[ROM] AlfaWise H96 PRO+ 3/16Gb - 3/32Gb - 3/64Gb - SCV7A 7.1.2 (DDR3/DDR4 and 9377 Wifi Chipset)

[nickgr]

Ah, so you have a V6 board as well... LP is a V6 firmware. The reason we need newer firmware is because our boards have a single LPDDR chip, which is partitioned differently than previous memory configurations, of more than one chip.

I really liked the latest factory firmware, as it ran smooth and was very stable. Just had to have ATV because I wanted more ATV apps. Only a few would not run, and I am now looking into why, as my modded build.prop may be the root cause. As I disabled non existant features like phone, and data. I think some phone and dual purpose apps (install on both TV and Phone) may fail because of my edits to the build.prop.

found one ATV app that breaks because of it, but that app is a dual purpose app.

I think If I had not messed with the build.prop, the factory firmware would run everything I needed, as long as I had TV launcher for my launcher.

try the factory firmware for a week. It is the best I have seen that came out this year for low cost s912 TV boxes.

I have tried the one I mentioned above (don't know If it's the original or not) but it was freezing and force closing all the time so I tried installing SuperCeleron's rom.

[X92-2GB]

Thanks for the reply. Installing the latest factory firmware and going from there is a good idea but unfortunately I'm not sure which one is the right one. The only one that I'm sure it will boot is this one:
aml_7.1.2_s912_q9377-S912_LP_mac-20180409.img

Ah, so you have a V6 board as well... LP is a V6 firmware. The reason we need newer firmware is because our boards have a single LPDDR chip, which is partitioned differently than previous memory configurations, of more than one chip.

I really liked the latest factory firmware, as it ran smooth and was very stable. Just had to have ATV because I wanted more ATV apps. Only a few would not run, and I am now looking into why, as my modded build.prop may be the root cause. As I disabled non existant features like phone, and data. I think some phone and dual purpose apps (install on both TV and Phone) may fail because of my edits to the build.prop.

found one ATV app that breaks because of it, but that app is a dual purpose app.

I think If I had not messed with the build.prop, the factory firmware would run everything I needed, as long as I had TV launcher for my launcher.

try the factory firmware for a week. It is the best I have seen that came out this year for low cost s912 TV boxes.

[nickgr]

Sounds like you may have an odd build on your box. I would get a stuck boot with flashing firmwares not made for my box. Example: flashing SuperCeleron 64bit GT1 on my mini M8S Pro -C.

since there are many different versions of the same box, I would try flashing the latest factory firmware and see if turning off erase bootloader will allow booting with this firmware.

I haven't tried to flash this firmware on my V6 H96pro+, as it has problems with the update, as I found in flashing ATV. Found a recent Russian updated firmware of the SCV4 ATV, which corrects the issues with boot partition at least on the V6 board.

Thanks for the reply. Installing the latest factory firmware and going from there is a good idea but unfortunately I'm not sure which one is the right one. The only one that I'm sure it will boot is this one:
aml_7.1.2_s912_q9377-S912_LP_mac-20180409.img

[X92-2GB]

I solved my own problem. The card has to be formatted in FAT32 or else the update doesn't start. However now that it finished the box still freezes before starting the SuperCeleron rom like it did when I used the USB method

Sounds like you may have an odd build on your box. I would get a stuck boot with flashing firmwares not made for my box. Example: flashing SuperCeleron 64bit GT1 on my mini M8S Pro -C.

since there are many different versions of the same box, I would try flashing the latest factory firmware and see if turning off erase bootloader will allow booting with this firmware.

I haven't tried to flash this firmware on my V6 H96pro+, as it has problems with the update, as I found in flashing ATV. Found a recent Russian updated firmware of the SCV4 ATV, which corrects the issues with boot partition at least on the V6 board.

[nickgr]

I solved my own problem. The card has to be formatted in FAT32 or else the update doesn't start. However now that it finished the box still freezes before starting the SuperCeleron rom like it did when I used the USB method

[nickgr]

I usted this method : https://youtu.be/YvSXRW7oxdQ

I watched the video many times but only managed to see the recovery menu by pressing and holding the reset pin

[nickgr]

So smth. is wrong wth the SD card.

It's a brand new Samsung 64GB SD card, I haven't used it anywhere else.

[Dr.Pancho]

I tried the SD card method but couldn't get to the "update" screen. Instead of that the recovery menu appeared when I pressed and hold the reset pin

I usted this method : https://youtu.be/YvSXRW7oxdQ

[lyubodelev]

I tried the SD card method but couldn't get to the "update" screen. Instead of that the recovery menu appeared when I pressed and hold the reset pin

So smth. is wrong wth the SD card.

[nickgr]

Hi. It's the same hardware as my box. In my case SCV4-SCV7A works perfectly.
I could not make the flash by USB BURNING TOOL, and if I could do it by SD CARD.
Did you try SDCARD method?

I tried the SD card method but couldn't get to the "update" screen. Instead of that the recovery menu appeared when I pressed and hold the reset pin

[Dr.Pancho]

Hello everyone, I have the H96 Pro+ 3/16 which you can see in the following pictures:

https://imgur.com/a/8VWpCJ3

I am trying to install SuperCeleron's rom via USB and although it flashes without problems the box never starts. It freezes a little after the initial splash screen. Is there any change that the rom is not compatible with this box? Is there anything else I can try? Thank you in advance

Hi. It's the same hardware as my box. In my case SCV4-SCV7A works perfectly.
I could not make the flash by USB BURNING TOOL, and if I could do it by SD CARD.
Did you try SDCARD method?

[nickgr]

Hello everyone, I have the H96 Pro+ 3/16 which you can see in the following pictures:

https://imgur.com/a/8VWpCJ3

I am trying to install SuperCeleron's rom via USB and although it flashes without problems the box never starts. It freezes a little after the initial splash screen. Is there any change that the rom is not compatible with this box? Is there anything else I can try? Thank you in advance

[kokopo]

Ok, i try it, thx

[lyubodelev]

Is this the rom sure about this model?
https://www.geekbuying.com/item/H96P...OX-380991.html

Just try it... After that I will give you a patch for the remote...For best work you must have a wireless mouse!

[kokopo]

Is this the rom sure about this model?

https://www.geekbuying.com/item/H96PRO--2GB-16GB-Amlogic-S912-TV-BOX-380991.html