Modded ROM's for Tronsmart R68 "Tronsplant your ROM"

[Stzo]

I have installed the latest v9 Rev3 and still have an issue with DTS Audio over HDMI where it will drop sound just long enough for you to notice it. Is there a setting I need to change, a change in connection to my receiver, or is this still an active issue with this firmware iteration.

Please try to go back to 8.3, that works perfectly to me on my Tronsmart R68 META Gblan vesion.

[gotpaste]

I have installed the latest v9 Rev3 and still have an issue with DTS Audio over HDMI where it will drop sound just long enough for you to notice it. Is there a setting I need to change, a change in connection to my receiver, or is this still an active issue with this firmware iteration.

[[email protected]]

Hello everyone,

After all the below done correctly, I still cannot boot Z68 to RECOVERY Mode. (Apply power first, then immediately press and hold the button in the small hole).

1. Boot Z68 to Boot loader (hold reset button during power up)
2. Flashed TWRP image (TWRP_2.8.7.0_R68.img) to Addr 0x00028000 using AndroidTool v2.35
3. AndroidTool indicated a GOOD flashing

Am I missing something?

Please advise, Thank you

[251643711]

7th March 2016 ACTIVATION in addition to this activation of the patch, but also the need for a file, I that device used or to jump activation

[clarkss12]

Maybe this will help to show you how to get your I/O working.

https://www.youtube.com/watch?v=7UGmgh4gjBw

[251643711]

I have another device can directly brush X6 firmware, but the remote control and WiFi can not be used, as well as to activate, ask how to solve these problems, thank you!!!

[Vinc3nzo]

Hi Lonix!

In V9.3, I have activate sleep screensaver. But after 15mn the Box Is reboot in loop.

[lonix]

guys! Can anyone point me to a way to disable HDMI switching off the TV box? Whats the name of this feature? Is it CEC? I presume there's a config file for that. Thanks!

This has been covered in this thread before.

The easiest solitiuon is to rename the file
/system/lib/hw/hdmi_cec.rk30board.so

to

hdmi_cec.rk30board.bak

[Stzo]

guys! Can anyone point me to a way to disable HDMI switching off the TV box? Whats the name of this feature? Is it CEC? I presume there's a config file for that. Thanks!

Yes, HDMI-CEC.

[l30ns]

guys! Can anyone point me to a way to disable HDMI switching off the TV box? Whats the name of this feature? Is it CEC? I presume there's a config file for that. Thanks!

[Aaron407]

Does the autorefresh switching in the 9v3 version of ZDMC work without any sync issues *while bitstreaming passthrough surround sound audio* after updating superuser? That sync issue is my biggest quibble at this point as I currently keep everything at 60 fps instead of allowing autoswitching to 24p.

[Stzo]

Hi Guys,

I tried it:

plugin.video.youtube-master

https://mega.nz/#!qhVFnJ7K!JFuBJWkYRs19S_XeLn0rsTCUBqNc-pAVOOoZU_Q8N-8

addon for KODI, this is the first way getting auto-framerate changing of YouTube videos I found. It works perfectly!

[[email protected]]

Thank you, Stzo.
I will give it a try later this week.

[Stzo]

Hi Lonix,

I tried to flash your new v9 Rev3 (flashable update) to my Z68, but I could not figure out how to do that., because this version does not have any image files (*.img).
Could you or any one help?

By the way, I only installed the v9 Rev2 FullROM and flash the Z68 stock kernel.img and resource.img to its relevant partition, and appeared my Z68 running OK, the box does not reboot, freeze or get hot but does not have passthrough options in Kodi, and some other minor issues.
Overall, the V9 Ver2 is the best for now. Thank you for your hard work.

I just wanted to update V9 Ver3 to get all update from Zidoo 1.0.36 base

Thank you everyone for your help.

Hi [email protected],

If looking for a fully operational firmware for Z68, please check this post too:

http://freaktab.com/forum/tv-player-support/rk3688-devices-aa/nexbox-z68/firmware-roms-tools-bh/560796-nexbox-z68-rk3368-new-rom-s-updated-17-03-2016?p=571749#post571749

[lonix]

Hi Aaron407,
I think I got the idea now. I will follow your instruction t do it tonight.

Thank you so much for your help.

When you flash the 9-3 zip file, also reflash SuperSU straight after, download here

http://download.chainfire.eu/supersu-stable