UGOOS UT8 Pro Android 11 TV BOX RK3568 Quad-core A55 8GB RAM 64GB WIFI6 Gigabit RJ45 SAMBA HDR:

[gefattern]

Hi ,

Still a RK3568 not RK3588 , still not to buy from them , not A13 ,

a little bit more investment and you got the Shield and i am nearly

sure it is a test-key Firmware , no "release" Version . If they would

do a little bit more and better Support they could sell much more ,

but nearly no chinese TVBox Company has a well working Support

where the Users will be taken seriously and Bugs will be really fixed ,

hope they learned and will do it right ,

greetings / gefattern

[micara]

Hei Everyone from a long time of search for twrp recovery rk3568
I found this image recovery costum made for pi twrp_3.6.2_rpi3a_a11tv.img from https://forum.radxa.com/t/rock-3a-tw...ery-mode/10915
I already edited with kitchen is aosp i saw many times rk3568 inside the files but most of them are gibrish for me. so not to be smart-s and because
i dont understand the meaning of them .I'm asking everyone that has knowlege and has time to check or if can be adapted for ugoos rk3568
will be appreciated
Thank you Everyone

[gefattern]

Hei Everyone from a long time of search for twrp recovery rk3568
I found this image recovery costum made for pi twrp_3.6.2_rpi3a_a11tv.img from https://forum.radxa.com/t/rock-3a-tw...ery-mode/10915
I already edited with kitchen is aosp i saw many times rk3568 inside the files but most of them are gibrish for me. so not to be smart-s and because
i dont understand the meaning of them .I'm asking everyone that has knowlege and has time to check or if can be adapted for ugoos rk3568
will be appreciated
Thank you Everyone

Hi ,

more Info for your Box you will find on telegram , there is a English and a Chinese Channel for Ugoos ,

im am Member too , i have a X4Q Pro ,

greetings / gefattern

[micara]

Hi ,

more Info for your Box you will find on telegram , there is a English and a Chinese Channel for Ugoos ,

im am Member too , i have a X4Q Pro ,

greetings / gefattern


Thank you

[micara]

Hi Everyone

I tried to flash the twrp as it is tell me if i did wrong anything

I"M familiar with adb commands because I have nvidea2017 I know how they work and i alredy try it.

If anyone to want know I will try to be detalied of my expirience of the try.

Before starting you have to know uses TWRP-compatible device non-dynamic partitions A/B
so

C:\adb>fastboot flash recovery twrp.img
Warning: skip copying recovery image avb footer (recovery partition size: 0, recovery image size: 48758784).
Sending 'recovery' (47616 KB) OKAY [ 1.539s]
Writing 'recovery' FAILED (remote: 'cannot find partition')
fastboot: error: Command failed

NOT WORKING

Preparation

Windows
1 - Minimal adb Fastboot
2 - Connect BOX and Install drivers

Android
1 - Enable Developer Options
2 - Enable USB debugging

pair the devices an start

-adb reboot bootloader = Start BOX on bootloader
-fastboot devices = UT8P230300000247 unauthorized

ON fastboot devices YOU ARE unauthorized EVEN YOW pair the device

-fastboot oem unlock = ( NOT WOKING - ERROR_FAILED (remote: 'not implemented')
so you go arownd

-fastboot getvar current-slot
get-current-slot: a
-fastboot --set-active=_b
change-current-slot
-fastboot flash boot twrp_3.6.2_rpi3a_a11tv.img
Rebooted
YOU GET BOOT_LOGO loop and the BOOT_LOGO changes pull the power cord couple times and the box restarts.

so i flashed on ( A PARTITION )
YOU GET BOOT_LOGO loop and the BOOT_LOGO changes - dead that it You have to reflash original

Because of BOOT_LOGO changes and been reading a lot on 4PDA FORUM I think recovery and kernel are on same partition
so to twrp recovery img has to be adapted with the kernel of the any device
and that is the reason that TWRP DROPPED the rockchip support to match effort to adapt any rk3568 kernel
-
-
When you unpack the img some picks

Supplied image: boot.img

Setting up work folders . . .

Image type: AOSP

Splitting image to "split_img/" . . .

ANDROID! magic found at: 0
BOARD_KERNEL_CMDLINE console=ttyFIQ0 androidboot.baseband=N/A androidboot.wificountrycode=CN androidboot.veritymode=enforcing androidboot.hardware=rk30board androidboot.console=ttyFIQ0 androidboot.verifiedbootstate=orange firmware_class.path=/vendor/etc/firmware init=/init rootwait ro init=/init androidboot.selinux=permissive buildvariant=userdebug
BOARD_KERNEL_BASE 0x10000000
BOARD_NAME
BOARD_PAGE_SIZE 2048
BOARD_HASH_TYPE sha1
BOARD_KERNEL_OFFSET 0x00008000
BOARD_RAMDISK_OFFSET 0x01000000
BOARD_SECOND_OFFSET 0x00f00000
BOARD_TAGS_OFFSET 0x00000100
BOARD_OS_VERSION 11.0.0
BOARD_OS_PATCH_LEVEL 2021-07
BOARD_HEADER_VERSION 2
BOARD_HEADER_SIZE 1660
BOARD_DTB_SIZE 124720
BOARD_DTB_OFFSET 0x01f00000

Unpacking ramdisk to "ramdisk/" . . .

Compression used: gzip
48129 blocks

Done!

[yougz]

Hi, what are the best solutions to switch the Ugoos UT8 TV box to ANDROID TV?

How to get the Android TV version of YouTube?