it started to flash now all is well, try this, let me know

Sent from my H96_PRO_PLUS using Tapatalk