If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
mine is 7.1.2 isnt it enough to just reset factory data as its to complicated and secondly all videos instruct for reset witha pin than there are again many steps
do u know this companys site where we can reqeat for a firmware update for thes bugs and gliches
Geeze! Why did you buy the box, if you cannot learn to reset. Android has been hokey since its conception, and If you haven't learned by now then don't play with android devices.
hopefully you can return for a refund and move on. Way too many peeps who won't bother to learn, just jump Into flashing and bricking their devices. No wonder devs don't like to support their work after time. It started with XDA and now here.
what's even more funny is peeps with Note 8 phones plaguing Note 8.0 tablet areas. Not that they're confused with the device name, but haven't got a clue that the tablet got Kitkat not Oreo and is no longer supported.
u r so right about these slum areas manufacturers. no updates or no maintanance of software. by the u have any idea if there any offical site of h96pro plus for complain or support for software issues
I also had a bricked H96 Pro Plus (3gb RAM / 16Gb flash), after trying to unroot the device with SuperSU.
I spent many, many hours reading many, many threads and i eventually found the solution. So a big THANKYOU to everyone who has posted problems and solutions. Without your help my H96 Plus + would still be bricked.
Initially, my box wail fail at the H96 Pro logo, but for some reason wouldn't even output to HDMI, with only a feint blue LED.
This is what I learnt.....
- no HDMI output doesn't mean it is totally bricked
- it took me a while to work out that only 1 usb socket on the box works (closest to the SD card)
- usb burning tool 2.0.8 worked fine
- laptop must use usb 2.0 (usb 3.0 does NOT work!)
- there is NO NEED to connect the box to a power supply. The eMCC h96 flash can be powered and accessed from the laptop usb 2.0 alone
- the laptop usb 2.0 will sometimes reduce power output if it doesn't see activity for a few minutes (so try unplugging/replugging if failure)
- the connection between h96 and laptop can be started 3 ways and is not fussy
option 1. click start on the laptop with usb already connected
option 2. connect the usb with the flash process already started
option 3. use a paperclip to reset the box with the usb already connected and flash process started
- all the above methods will cause the flash process to restart
- it is VERY important to try lots of dfferent ROM's!!
- sometime a ROM will stop a 2% every time
- some ROMs will appear to stop at any random point (2%, 10% 90% etc.) each time it is run. I thought this was a problem with power, or usb cable, but it was just the WRONG ROM!
- the "aml_7.1_s912_q9377-H96PROPLUS_mac-20170422" rom didn't work for me, and crashed out at random %
- after about 10 ROMS , "aml_7.1_s912_q9377-H96PROPLUS_LP_KDMC_mac-20171010" worked with success!!
My method;
1. start laptop and load USB Burning tool 2.0.8
2. open ROM 20171010 above (MAC licence issue already fixed)
3. click start
4. connect box to laptop with correct usb sockets
5. flash process auto starts
6. success!! - unplug usb
7. click stop
8. connect h96 to tv and power on - first boot took about 5 minutes
I have same problem as your can you tell me where to find this image
"aml_7.1_s912_q9377-H96PROPLUS_LP_KDMC_mac-20171010
i used your image and this imaage atvX-s905x_RTL_SSV_LPDDR3_v4.0_4
both of them give me error at 2% of course i short pin 5 and pin 6 the PC recognize driver but still i stuck with errors
CZ-S32-v3 (DDR4) (use aml_7.1.2_s912_q9377-H96PROPLUS_mac-20180409_shmod-k4-stockbl)
it uses the factory bootloader so there's no problems with the ram slight speed bump
.
.
.
as you recommended i used this image aml_7.1.2_s912_q9377-H96PROPLUS_mac-20180409_shmod-k4-stockbl (v2.2 + v3)
but still give me error at 2%
do i need differnt version of USB Burining Tool?
We process personal data about users of our site, through the use of cookies and other technologies, to deliver our services, personalize advertising, and to analyze site activity. We may share certain information about our users with our advertising and analytics partners. For additional details, refer to our Privacy Policy.
By clicking "I AGREE" below, you agree to our Privacy Policy and our personal data processing and cookie practices as described therein. You also acknowledge that this forum may be hosted outside your country and you consent to the collection, storage, and processing of your data in the country where this forum is hosted.
Comment