MK809 III may be bricked :((( please help me

[mancycro]

Today I flashed my MK809III with this : http://www.freak-tab.de/neomode/nhr_18_ap6210_1080.zip
... Now when i plug it on there is no red light on stick and there is flashing light on power adapter. When i plug it in pc and press recovery button, pc dont do anything, like i didnt plug it.. Can someone help me with this.. i afraid my stick is dead :SS

[mancycro]

[TVDroid]

Try this - http://www.freaktab.com/showthread.p...400-All-in-One

But your PC must connect to your Device. Have you try the Pin 8/9 Mod ?

My is the same Board, see here - http://www.freaktab.com/showthread.p...l=1#post115713

[mancycro]

I tried to install drivers from this pack but unsuccessful :S I tried to do with this pin but there is no light on led... i dont know is it drivers fault now for not erasing nand ...

[useq]

Emmm.. sorry if you tryed this but
1. press recovery/factory reset button
2. holding above plug it in to power (not the PC)
3. Still holding use another cable to plug into pc
4. release button

worked for me

[mancycro]

Nothing happened, the led flash is still not working

[darekmarta1975]

Nothing happened, the led flash is still not working

This is a physical damage

[mancycro]

Can it be repaired somehow? :S

[darekmarta1975]

do not fix it myself

[useq]

well, if you still have a warranty on it ... close it up .. send it off and play dumb :/

[ATB]

The red led light indicates your stick is alive ... without it there would be no way to connect it to your PC .... if you short pins 8,9 that could bring it into what they call mask rom mode .. and then you'd need to flash a factory rom to it ...

1) make sure nothing is connected to your stick
2) short pins and power up ... (make sure the pins are shorted first)
3) power up again ... you should have your red light back .. if not you've probably got a brick
4) you can then use your otg port to flash a stock rom onto your stick

[Nikolay]

Help me please. When power on, MK809iii not start (no image on the HDMI port), but i have a red light on stick. When i plug it in pc and press recovery button, pc dont do anything. But if i short pins 8,9 PC found stick and inRKDevelopTool_v1.37 - "Found RKAndroid MaskRom Rock USB", but if press EraseIDB - "ERROR: Download boot failed". How i can flash it??? in RKBatchTool same problem -


**********Upgrade Action**********
**********Upgrade Start Total<1>**********
<Layer 3-2> Download Boot Start
<Layer 3-2> Download Boot Fail
**********Upgrade Done Success<0> Fail<1> Time<5070>ms**********

thanks!

[darekmarta1975]

The red led light indicates your stick is alive ... without it there would be no way to connect it to your PC .... if you short pins 8,9 that could bring it into what they call mask rom mode .. and then you'd need to flash a factory rom to it ...

1) make sure nothing is connected to your stick
2) short pins and power up ... (make sure the pins are shorted first)
3) power up again ... you should have your red light back .. if not you've probably got a brick
4) you can then use your otg port to flash a stock rom onto your stick

read carefully unless I wrote the equipment for repair, surely not written with LED candles and this means that there is no power

[darekmarta1975]

Help me please. When power on, MK809iii not start (no image on the HDMI port), but i have a red light on stick. When i plug it in pc and press recovery button, pc dont do anything. But if i short pins 8,9 PC found stick and inRKDevelopTool_v1.37 - "Found RKAndroid MaskRom Rock USB", but if press EraseIDB - "ERROR: Download boot failed". How i can flash it??? in RKBatchTool same problem -


**********Upgrade Action**********
**********Upgrade Start Total<1>**********
<Layer 3-2> Download Boot Start
<Layer 3-2> Download Boot Fail
**********Upgrade Done Success<0> Fail<1> Time<5070>ms**********

thanks!

when purchased MK 809III because new vehicles are new loader and not you upload a different firmware

[useq]

when purchased MK 809III because new vehicles are new loader and not you upload a different firmware

"wybacz stary ale to co napisałeś nie ma sensu" <= means sorry mate but that sentence have no sense at all


Nikolay try another firmware, Like Neomode v1.0 or 1.7??
try flash with stock rom...??